Silent Alert DDA Quick Start Manual

PUSH

Status light

Test button

Configuration

switch Cover

PP3 battery

contacts

Screw cap

Screw cap

CCD4A-2220-EU

CARE CALL
MINI MAGNETIC
DOOR MONITOR

USE ALKALINE PP3
9 V BATTERY ONLY

Batch 06/01/14

www.silentalert.ie

Silent Alert International, IRL

Tel: [phone]

Keys 1-4 System

Channel
Key 5=10 Sec Delay
Key 6=20 Sec Delay

Keys 5+6=30 Sec Delay

Key 7 Leave ON
Key 8 Not Used

USE WITH MAGNET SUPPLIED

PP3 Battery

PUSH

PUSH

The light will then flash green

several times to show the

battery voltage.

9 flashes = 9Volts in the battery.

When a battery is first fitted the
indicator light will flash red then

green a few times.

1.

Install a 9 volt PP3 alkaline or lithium battery

making sure to observe the correct polarity.

PUSH

If the light flashes red at this

point the battery is flat

and will need to be replaced.

To repeat the battery check remove the battery, press the test

button then re-insert the battery to start the sequence again.

TD4A

MONITOR
USE ALKALINE PP3
9 V BATTERY ONLY

Batch 06/01/14

www.silentalert.ie

Silent Alert International, IRL

Tel: [phone]

Keys 1-4 System

Channel
Key 5=10 Sec Delay
Key 6=20 Sec Delay

Keys 5+6=30 Sec Delay

Key 7 Leave ON

Key 8 Not Used

USE WITH MAGNET SUPPLIED

PUSH

1 2 3 4 5 6 7 8

Configuration switches shown

with cover removed.

Input

terminals

Standard operation

TM

Silent

Alert

It is possible for the monitor to light up different keys on the Pager or SignWave.

1 2 3 4 5 6 7 8

Move the relevant key

to the right .

Press the test button

and check the correct

event is received by the

Pager or SignWave

1 2 3 4 5 6 7 8

1 2 3 4 5 6 7 8

1 2 3 4 5 6 7 8

For more information on configuring the Mini Monitor please refer to the dedicated quick guide supplied
with each unit. Alternatively, you can download the information from out website at www.silentalert.ie.

This quick start guide explains the process of connecting Silent Alert equipment to certain Telecare communicators for
DDA compliance.
Whilst a wireless smoke alarm unit will alert the call centre, a deaf or hard of hearing person may miss the alarm and be
unaware of the danger. By using a Silent Alert DDA kit, the user will be alerted immediately and can respond or react
as necessary. This ensures deaf and hard of hearing people can be made aware of integrated Telecare smoke alarms
whilst reducing false alarm call outs.
The user will also be able to expand on the benefits of the Telecare system by having access to doorbell, telephone, baby
alarm and door entry systems whilst still having the security of a remotely monitored smoke alarm and emergency pendant.

1 2 3 4 5 6 7 8

Move control keys

5, 6 & 7 to the right.

2.

3.

The monitor will now trigger

when the telecare unit activates

its external output.

A fire signal will be sent to the

Pager or SignWave when the

Telecare relay activates.

4.

A
B
54

3
2
1

ON /OFF

ON

Enabling deaf or hard of
hearing people to respond to
Telecare smoke alarms.

TM

Silent

Alert

Compatible

TM

Silent

Safe

Fir

Alert

e

TM

Silent

Alert

Quick start guide DDA kit

Mini Monitor for use with Telecare Communicators

Any questions? Call us on

[phone]

This information is not intended to replace the manufacturers user instructions. The assistance of the Telecare
providers technicians will be required to enable correct output.

Connecting to Tynetec Reach+

WARNING

Do not connect the equipment in any way other than illustrated.

Silent Alert International accepts no responsibility for damage caused by incorrect installation.

The following quick guide will explain how to link the Silent Alert system to Telecare communicators. Always refer to the
Communicators installation instructions before connecting our unit to the system. The Telecare technician should refer to
the page 27 of the Reach plus installation guide for information on the the ZSA556A interface unit.

1.

5.

Ensure the common (negative) wire
is connected to terminal 1 on the
mini monitor to avoid false triggering.

1

3

Connect the free end to the
Mini Monitor and secure with
the locking screws

The monitor will now
trigger the Pager or
SignWave each time
the telecare
system activates.

1 2 3 4 5 6 7 8

On the Mini Monitor
move control key 7 to
the right.

PUSH

TM

Silent

Alert

This will configure the
monitor to trigger on a
short circuit.

4.

NO

NC

COM

0V

IP4

IP3

IP2

IP1

Tynetec ZSA556A

Clean contact relay output
(Rated @ 24V 1A)

2.

Connect a suitable length of twin core low
voltage cable to terminals NO & COM of the
Tynetec unit (shown here in grey and black).

Ensure the wiring is neat and
secure and fit the lid back to
the box.

6.

#

1 1

7

The unit will announce "Hardwired Output DTMF tone"

0

3

0

1

Configuring the hardwired output

Enter

Enter 2 digits for the DTMF tone (00 to 15) and the unit will announce "Duration")

Enter 2 digits for the time in seconds (0 to 99) you want the relay to remain latched followed by #.

Enter

to select Tynetec DTMF tone 03.

#

Enter

The Tynetec reach plus is configurable using the keypad on the rear of the unit.

TM

Silent

Alert

Quick start guide DDA kit

Connecting Silent Alert to the Tynetec Reach+

Any questions? Call us on

[phone]

Silent Alert International

www.silentalert.ie

[phone]

Connecting to Tynetec Reach+ via the Tynetec ZSA556A I/O module