Page 1
1
Introducing the Cool SATA to USB 2.0
The Cool Dual SATA to USB 2.0 Docking is designed to
support USB equipped computers. This adapter
provides large capacity mobile storage using 3.5" or 2.5"
SATA hard disk drives through high-speed, hotswapping USB 2.0 interface.
Features and Benefits
• Two hard drive docking bays
• Supports Hi-Speed USB 2.0 port
• Supports SATA I/II (SATA 150/300)
• Supports 2.5" and 3.5" hard drive
• Plug and Play, no additional drivers needed
• Supports USB hot-swap and hot-plug
System Requirements
PC:
• Pentium® or equivalent computer with an available
USB port (USB 2.0 recommended)
• Windows® 2000 / XP (32-/64-bit) / Server 2003 &
2008 (32-/64-bit) / Vista (32-/64-bit)
Mac
®
:
• An available USB port (USB 2.0 recommended)
• Mac OS® X v10.4.8 or higher
Cool Dual SATA to
USB 2.0 Docking
Quick Installation Guide
04-0523A
Page 2
2
Package Contents
• Cool Dual SATA to USB 2.0 Docking
• Switching power adapter
• USB 2.0 cable (type A to type B)
• Quick Installation Guide
Layout
Note: You cannot use one hard drive in both
platforms, Windows and Mac. It is not supported
Figure 1. Front Layout
Figure 2: Back Layout
SATA Drive Slot
LED (Two LED's stay on
while the unit is on)
On/Off Switch
HDD LED (One LED per HDD;
LED flashes while transfering data)
USB Connector
Power Adapter Jack
Page 3
3
Hardware Installation
1. Make sure the SATA connectors are in alignment.
Gently insert the SATA hard drive into the SATA
drive slot.
2. Plug the included switching power adapter into
the Cool Dual SATA to USB 2.0 Docking power
adapter jack, then plug the switching power adapter
into a reliable power source.
3. Use the USB 2.0 cable to plug the Cool Dual SATA
to USB 2.0 Docking into the computer.
4. Switch on the Cool Dual SATA to USB 2.0 Docking,
make sure that the 3 blue Power LEDs are lit.
Note: Do not insert or remove a hard drive when
the unit is powered on.
Go to Driver Installation below to complete the
installation.
Driver Installation
Windows and Mac operating systems will automatically
detect and install drivers for the Cool Dual SATA to USB
2.0 Docking. No additional driver installation is needed.
Note: In order to get high speed USB 2.0
performance, make sure your USB 2.0 controller
has the correct drivers installed.
Page 4
4
Using the Cool Dual SATA to USB 2.0
Windows
One drive icon for each inserted SATA hard drive will
appear in My Computer when the converter is plugged
into a USB port. The drive(s) act just like a conventional
hard drive in your system.
Note: Be careful not to touch the hard drive while
in use. It will be warm.
Disconnecting From The Computer
Important: Do not insert or remove a hard drive while
the Cool Dual SATA to USB 2.0 Docking is powered on.
Before unplugging the Cool Dual SATA to USB 2.0 Docking
from the computer, it must first be stopped, by using
Windows' Safely Remove Hardware utility. Follow the
steps below for your version of Windows. The same
rule applies when turning off the Cool Dual SATA to USB
2.0 Docking. Not following the instructions may result in data
corruption or damage to the hard drive.
Windows 2000
1. Verify that the HDD LED(s) are OFF before
proceeding.
2. Double click the Unplug or Eject Hardware icon
located in the system tray.
3. Highlight USB Mass Storage Device, click Stop.
4. Click OK, click OK again, then Close.
5. You can now unplug or turn off the Cool Dual SATA
to USB 2.0 Docking.
Page 5
5
Windows XP/Server 2003 & 2008
1. Verify that the HDD LED(s) are OFF before
proceeding.
2. Double click the Safely Remove Hardware icon
located in the system tray.
3. Highlight USB Mass Storage Device, click Stop,
OK then Close.
4. You can now unplug or turn off the Cool Dual SATA
to USB 2.0 Docking.
Windows Vista™
1. Verify that the HDD LED(s) are OFF before
proceeding.
2. Double click the Unplug or Eject Hardware icon
located in the system tray.
3. Highlight USB Mass Storage Device, click Stop.
4. Click OK, click OK again, then Close.
5. You can now unplug or turn off the Cool Dual SATA
to USB 2.0 Docking.
Mac
One drive icon for each inserted SATA hard drive will
appear on the desktop when the Cool Dual SATA to USB
2.0 Docking is plugged into a USB port. The drive(s) act
just like a conventional hard drive in your system.
Disconnecting From The Computer
Before unplugging the Cool Dual SATA to USB 2.0 Docking
from the computer, drag the drive icon(s) into the
Trashcan and wait for the confirmation box. The same
rule applies when turning off the Cool Dual SATA to USB
2.0 Docking. Not following these instructions may result in
data corruption or damage to the hard drive.
Page 6
6
Blank Page
Page 7
7
Technical Support and Warranty
QUESTIONS? SIIG’s Online Support has answers! Simply visit our
web site at www.siig.com and click Support. Our online support
database is updated daily with new drivers and solutions. Answers
to your questions could be just a few clicks away. You can also submit
questions online and a technical support analysts will promptly
respond.
SIIG offers a 2-year manufacturer warranty with this product. Please
see our web site for more warranty details. If you encounter any
problems with this product, please follow the procedures below.
A) If it is within the store's return policy period, please return the
product to the store where you purchased from.
B) If your purchase has passed the store's return policy period, please
follow these steps to have the product repaired or replaced.
Step 1: Submit your RMA request.
Go to www.siig.com, click Support, then RMA to submit a
request to SIIG RMA. If the product is determined to be
defective, an RMA number will be issued.
Step 2: After obtaining an RMA number, ship the product.
• Properly pack the product for shipping. All software, cable(s)
and any other accessories that came with the original package
must be included.
• Clearly write your RMA number on the top of the returned
package. SIIG will refuse to accept any shipping package, and
will not be responsible for a product returned without an
RMA number posted on the outside of the shipping carton.
• You are responsible for the cost of shipping. Ship the product
to the following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA #:
• SIIG will ship the repaired or replaced product via Ground
in the U.S. and International Economy outside of the U.S. at
no cost to the customer.
Page 8
Cool Dual SATA to USB 2.0 Docking is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered
trademarks of SIIG, Inc. Microsoft, Windows and Windows Vista are either registered trademarks
or trademarks of Microsoft Corporation in the United States and/or other countries. Pentium is a
registered trademark of Intel Corporation. Mac and Mac OS are registered trademarks of Apple, Inc.
Other names used in this publication are for identification only and may be trademarks of their
respective companies.
December, 2008 Copyright © 2008 by SIIG, Inc. All rights reserved.
About SIIG, Inc.
Founded in 1985, SIIG, Inc. is a leading computer upgrade
manufacturer of I/O connectivity products, including PCIe, PCI &
ISA serial and parallel ports, USB, Serial ATA & UltraATA controllers,
FireWire (1394a/b), networking, sound cards, and other accessories.
SIIG is the premier one-stop source of upgrades.
SIIG products offer comprehensive user manuals, many user-friendly
features, and are backed by an extensive manufacturer warranty.
High-quality control standards are evident by the overall ease of
installation and compatibility of our products, as well as one of the
lowest defective return rates in the industry. SIIG products can be
found in computer retail stores, mail order catalogs, through major
distributors, system integrators, and VARs in the Americas and the
UK, and through e-commerce sites.
PRODUCT NAME
Cool Dual SATA to USB 2.0 Docking
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCC COMPLIANCE STATEMENT:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
Ph: 510-657-8688
Loading...