silavent ENX100HTP, ENX1002SC, ENX1002SP, ENX1002SCP, ENX1002SHTP Installation Instructions And Information Manual

HEAT RECOVERY FAN

The ENERGEX will provide energy efficient ventilation in toilets, bath and shower rooms. It may also be used to
reduce humidity and ventilate other rooms such as bedrooms, living rooms, offices and hallways etc. The
ENERGEX is supplied with an optional air filter to reduce the amount of soot, dust and pollen entering the room.
The ENERGEX heat exchange fan requires a fitting kit to complete the installation. Pull-cord models should not be
installed in ceilings. Models with pull-cord override option should have the pull-cord removed (cut off) before
installing in ceilings.

HEAT RECOVERY FAN RANGE

SINGLE SPEED

ENX100

Fan unit operates whilst switch live is supplied to the unit. Designed to be used with remote switch (not supplied).
Fan unit incorporates thermo-actuator operated air inlet and outlet shutters.

ENX100P

Fan unit operates whilst switch live is supplied to unit. Operated by the integral pull cord. Fan unit incorporates
thermo-actuator operated air inlet and outlet shutters.

ENX100T

Fan unit operates whilst switch live is supplied to unit. When the switch live is turned off, the fan continues to work
for a period between 45 seconds and 30 minutes (depending on the overrun timer setting). Fan unit incorporates
thermo-actuator operated air inlet and outlet shutters.

ENX100HTP

Fan unit operates whilst switch live is supplied to unit. When the switch live is turned off, the fan continues to work
for a period between 45 seconds and 30 minutes. The fan can also be operated by the integral pull cord which
enables the fan to run for the time period set on the timer adjustment. If the fan is off, the fan can also be switched
on by the integral humidity sensor. Fan unit incorporates thermo-actuator operated air inlet and outlet shutters.

TWIN SPEED

ENX1002SC

Fan unit is designed to operate with a remote switch. The fan will run at normal speed or high speed when the
remote switch is turned on. Fan unit does not incorporate thermo-actuator operated air inlet and outlet shutters.

ENX 1002SP

Fan unit is designed to be operated by the integral pull cord. When the pull cord is operated from the OFF position,
the fan will run at normal speed. When the pull cord is operated again, the fan unit will operate at high speed.
When the pull cord is pulled again, the fan switches off (Off-Normal-High-Off). Fan unit incorporates thermo­actuator operated air inlet and outlet shutters.

ENX 1002SCP

Fan unit is designed to operate with the integral pull cord. The fan will run continuously at low speed and will switch
to high speed when the pull cord is operated. When the pull cord is operated again, the fan

returns to the low

speed

. Fan unit does not incorporate thermo-actuator operated air inlet and outlet shutters.

ENX1002SHTP

Fan unit operates at high speed whilst switch live is supplied to the unit. When the switch live is turned off, the fan
continues to work for a period between 1 and 30 minutes.

The fan can also be operated by the integral pull cord

which enables

the fan to run at high speed for the time period set on the timer. If the fan is off, the fan can also be

switched on

to a reduced speed by the integral humidity sensor. Fan unit incorporates thermo-actuator operated air

inlet and outlet shutters. (Not continuous running)

ENX1

002SHB

Fan unit runs continuously at low speed and will switch to high speed when the integral humidity sensor detects a

significant increase in the level

of humidity. The unit is fitted with a switch live and pull cord so that boost may be

operated

independently from the humidity controls when required. Fan unit does not incorporate thermo-actuator

operated air inlet and outlet shutters

.

SELV MODELS

ENX 100LV

Fan unit

operates whilst switch live is supplied to transformer and the 12VAC output of the transformer is

connected to the fan. Designed to be used with remote switch (not supplied). Fan unit does not incorporate thermo-

actuator

operated air inlet and outlet shutters.

ENX

100LVT

F

an unit operates whilst switch live is supplied to transformer and the 12VAC output of the transformer is

connected to the fan. When

the switch live is turned off, the fan continues to work for a period of between 1 minute

and 30

minutes. Fan unit does not incorporate thermo-actuator operated air inlet and outlet shutters.

ENX 100LVHT

Fan unit operates

whilst switch live is supplied to transformer and the 12VAC output of the transformer is

connected to the fan. When the switch live is turned off, the fan continues to work for a period between 1 minute
and 30 minutes. The fan can also be

operated by the integral pull cord which enables the fan to run for the time

period

set on the timer adjustment. If the fan is off, the fan can also be switched on by the integral humidity sensor.

Fan unit does not incorporate thermo-actuator operated air inlet and outlet shutters.

Cleaning

ENERGEX
cover as previously described

with a soft dry brush or vacuum cleaner.

The front

The

outside of the fan body can be cleaned with a damp cloth.

The air

When clean, squeeze out any excess water BUT DO NOT WRING DRY, then layout on a flat surface to dry.

The heat exchanger should be rinsed under a cold tap and shaken to remove any surplus water

.
When all

It is recommended that every two years the fan chassis is removed from the mounting box to enable the air inlet to be

cleaned.

With the

Place the back plate to one side and dust the air inlet around the motor with a soft brush or vacuum cleaner.

When the

NOTE: Do not put any components in a dishwasher.