PRODUCT DATA SHEET
3
SikaQuick® Patch
RAPID CURING, TWO COMPONENT, REPAIR MORTAR FOR HORIZONTAL REPAIRS
PRODUCT DESCRIPTION
SikaQuick® Patch is a two-part, pre-proportioned
cementitous mix which when applied, produces a rapid
curing repair patch. It has been specifically formulated
and packaged to be an easy, mix-in-the-bag,
highstrength product. SikaQuick® Patch is based upon
Sika’s proven cement technology.
USES
Bonds to concrete▪
Horizontal spall repairs▪
Concrete basement floors▪
Concrete driveways▪
Concrete patios▪
Concrete side walks and much more▪
PRODUCT INFORMATION
Packaging
Shelf Life
Storage Conditions
29 fl. oz. (858 ml) pouch; 6 in a case
12 months in original, unopened containers
Store in cool, frost-free conditions with temperatures between 50 and 90°F
(10–32 °C). Condition product to between 65 and 77 °F (18–25 °C)
CHARACTERISTICS / ADVANTAGES
Packaged in a lightweight, easy to handle pouch▪
Simple application - just roll, mix and pour▪
Increased bond strength, Polymer Modified▪
Sets in 10 to 20 minutes (varies with temperature)▪
Interior or exterior use▪
Improved repair durability▪
Can drive over in 1 hour▪
No primer needed, just a damp surface, SSD (no
▪
standing water)
TECHNICAL INFORMATION
Compressive Strength
Product Data Sheet
SikaQuick® Patch
February 2019, Version 01.01
020302040030000308
1 /
1 hour 1,472 psi (10.1 MPa)
1 day 1,922 psi (13.2 MPa)
7 days 4,027 psi (27.7 MPa)
28 days 5,537 psi (38.1 MPa)
(ASTM C-109)
Tested at:
73 °F (23 °C)
50 % R.H.
Tensile Adhesion Strength
3
APPLICATION INFORMATION
228 psi (1.5 MPa)
(ACI 503 R)
Tested at:
73 °F (23 °C)
50 % R.H.
Coverage
Layer Thickness
Pot Life
Set Time
Final Set Time
Waiting / Recoat Times
Unit yields approx.: 1 ft2 at a half in. (12.7 mm) depth
Minimum Application Depth: 1/8”
Maximum Application Depth: 3”
1–5 minutes
5–10 minutes
10–20 minutes
30 minutes to 1 hour to drive on / 7 days to paint
(depending on humidity/temperature)
APPLICATION INSTRUCTIONS
SURFACE PREPARATION
Remove all deteriorated concrete, dirt, oil, grease, and
all bond-inhibiting materials from surface. Preparation
work should be done by high pressure water blast,
scabbler, or other appropriate mechanical means to
obtain an aggregate-fractured surface with a minimum
CSP 3 surface profile or greater. Ensure there are no
curing compounds or other contaminants remaining on
the substrate before application. Substrate must be
damp (SSD) before application. No standing water.
MIXING
Have scissors or a knife next to the hole or spall and
ready to cut a corner of the bag after mixing is
completed. Roll the pouch, starting at the compartment
containing Component A, working towards the ‘burst
seal’ in the direction of the arrows shown on the label.
Apply pressure to the rolled section to rupture the seal
and allow Component A (Liquid) to flow into the
compartment containing Component B (Powder). Mix
thoroughly by then rolling out the pouch and rubbing the
bag along any 90 degree surface (no sharp edges). Mix
for 20 seconds by forcing the material to travel inside
the bag, from one end to the other (using a “shoe
shining” technique). Make sure there is no powder left
behind, the clear packaging allows the user to see when
the product isproperly mixed.
LIMITATIONS
Do not apply on frozen or frost covered substrates.▪
Low temperatures or high humidity will extend curing
▪
time.
Low temperatures will cause a thicker consistency.▪
Do not allow stored product to freeze.▪
Do not apply on vertical surfaces.▪
BASIS OF PRODUCT DATA
Results may differ based upon statistical variations
depending upon mixing methods and equipment,
temperature, application methods, test methods, actual
site conditions and curing conditions.
OTHER RESTRICTIONS
ENVIRONMENTAL, HEALTH AND SAFETY
For further information and advice regarding
transportation, handling, storage and disposal of
chemical products, user should refer to the actual Safety
Data Sheets containing physical, environmental,
toxicological and other safety related data. User must
read the current actual Safety Data Sheets before using
any products. In case of an emergency, call CHEMTREC
at 1-800-424-9300, International 703-527-3887.
APPLICATION
After mixing, cut one of the bag’s corners and pour
mixed material in the hole/spall. The material will settle
into the hole/repair. Smooth it with a wide putty knife to
get a smooth/flat finish.
Product Data Sheet
SikaQuick® Patch
February 2019, Version 01.01
020302040030000308
2 /
LEGAL DISCLAIMER
3
• KEEP CONTAINER TIGHTLY CLOSED
• KEEP OUT OF REACH OF CHILDREN
• NOT FOR INTERNAL CONSUMPTION
• FOR INDUSTRIAL USE ONLY
• FOR PROFESSIONAL USE ONLY
Prior to each use of any product of Sika Corporation, its
subsidiaries or affiliates (“SIKA”), the user must always
read and follow the warnings and instructions on the
product’s most current product label, Product Data
Sheet and Safety Data Sheet which are available at
usa.sika.com or by calling SIKA’s Technical Service
Department at 1-800-933-7452. Nothing contained in
any SIKA literature or materials relieves the user of the
obligation to read and follow the warnings and
instructions for each SIKA product as set forth in the
current product label, Product Data Sheet and Safety
Data Sheet prior to use of the SIKA product.
SIKA warrants this product for one year from date of
installation to be free from manufacturing defects and to
meet the technical properties on the current Product
Data Sheet if used as directed within the product’s shelf
life. User determines suitability of product for intended
use and assumes all risks. User’s and/or buyer’s sole
remedy shall be limited to the purchase price or
replacement of this product exclusive of any labor costs.
NO OTHER WARRANTIES EXPRESS OR IMPLIED SHALL
APPLY INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. SIKA SHALL NOT BE LIABLE UNDER ANY
LEGAL THEORY FOR SPECIAL OR CONSEQUENTIAL
DAMAGES. SIKA SHALL NOT BE RESPONSIBLE FOR THE
USE OF THIS PRODUCT IN A MANNER TO INFRINGE ON
ANY PATENT OR ANY OTHER INTELLECTUAL PROPERTY
RIGHTS HELD BY OTHERS.
Sale of SIKA products are subject to the Terms and
Conditions of Sale which are available at
https://usa.sika.com/en/group/SikaCorp/termsandcondi
tions.html or by calling 1-800-933-7452.
Sika Corporation
201 Polito Avenue
Lyndhurst, NJ 07071
Phone: +1-800-933-7452
Fax: +1-201-933-6225
usa.sika.com
Product Data Sheet
SikaQuick® Patch
February 2019, Version 01.01
020302040030000308
Sika Mexicana S.A. de C.V.
Carretera Libre Celaya Km. 8.5
Fracc. Industrial Balvanera
Corregidora, Queretaro
C.P. 76920
Phone: 52 442 2385800
Fax: 52 442 2250537
SikaQuickPatch-en-US-(02-2019)-1-1.pdf
3 /
Loading...