Silencer 8900 Series Owner's Manual

OWNER’S

MANUAL

Model: 8900 Series

Vehicle Immobilizer

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference; and
(2) This device must accept any interference received, including interference that may cause undesired operation.

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to
this equipment. Such modifications could void the user’s authority to operate the equipment.

Silencer products have been designed to provide the consumer with years of trouble-free operation.

Disarm

Valet

On

Valet

Off

This manual will provide reference for the operation and maintenance of your new Silencer vehicle
immobilizer system. Please, take a moment to read this manual so you will be familiar with the oper­ation of your new system.

1-Button Automatic

3-Button Transmitter

1-Button Transmitter

Disarm Transmitter

Note: Depending on the type of consumer transmitter package your dealer provided you with, you

may have each one of the transmitters pictured above, or two of the same type transmitter. Confirm
this with your dealer.

Automatic Arming

Once you have turned the ignition key to the “Off” position, your Silencer engine immobilizer will
become armed within 30 seconds. Upon arming, the device will emit 1 soft chirp. Restarting the
engine before 30 seconds will stop the timer and reset it.
Note: If your system was supplied with an “Automatic Disarm Transmitter”, you will need to leave
the vicinity of your vehicle (approximately 60 feet) before the automatic arming function will execute.
(Remaining in close proximity of your vehicle could prevent it from arming). The distance require­ment may prevent you from hearing the soft arming chirp.

Manual Disarming

3-Button Transmitter:

When you return to your vehicle to start the engine, press the “Disarm”
button on the 3-button transmitter. When the system is disarmed, the device will emit 2 chirps
indicating it’s disarmed.

1-Button Transmitter: When you return to your vehicle to start the engine, press the transmitter

button. When the system is disarmed, the device will emit 2 chirps indicating it’s disarmed.

Automatic Disarming (Automatic Disarm Transmitter Required)

1-Button Automatic Disarm Transmitter: When you return to your vehicle, at some point, between

a distance of approximately 60 feet and the time you insert your ignition key to start the engine,
the automatic disarm transmitter will disarm your system. Once disarmed, the device will emit 2
chirps. No action is required by the operator.

Note: In areas of high radio frequency noise, the automatic disarm function of the transmitter may
get blocked or interfered with and not disarm your system. In this event, press the transmitter but­ton to perform a manual disarm.

2

Radio Frequency (RF) Protection Rearm Timer

Each time the system is disarmed using the transmitter the device will begin a protection mode
countdown. This is a timed secondary protection mode. If you do not start your vehicle within 60
seconds, your Silencer system will become rearmed and your engine will become disabled again.

Note: If your system operates from a “Automatic Disarm Transmitter”, the 60 second RF protection
timer will not time-out and will rearm your system if you remain within 60 feet of your vehicle.

1-Button Automatic Transmitter Mode Programming

If your transmitter package contains one or more of the 1-button automatic disarm transmitters, the
default operating mode will be “Manual Mode” (to preserve the battery life while not in use). To
change the operating mode to “Automatic Mode”, follow these steps:

1. Press the middle area of the button and hold it down until the LED light on the side of the but­ton becomes solid red. Release the button.
Note: The LED may flash. Continue holding the button until the flashing stops and the LED
becomes solid red.

2. Press and release the center of the button 3 times. You will notice that the red LED light will be
off.

3. Press and hold the center of the button until the LED flashes. Release the button.

3 flashes = The transmitter is in “Automatic Disarm” mode.
1 flash = The transmitter is in “Manual Disarm” mode.

4. Confirm the mode of the transmitter. Press and release the center of the button and watch the
flash sequence of the LED.

5. The transmitter operating mode can be changed at any time by following Steps 1-3. Confirm
the mode by following Step 4.

3