1
Parallel PCI 1P
Quick Installation Guide
04-0358D
Introducing the Parallel PCI 1P
The Parallel PCI 1P high-speed parallel card provides
one additional parallel port to your system. Depending
on the model purchased, this board will fit into either
Full or Low Profile chassis.
Features and Benefits
• Conforms to PCI v2.2 Plug and Play
• Supports 32-/64-bit, 3.3V/5V PCI and PCI-X slots
• Full support for Windows-based software
• Reduces CPU load and improves system
performance dramatically
• Supports EPP/ECP, BPP (bi-directional), SPP
(standard) parallel port modes
System Requirements
• Pentium® or equivalent computer with an available
32-/64-bit PCI or PCI-X slot
• Windows ® 7 (32-/64-bit) / Vista (32-/64-bit) / XP
(32-/64-bit) / Server 2003 & 2008 (32-/64-bit) /
2000 / NT 4.0 / ME / 98SE / 98 / 95
Package Contents
• Parallel PCI 1P board
• Low profile bracket (for Dual Profile PCI-1P only)
• Driver CD
• Quick installation guide
2
Parallel Port
Layout
Depending on the model purchased, the bracket mounted
on your board may vary from the image displayed.
Figure 1. Layout
Hardware Installation
General instructions for installing the card are provided
below. Since the design of computer cases and
motherboards vary, refer to your computer’s reference
manual for further information, if needed.
Static Electricity Discharge may permanently damage
your system. Discharge any static electricity build up in
your body by touching your computer’s case for a few
seconds. Avoid any contact with internal parts and
handle cards only by their external edges.
1. Turn OFF the power to your computer and any
other connected peripheral devices.
2. Unplug the power cord from the back of the
computer.
Full profile bracket
3
3. Remove your computer cover.
4. Remove the slot bracket from an available PCI slot.
5. To install the card, carefully align the card's bus
connector with the selected PCI slot on the
motherboard. Push the board down firmly, but
gently, until it is well seated.
6. Replace the slot bracket holding screw to secure the
card.
7. Replace the computer cover and reconnect the power
cord.
Driver Installation
This section provides information on how to install the
Parallel PCI 1P drivers.
Windows 7 (32-/64-bit)
1. Install the board and boot up Windows.
Note: Windows 7 will automatically search
preconfigured driver folders for the proper driver,
this process may take several minutes to complete.
Do not interrupt this process.
2. Right click Computer, click Manage, click Device
Manager.
3. Insert the driver CD. Right click PCI Parallel Port,
click Update Driver Software.
4. Click Browse my computer for driver software.
5. Type D:, then click Next. (Change D: to match your
CD/DVD-ROM drive letter)
6. At Windows has successfully updated your driver
software, click Close to complete the installation.
4
Windows Vista™ (32-/64-bit)
1. Install the board and boot up Windows.
2. At the Found New Hardware window, insert the
driver CD, click Locate and install driver software
(recommended), then click Continue.
3. Click Don't search online.
4. Click Next, then click Close to complete the
installation.
Windows XP (32-bit) / Server 2003 (32-bit)
1. Install the board and boot up Windows.
2. At the Found New Hardware Wizard, insert the
driver CD.
For XP w/SP1 or earlier / Server 2003: go to step #2.
For XP w/SP2 or later / Server 2003 wSP1 or later: select
No, not this time, click Next.
3. Select Install the software automatically
(Recommended, then click Next.
4. Click Finish.
5. Restart Windows to complete the installation.
Windows XP (64-bit) / Server 2003 (64-bit)
1. Install the board and boot up Windows.
2. At the Found New Hardware Wizard, insert the
driver CD.
For XP w/SP1 or earlier / Server 2003: go to step #2.
For XP w/SP2 or later / Server 2003 wSP1 or later: select
No, not this time, click Next.
3. Select Install the software automatically
(Recommended, then click Next.
5
4. Click Continue Anyway, then click Finish.
5. Restart Windows to complete the installation.
Windows Server 2008 (32-bit)
1. Install the board and boot up Windows.
2. At the Found New Hardware Wizard, click Locate
and install driver software (recommended).
3. Insert the driver CD.
4. Click Don't search online.
5. Click I don't have the disc. Show me other options.
6. Click Browse my computer for driver software
(advanced).
7. Type D:, then click Next. (Change D: to match your
CD/DVD-ROM drive letter)
8. At The sofware for this device has been successfully
installed, click Close to complete the installation.
Windows Server 2008 (64-bit)
1. Install the board and boot up Windows.
2. At the Found New Hardware Wizard, click Locate
and install driver software (recommended).
3. Insert the driver CD.
4. Click I don't have the disc. Show me other options.
5. Click Browse my computer for driver software
(advanced).
6. Type D:, then click Next. (Change D: to match your
CD/DVD-ROM drive letter)
7. At The sofware for this device has been successfully
installed, click Close to complete the installation.
6
To Verify Windows 7 / Vista / XP / Server 2003 &
2008 Installation
1. Check in Device Manager to verify installation.
For Windows 7: Right click Computer, click Manage,
then click Device Manager.
For Windows Vista: Right click Computer, click
Manage, click Continue, then click Device Manager.
For Windows XP / Server 2003: Right click My
Computer, click Manage, click Device Manager.
For Windows Server 2008: Right click Computer, click
Manage, double click Diagnostics, then click Device
Manager.
2. Click on the + (plus sign) in front of Ports (COM &
LPT), and a SIIG CyberPro Parallel port should be
displayed.
Windows 2000
1. Install the board and boot up Windows.
2. At the Found New Hardware Wizard, click Next.
3. Select Search for a suitable driver for my device
(recommended), then click Next.
4. Select Specify a location, uncheck the other options
and click Next.
5. Insert the driver CD, type in D:\2000, then click OK.
(Change D: to match your CD/DVD-ROM drive
letter)
6. Check Install one of the other drivers, click Next.
7. Select SIIG CyberPro 1P PCI board(Windows 2000),
click Next.
8. Click Finish.
9. Restart Windows to complete the installation.
7
To Verify Windows 2000 Installation
1. Right click My Computer, click Manage, then click
Device Manager.
2. Click on the + (plus sign) in front of Ports (COM &
LPT), and a SIIG CyberPro 1P PCI board should be
displayed.
Windows ME
1. At the Add New Hardware Wizard, select Specify
the location of the driver (Advanced), click Next.
2. Check Specify a location, uncheck the other box,
insert the driver CD, type in D:\Me, then click Next.
(Change D: to match your CD/DVD-ROM drive
letter)
3. Click Next, then Finish.
4. Restart Windows to complete the installation.
Windows 98 / 98SE
1. At the Add New Hardware Wizard, click Next.
2. Select Search for the best driver for your device.
(Recommended), then click Next.
3. Select Specify a location, uncheck the other boxes,
insert the driver CD, type in D:\9x, then click Next.
(Change D: to match your CD/DVD-ROM drive
letter)
4. Click Next, then Finish. If prompted, at the Insert
Disk box click OK. Insert your Windows 98
Installation CD-ROM then click OK.
5. Restart Windows to complete the installation.
8
Windows 95
1. At the Update Device Driver Wizard, click Next.
2. Insert the driver CD, and click Other Locations.
3. Type in D:\9x, click OK, then Finish. (Change D: to
match your CD-ROM drive letter)
4. From the Insert Disk window, click OK. When the
Copying Files dialog box appears, type in
D:\9x, then click OK. (Change D: to match your
CD/DVD-ROM drive letter)
5. Restart Windows to complete the installation.
To Verify Windows ME / 98SE / 98 / 95 Installation
1. From the Windows desktop, double click My
Computer, Control Panel, System, then click Device
Manager.
2. Double click Ports (COM & LPT), ECP Printer
Port... and SIIG CyberPro 1P PCI board should be
displayed.
Windows NT 4.0
1. From the desktop click Start, then Run. Insert the
driver CD.
2. Type in D:\NT4\Install_Parallel.exe, then click OK.
(Change D: to match your CD/DVD-ROM drive
letter)
3. At the Welcome window, click Next.
4. Choose Install, then click Next.
5. Click Yes, then click Exit.
6. Click Yes to restart to complete the installation.
9
To Verify Windows NT 4.0 Installation
1. Click Start, Programs, Administrative Tools, then
Windows NT Diagnostics.
2. Click Resources tab, SIIGpar should be displayed.
10
Blank Page
11
Technical Support and Warranty
QUESTIONS? SIIG’s Online Support has answers! Simply visit our
web site at www.siig.com and click Support. Our online support
database is updated daily with new drivers and solutions. Answers
to your questions could be just a few clicks away. You can also submit
questions online and a technical support analysts will promptly
respond.
SIIG offers a lifetime manufacturer warranty with this product. Please
see our web site for more warranty details. If you encounter any
problems with this product, please follow the procedures below.
A) If it is within the store's return policy period, please return the
product to the store where you purchased from.
B) If your purchase has passed the store's return policy period, please
follow these steps to have the product repaired or replaced.
Step 1: Submit your RMA request.
Go to www.siig.com, click Support, then RMA to submit a
request to SIIG RMA. If the product is determined to be
defective, an RMA number will be issued.
Step 2: After obtaining an RMA number, ship the product.
• Properly pack the product for shipping. All software, cable(s)
and any other accessories that came with the original package
must be included.
• Clearly write your RMA number on the top of the returned
package. SIIG will refuse to accept any shipping package, and
will not be responsible for a product returned without an
RMA number posted on the outside of the shipping carton.
• You are responsible for the cost of shipping. Ship the product
to the following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA #:
• SIIG will ship the repaired or replaced product via Ground
in the U.S. and International Economy outside of the U.S. at
no cost to the customer.
Parallel PCI 1P is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered trademarks of SIIG, Inc.
Microsoft, Windows and Windows Vista are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries. Pentium is a registered trademark of Intel
Corporation. Other names used in this publication are for identification only and may be trademarks
of their respective companies.
October, 2009 Copyright © 2009 by SIIG, Inc. All rights reserved.
About SIIG, Inc.
Founded in 1985, SIIG, Inc. is a leading computer upgrade manufacturer
of I/O connectivity products, including PCIe, PCI & ISA serial and
parallel ports, USB, Serial ATA & UltraATA controllers, FireWire
(1394a/b), networking, sound cards, and other accessories. SIIG is the
premier one-stop source of upgrades.
SIIG products offer comprehensive user manuals, many user-friendly
features, and are backed by an extensive manufacturer warranty.
High-quality control standards are evident by the overall ease of
installation and compatibility of our products, as well as one of the
lowest defective return rates in the industry. SIIG products can be
found in computer retail stores, mail order catalogs, through major
distributors, system integrators, and VARs in the Americas and the
UK, and through e-commerce sites.
PRODUCT NAME
Parallel PCI 1P
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCC COMPLIANCE STATEMENT:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
Phone: 510-657-8688
Loading...