SIIG L734, L732, L733, L704 User Manual
Ultra-Thin LED/LCD TV Mount - 32" to 55"
Installation Instructions
Ultra-Thin LED/LCD TV Wall Mount
Material: 2.0mm Cold Rolled Steel Plate
TV Size: 32" - 55”
Max load capacity: 121lbs/55kg
Wall distance: 0.43/11mm
Bubble level included
Universal Mounting Pattern
IMPORTANT: If you don't understand the installation instructions, please consult an
installation specialist
04-0541B
1
Caution
INSTALLATION AND OPERATING INSTRUCTIONS
Prior to the installation of this product, the installation instructions should be read and completely understood.
The installation instructions must be read to prevent personal injury and property damage. Keep these
installation instructions in an easily accessible location for future reference.
CAUTION: The maximum load capacity is 121 lbs. Use with products exceeding the maximum load capacity may
cause serious injury. See apparatus instructions.
Recommended mounting surfaces: wood stud and solid-flat concrete. If the mount is to be installed on any
surface other than wood studs or concrete, use suitable hardware (not included but commercially available).
Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to do so could
result in damage to the display and/or damage to the mounting surface.
Do not install near heater, fireplace, air conditioning, in direct sunlight, or any other heat producing source.
Failure to do so may result in damage to the display and could increase the risk of fire.
The wall structure must be capable of supporting at least the maximum load capacity as indicated. If not, the
wall must be reinforced. Proper installation procedure by yourself or a qualified service technician, as outlined in
the installation instructions, must be adhered to. Failure to do so could result in serious personal injury.
When mounting to a wall that contains wood studs, confirm dead center of the wood stud prior to installation, it is
recommended that the wood studs be a minimum of 16" apart.
It is recommended that two people perform the installation. Injury and/or damage can result from dropping or
mishandling the display.
Hardware Kit
(×4) M5×16 screw
AG
(×4) M6×16 screw
B H-1
(×4) M8×16 screw
C H-2
(×4) M5×35 screw (×4) M8×80 bolt
DI
(×4) M6×35 screw (×4) Concrete anchor
EJ
(×4) M8×35 screw (×4) M8 spacer
FK
L
(×4) M6 washer
(x4) M5 washer
(×1) Bubble level
(x2) Sponge sticker
2
Tools Required
Phillips head screw driver
1
Stud finder for drywall installation
2
Level
3
1/2" socket & socket wrench and/or 1/2" open-end wrench
4
Drill, 3/16" (5mm) drill bit for wood stud installation and 1/2" (12mm) masonry drill bit for concrete/brick
5
installation
Step 1: Wall Plate Installation
a) Wood Stud Installation
NOTE: When mounting to wood studs, the two wood studs must be a minimum of 16" apart.
Use a high-quality electronic stud finder (commercially available) to locate dead center of two studs and mark
1
their locations with a pencil.
Attach the bubble level (H-2) to the wall plate and with the help of an assistant ensure the wall plate is level,
2
position the wall plate against the wall in the desired mounting location.
3
Mark the right and the left positions of the small horizontal slots that are in alignment with the studs.
4
You should mark two positions total.
5
Pre-drill a 3/16" hole to a depth of approximately 3" in the wall stud at each marked location.
6 Place the wall plate against the wall and line up the mounting slots with the drilled holes. Check the bubble level
to verify that the wall plate is level.
7
For each location, insert bolt (I) into the wall.
8
Tighten the bolt with the 1/2" socket or 1/2" open-end wrench by turning clockwise until tight.
CAUTION: Do not over-tighten bolts - doing so may cause unnecessary damage to the wall.
CAUTION: Do not release the wall plate until it is properly mounted and secured to the wall.
3
Loading...