SIIG eSATA II PCIe i/e Quick Installation Manual

1
eSATA II PCIe i/e
Quick Installation Guide
04-0395C
Introducing the eSATA II PCIe i/e
The eSATA II PCIe i/e is an ultra high-speed dual channel Serial ATA Generation 2 controller for use in PCI Express enabled systems.
Features and Benefits
Compliant with PCI Express Base Specification 1.0a
Compliant with Serial ATA 1.0a specification with support for full complement of SATA II optional features
PCI Express 1-lane (x1) SATA II adapter works with PCI Express slots with different lane width
Installs in any available PCI Express slot and supports data transfer rates up to 3.0Gbps (300MBps)
Spare enhanced low profile bracket is included to work in low profile chassis
Supports Native Command Queuing (NCQ), Non­zero offsets NCQ, and Out-of-order date delivery NCQ
Independent command fetch, scatter/gather, and command execution
Supports hard disk hot-plugging
System Requirements
PCI Express-enabled system with an available PCI Express slot
Windows® 2000 / XP (32-/64-bit) / Server 2003 & 2008 (32-/64-bit) / Vista (32-/64-bit)
2
Package Contents
eSATA II PCIe i/e board and spare enhanced low profile bracket
SATA data cable and SATA 15-pin power cable
Driver CD and Quick Installation Guide
Board Layout
Figure 1. eSATA II PCIe i/e Board Layout
Hardware Installation
General instructions for installing the card are provided below. Since the design of computer cases and motherboards vary, refer to your computer’s reference manual for further information, if needed.
Static electricity discharge may permanently damage your system. Discharge any static electricity build up in your body by touching your computer’s case for a few seconds. Avoid any contact with internal parts and handle cards only by their external edges.
1. Turn OFF the power to your computer and any other connected peripheral devices.
2. Unplug the power cord from the computer.
External SATA Connector
Internal SATA Connector
Hard Disk LED Pins (Connect horizontally)
HDD Activity LED
3
3. Remove the computer cover.
4. Remove the slot bracket from an available PCIe slot.
5. To install the card, carefully align the card's bus connector with the selected PCIe slot on the motherboard. Push the board down firmly, but gently, until it is well seated.
6. Replace the slot bracket holding screw to secure the card.
Device Connection
The eSATA II PCIe i/e supports one internal and one external Serial ATA hard disk drive.
Internal Serial ATA port
1. Install the hard disk drive into the chassis.
2. Connect the Serial ATA hard disk drive to the system power supply using the SATA 15-pin power cable.
3. Connect one end of the SATA data cable to the hard disk drive.
Figure 2. Hard disk drive connections
Note: For hard disk drives with both SATA power
connector and legacy 5-pin connector, use either the SATA power connector or the legacy 5-pin power connector. Using both power connectors at the same time will damage the hard disk drive.
SATA data cable
SATA 15-pin power cable
4
4. Attach the other end of the SATA data cable to the
internal Serial ATA connector.
5. Replace the computer cover and reconnect the power cord.
External Serial ATA port
External Serial ATA hard disk drives should come with their own accessories. In most cases, you just need to power up the external drive and connect it to the external port. For more information, please refer to the external device's manual.
Driver Installation
This section provides information on how to install the eSATA II PCIe i/e drivers.
Windows 2000
New Installation
A new installation of Windows 2000 requires a floppy disk for the driver installation. To make this floppy disk, copy the contents of the Floppy folder, found on the driver CD, onto a blank floppy disk then follow the directions below.
1. Install the board and follow Microsoft procedures to install Windows accordingly.
2. Restart your system if prompted during Windows installation, otherwise, go directly to step 3.
3. At the Windows 2000 Setup screen, press F6 to install the driver.
4. Insert the driver diskette. Press S, then press Enter.
5. Select Silicon Image SiI 3132... Controller for Windows 2000 and press Enter.
5
6. Press Enter to continue and follow the on-screen instructions to complete the installation.
Existing Installation
1. Install the board and boot up Windows.
2. At the Found New Hardware Wizard, click Next.
3. Select Search for a suitable driver for my device (recommended) and click Next.
4. Insert the driver CD, check CD-ROM drives, uncheck the other boxes, and click Next. Click Next again to continue.
5. Click Finish and restart Windows to complete the driver installation.
Windows XP (32-bit) / Server 2003 (32-bit)
New Installation
A new installation of Windows XP/Server 2003 requires a floppy disk for the driver installation. To make this floppy disk, copy the contents of the Floppy folder, found on the driver CD, onto a blank floppy disk then follow the directions below.
1. Install the board and follow Microsoft procedures to install Windows accordingly.
2. Restart your system if prompted by Windows installation, otherwise, go directly to step 3.
3. At the Windows Setup screen, press F6 to install the driver.
4. Insert the driver diskette. Press S then press Enter.
5. Select Silicon Image Sil 3132... Controller for Windows XP/Server 2003 and press Enter.
6. Press Enter to continue and follow on-screen instructions to complete Windows installation.
Loading...
+ 11 hidden pages