SIIG TV Mount User Manual

Page 1
A
Fixed LCD TV/Monitor Mount - 10" to 24"
Installation Instructions
BCDEFG
(x4) bolt
(x4) concrete
anchor
washer
Step 1: Wall Plate Installation
Wood Stud Installation
1
Use a high-quality electronic stud finder (commercially available) to locate dead center of two studs and mark their locations with a pencil (figure 1-a).
2
Hold the wall plate to the wall and mark four locations to be used for mounting the wall plate.
3
Take down the plate and drill four holes at the position you've marked.
4
Attach the wall plate to the wall again and insert the bolts (A) and large washers (D) into the holes (figure 1-b) and tighten.
(x4) large
washer
(x4) M4X12
screw
(x4) M5X12
screw
(x4) M6X12 screw
04-0525A
Page 2
Concrete/Brick Wall Installation
1
Place the wall plate against the wall and mark four locations to be used for mounting the wall plate.
2
Pre-drill four holes at the positions you've marked and insert one concrete anchor (B) into each hole.
Position the Wall Plate onto the wall again and insert the bolts (A) and large
3
washer (D) into the anchor as shown (figure 1-b) and tighten.
Step 2: Display Plate Installation
Place your TV screen down on a soft, flat surface, and locate the threaded
1
mounting points that are located on the back of the display.
2
According to the size of the display's hole, choose the corresponding screw (E/F/G) and small washer (C) and insert into the hole as shown (figure 2-a) and tighten.
Step 3: Final Installation
Hang the display plate onto the top of the
1
wall plate and slide it onto the wall plate as shown (figure 3-a).
Maintenance
Check the mounting screws every two months for tightness.
IMPORTANT: If you don't understand the installation instructions, please consult an installation specialist
Page 3
Technical Support and Warranty
QUESTIONS? SIIG ’ s Online Support has answers! Simply visit our web site at www.siig.com and click Support. Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit questions online and a technical support analysts will promptly respond.
SIIG offers a 5-year manufacturer warranty with this product. Please see our web site for more warranty details. If you encounter any problems with this product, please follow the procedures below.
A) If it is within the store's return policy period, please return the product to the store where you purchased from.
B) If your purchase has passed the store's return policy period, please follow these steps to have the product repaired or replaced.
Step 1: Submit your RMA request. Go to www.siig.com, click Support, then click RMA to submit an request to SIIG RMA. If the product is determined to be defective, an RMA number will be issued.
Step 2: After obtaining an RMA number, ship the product.
• Properly pack the product for shipping. All software, cable(s) and any other accessories that came with the original package must be included.
• Clearly write your RMA number on the top of the returned package. SIIG will refuse to accept any shipping package, and will not be responsible for a product returned without an RMA number posted on the outside of the shipping carton.
• You are responsible for the cost of shipping. Ship the product to the following address: SIIG, Inc.
6078 Stewart Avenue Fremont, CA 94538-3152, USA RMA #: ________________
• SIIG will ship the repaired or replaced product via Ground in the U.S. and International
Economy outside of the U.S. at no cost to the customer.
Page 4
About SIIG, Inc.
Founded in 1985, SIIG, Inc. is a leading computer upgrade manufacturer of I/O connectivity products, including PCI & ISA serial and parallel ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b), networking, sound cards, and other accessories. SIIG is the premier one-stop source of upgrades. SIIG products offer comprehensive user manuals, many user-friendly features, and are backed by an extensive manufacturer warranty. High-quality control standards are evident by the overall ease of installation and compatibility of our products, as well as one of the lowest defective return rates in the industry. SIIG products can be found in computer retail stores, mail order catalogs, through major distributors, system integrators, and VARs in the Americas and the UK, and through e-commerce sites.
Product Name
Fixed LCD TV/Monitor Mount - 10" to 24"
Fixed LCD TV/Monitor Mount -10" to 24" is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered trademarks of SIIG, Inc. Other names used in this publication are for identification only and may be trademarks of their respective companies.
November, 2008 Copyright © 2008 by SIIG, Inc. All rights reserved.
Loading...