SIIG HDMI to VGA & Audio Converter Scaler Installation Manual

Page 1
HDMI to VGA & Audio
Converter Scaler
Installation Guide
Introduction
The HDMI to VGA & Audio Converter Scaler converts digital HDMI to VGA and stereo audio.
Supports PC resolution up to WUXGA (1920x1200@60Hz)
Supports de-interlacing & video H/V mirror
Active video area adjustment and over/ under scanning adjustable
Supports noise reduction and video enhancement
Stereo S/PDIF and analog Stereo audio output
OSD control interface and IR remote control
Metal housing with wall mount capability
04-0916A
1
Page 2
Package Contents
HDMI to VGA & Audio Converter Scaler
Screw Kit and 4 rubber pads
Power adapter (5V/2A)
IR remote control
Software CD and Installation guide
Layout
IR Sensor
DIP Switch
Figure 1: Front Layout
LED Indicator
Push Buttons
DIP Switch: F/W ( ) for firmware update; NORMAL ( ) for normal operation
LED Indicator: The upper LED lights up when powered on; the lower LED lights up when signal is detected
IR sensor: Receives the IR commands from the included IR remote control
Push Buttons (from left to right): Down, Up, Menu/Enter. See page 5 for more details.
2
Page 3
Power Jack
S/PDIF Audio Out
Stereo Audio OutMini USB port
Figure 2: Rear Layout
VGA Output
HDMI Input
Power Jack: Plug in the power adapter here
Mini USB port: Connects to a USB port of a
computer to control the Scaler via software.
Stereo Audio Out: Connects to analog stereo
audio speakers
S/PDIF Audio Out: Connects to digital
S/PDIF speakers via RCA connector
VGA Output: Connects to a VGA display
HDMI IN: Connects to an HDMI source
Hardware Installation
1. Power off all devices, including the source
device and display.
2. Connect the monitor's VGA input to the
Scaler's VGA Output.
3. Connect the stereo audio speaker to the
Scaler's Stereo Audio Out, if needed.
3
Page 4
4. Connect the S/PDIF audio speaker to the
Scaler's S/PDIF Audio Out, if needed.
5. Connect an HDMI cable (cable not included)
to your HDMI source, then connect the other end to the Scaler's HDMI Input.
6. Plug the included power adapter into the
Scaler's Power Jack, then plug it into a reliable power outlet.
7. Power on all audio/video units connected
to the Scaler. The Scaler is ready to use.
Application
3.5mm audio
cable
HDMI source (computer,
TV, DVD player, etc)
HDMI cable
VGA display
VGA cable
S/PDIF
cable
Speakers (S/PDIF (RCA)
4
or 3.5mm stereo)
Figure 3: Application
Page 5
Scaler Control
The Scaler can be controlled by the front panel push buttons, IR remote control or Scaler software.
Push ButtonsIR Sensor
Push Button
Press the MENU button to open the selection menu, see Figure 4. Use the UP or DOWN button to select the setting you want to change. Click Menu button to display the menu options.
Figure 4
5
Page 6
IR Remote Control
Point the remote control at the Scaler's IR sensor.
Figure 5
Scaler Software
Connect the Scaler's mini USB port to your computer's USB port using a USB cable (cable not included). Insert the included software CD to your computer, double click the Setup file and follow the on-screen instructions to install the driver. After completing the installation, double click the Scaler Software icon to launch the software.
6
Page 7
4 5 2
1
3
6
7
8
Figure 6: Scaler Software Main Menu
1. COM Port search button:
Click the button to search for available COM ports.
2. COM Port selection menu:
9
Select the Scaler's COM port from the drop down menu.
3. Output Setup button:
Select the output resolution, output mode, default pattern, and the EDID audio channel from the drop down menu, then click Apply to enforce these changes.
7
Page 8
4. Image button: Click the Image button to set up your
preferred display contrast, brightness, saturation, hue and other related values.
Figure 7
8
Figure 8
Page 9
5. Adjustment Button: Click the Adjustment Button to adjust the
screen size, change the aspect ratio or other display settings.
Figure 9
6. System Button: Click System button, then click Get to view
the current input resolution, or click Factory Reset to set the Scaler back to the default settings. The firmware can also be updated here. Please refer to the instructions on page 11.
Figure 10
9
Page 10
7. Resolution info: Displays the input/output port and screen
resolution information.
8. Refresh button: After making any changes, click this button
to view your new configuration.
9. Output Quick Selection: Shortcuts to some commonly used settings: (1) Aspect ratio: Click to switch aspect ratio
between 4:3 and 16:9. (2) Freeze: Click to freeze the display. The
display will remain still until you click the Freeze button again.
(3) Blank: Click to disable the display. Click the Blank button again to return to normal operation.
(4) 1080p60, 1080i60, 720p60, 680p60: Click to change the output resolution.
10
Page 11
Firmware Update
Note: If the Scaler Software is not installed, go to Scaler Software on page 6 now and follow the
instructions to install it. Otherwise, follow the instruction below to update the firmware.
1. Connect the Scaler to your computer using
a USB cable (cable not included), double click the Scaler software icon.
2. Enter the Scaler software main menu, select
a COM port and click Refresh to make the connection.
3. Click System button, then click Firmware
Update.
4. Click Load file, select the firmware file.
5. Set the DIP Switch up to F/W, unplug and
plug the Scaler's power adapter.
6. Click Burn. Wait for the firmware update
process to complete.
7. Power off the Scaler, unplug the USB cable
from the Scaler, then set the DIP Switch back to Normal. The firmware update process is now complete.
11
Page 12
Appendix
OSD menu
Refer to the OSD menu below for the full list of all the selectable viewing options:
12
Page 13
13
Page 14
Table 1
Supported Video Resolution
14
Table 2
Page 15
Technical Support and Warranty
QUESTIONS? SIIGs Online Support has answers! Simply visit our web site at
www.siig.com and click Support. Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit questions online and a technical support analyst will promptly respond.
SIIG offers a 3-year manufacturer warranty with this product. This warranty covers the original purchaser and guarantees the product to be free of any defects in materials or workmanship for three (3) years from the date of purchase of the product.
SIIG will, at our discretion, repair or replace (with an identical product or product having similar features and functionality) the product if defective in materials or workmanship. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Please see our web site for more warranty details.
If you encounter any problems with this product, please follow the procedures below. A) If it is within the store's return policy period, please return the product to the store
where you purchased from.
B) If your purchase has passed the store's return policy period, please follow the steps below to have the product repaired or replaced.
Step 1: Submit your RMA request. Go to www.siig.com, click Support, then REQUEST A PRODUCT REPLACEMENT
to submit a request to SIIG RMA or fax a request to 510-657-5962. Your RMA request will be processed, if the product is determined to be defective, an RMA number will be issued.
Step 2: After obtaining an RMA number, ship the product.
Properly pack the product for shipping. All accessories that came with the original package must be included.
Clearly write your RMA number on the top of the returned package. SIIG will refuse to accept any shipping package, and will not be responsible for a product returned without an RMA number posted on the outside of the shipping carton.
You are responsible for the cost of shipping to SIIG. Ship the product to the following address:
SIIG, Inc. 6078 Stewart Avenue Fremont, CA 94538-3152, USA RMA #:
SIIG will ship the repaired or replaced product via Ground in the U.S. and International Economy outside of the U.S. at no cost to the customer.
15
Page 16
About SIIG, Inc.
Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity solutions (including Serial ATA and Ultra ATA Controllers, FireWire, USB, and legacy I/O adapters) that bridge the connection between Desktop/ Notebook systems and external peripherals. SIIG continues to grow by adding A/V and Digital Signage connectivity solutions to our extensive portfolio. SIIG products offer comprehensive user manuals, many user-friendly features, and are backed by an extensive manufacturer warranty. High quality control standards are evident by the overall ease of installation and compatibility of our products, as well as one of the lowest defective return rates in the industry. SIIG products can be found in computer retail stores, mail order catalogs, through major distributors, system integrators, and VARs in the Americas and the UK, and through e-commerce sites.
PRODUCT NAME
HDMI to VGA & Audio Converter Scaler
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCC COMPLIANCE STATEMENT:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE SIIG, Inc.
6078 Stewart Avenue Fremont, CA 94538-3152, USA Phone: 510-657-8688
HDMI to VGA & Audio Converter Scaler is a trademark of SIIG, Inc. SIIG and SIIG logo are registered trademarks of SIIG, Inc. All other trademarks are the property of their respective owners
November, 2013 Copyright © 2013 by SIIG, Inc. All rights reserved
Loading...