Page 1
1
DP 1-Port ECP/EPP
Parallel PCIe
Quick Installation Guide
04-0718B
Introduction
The DP 1-Port ECP/EPP Parallel PCIe high-speed
parallel card provides one additional parallel
port to your PCIe Express enabled system.
Key Features and Benefits
• PCI Express 1-lane (x1) adapter that works
in any PCI Express slot
• Dual Profile design to work with standard
height and low profile chassis
• Compliant with PCI Express Base
Specification, Revision 1.1
• Supports ECP, EPP, and SPP parallel port
modes
Page 2
2
Figure 1: Board Layout
Parallel Port
System Requirements
• PCI Express enabled system with an
available PCI Express slot
• Windows
®
8 (32-/64-bit) / 7 (32-/64-bit) /
Vista (32-/64-bit) / XP (32-/64-bit) / Server
2003 & 2008 (32-/64-bit) / Server 2008 R2
/ 2000
Package Contents
• DP 1-Port ECP/EPP Parallel PCIe adapter
• Spare enhanced low-profile bracket
• Driver CD
• Quick installation guide
Layout
Page 3
3
Hardware Installation
General instructions for installing the card are
provided below. Since the design of computer
cases and motherboards vary, refer to your
computer’s reference manual for further
information, if needed.
Static Electricity Discharge may permanently
damage your system. Discharge any static
electricity build up in your body by touching your
computer’s case for a few seconds. Avoid any
contact with internal parts and handle cards
only by their external edges.
Note: for low profile chassis, remove the
standard height bracket and install the
enhanced low-profile bracket now.
1. Turn OFF the power to your computer and
any other connected peripheral devices.
2. Unplug the power cord from the computer.
3. Remove the computer cover.
4. Remove the slot bracket from an available
PCI Express slot.
Page 4
4
5. To install the card, carefully align the card's
bus connector with the selected PCI Express
slot on the motherboard. Push the board
down firmly, but gently, until it is well
seated.
6. Replace the slot bracket's holding screw to
secure the card.
7. Replace the computer cover and reconnect
the power cord.
Driver Installation
Please make sure the board is installed before
proceeding with driver installation.
Windows 8 (32-/64-bit) / 7 (32-/64-bit)
1. Insert the driver CD, close the AutoPlay
box if displayed.
2. Click Windows key and R, type
D:\setup.exe, click OK. (Change D: to
match your CD/DVD-ROM drive letter)
3. At User Account Controls, click Yes.
Page 5
5
4. At the PLX OXPCIe95x RS-232 Serial/
Parallel PCIe Card Setup window, click
Install, then click Finish to restart the
computer.
Windows Vista (32-/64-bit)
1. Install the board and boot up Windows.
2. At the Found New Hardware Wizard, click
Cancel.
3. Insert the driver CD, close the AutoPlay
box if displayed.
4. Click Start, in the Start Search box, type
D:\setup.exe, press Enter. (Change D: to
match your CD/DVD-ROM drive letter)
5. At User Account Controls, click Allow.
6. At the PLX OXPCIe95x RS-232 Serial/
Parallel PCIe Card Setup window, click
Install, then click Finish to restart the
computer.
Page 6
6
Windows XP (32-/64-bit) / Server 2003 (32-/
64-bit)
1. Install the board and boot up Windows.
2. At the Found New Hardware Wizard, click
Cancel.
3. Insert the driver CD.
4. Click Start, then Run. Type D:\setup.exe,
click OK. (Change D: to match your CD/
DVD-ROM drive letter)
5. At the PLX OXPCIe95x RS-232 Serial/
Parallel PCIe Card Setup window, click
Install, then click Finish to restart the
computer.
Windows Server 2008 (32-/64-bit)
1. Install the board and boot up Windows.
2. At the Found New Hardware Wizard, click
Cancel.
3. Insert the driver CD, close the AutoPlay if
displayed.
4. Click Start, in the Start Search box, type
D:\setup.exe, press Enter. (Change D: to
match your CD/DVD-ROM drive letter)
Page 7
7
5. At the PLX OXPCIe95x RS-232 Serial/
Parallel PCIe Card Setup window, click
Install, then click Finish to restart the
computer.
Windows Server 2008 R2
1. Install the board and boot up Windows.
2. Insert the driver CD, close the AutoPlay
box if displayed.
3. Click Start, in the Search programs and
files box, type D:\setup.exe, press Enter.
(Change D: to match your CD/DVD-ROM
drive letter)
4. At the PLX OXPCIe95x RS-232 Serial/
Parallel PCIe Card Setup window, click
Install, then click Finish to restart the
computer.
Windows 2000
1. Install the board and boot up Windows.
2. At the Found New Hardware Wizard, click
Cancel.
3. Insert the driver CD.
Page 8
8
4. Click Start, then Run. Type D:\setup.exe,
click OK. (Change D: to match your CD/
DVD-ROM drive letter)
5. At the PLX OXPCIe95x RS-232 Serial/
Parallel PCIe Card Setup window, click
Install, then click Finish to restart the
computer.
To Verify Windows Installation
1. Check in Device Manager to verify
installation.
For Windows 8 / 7: Right click Computer,
click Manage, then click Device Manager.
For Windows Vista: Right click Computer,
click Manage, click Continue, then click
Device Manager.
For Windows XP / Server 2003 / 2000: Right
click My Computer, click Manage, click
Device Manager.
For Windows Server 2008 / Server 2008 R2:
Right click Computer, click Manage, double
click Diagnostics, click Device Manager.
Page 9
9
2. Click on the + (plus sign) in front of Ports
(COM & LPT), PCI Express ECP Parallel
Port (LPT...) should be displayed.
Changing Parallel Port Number
Some parallel port devices need a specific LPT in
order to work. If your parallel port device works
properly, do not change this setting.
1. From the Device Manager window double
click Ports (COM & LPT), then double click
PCI Express ECP Parallel Port (LPT...).
2. Click the Port Settings tab.
3. Click the down arrow next to the LPT Port
number box, then select a parallel port that
is not in use.
4. Click OK to save the changes, then close the
Device Manager.
Page 10
10
Blank Page
Page 11
11
Technical Support and Warranty
QUESTIONS? SIIG’s Online Support has answers! Simply visit our web site at
www.siig.com and click Support. Our online support database is updated daily with
new drivers and solutions. Answers to your questions could be just a few clicks away.
You can also submit questions online and a technical support analyst will promptly
respond.
SIIG offers a 2-year manufacturer warranty with this product. This warranty covers the
original purchaser and guarantees the product to be free of any defects in materials or
workmanship for two (2) years from the date of purchase of the product.
SIIG will, at our discretion, repair or replace (with an identical product or product
having similar features and functionality) the product if defective in materials or
workmanship. This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state. Please see our web site for more warranty details.
If you encounter any problems with this product, please follow the procedures below.
A) If it is within the store's return policy period, please return the product to the store
where you purchased from.
B) If your purchase has passed the store's return policy period, please follow the steps
below to have the product repaired or replaced.
Step 1: Submit your RMA request.
Go to www.siig.com, click Support, then REQUEST A PRODUCT REPLACEMENT
to submit a request to SIIG RMA or fax a request to 510-657-5962. Your RMA request
will be processed, if the product is determined to be defective, an RMA number will
be issued.
Step 2: After obtaining an RMA number, ship the product.
• Properly pack the product for shipping. All accessories that came with the
original package must be included.
• Clearly write your RMA number on the top of the returned package. SIIG will
refuse to accept any shipping package, and will not be responsible for a product
returned without an RMA number posted on the outside of the shipping
carton.
• You are responsible for the cost of shipping to SIIG. Ship the product to the
following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA #:
• SIIG will ship the repaired or replaced product via Ground in the U.S. and
International Economy outside of the U.S. at no cost to the customer.
Page 12
PRODUCT NAME
DP 1-Port ECP/EPP Parallel PCIe
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B
OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCC COMPLIANCE STATEMENT:
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
Phone: 510-657-8688
About SIIG, Inc.
Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity
solutions (including Serial ATA and Ultra ATA Controllers, FireWire, USB,
and legacy I/O adapters) that bridge the connection between Desktop/
Notebook systems and external peripherals. SIIG continues to grow by adding
A/V and Digital Signage connectivity solutions to our extensive portfolio.
SIIG products offer comprehensive user manuals, many user-friendly features,
and are backed by an extensive manufacturer warranty. High quality control
standards are evident by the overall ease of installation and compatibility of
our products, as well as one of the lowest defective return rates in the industry.
SIIG products can be found in computer retail stores, mail order catalogs,
through major distributors, system integrators, and VARs in the Americas and
the UK, and through e-commerce sites.
DP 1-Port ECP/EPP Parallel PCIe is a trademark of SIIG, Inc. SIIG and the SIIG logo are
registered trademarks of SIIG, Inc. Microsoft and Windows are registered trademarks of
Microsoft Corporation. All other names used in this publication are for identification only
and may be trademarks of their respective owners.
May, 2013 Copyright © 2013 by SIIG, Inc. All rights reserved.
Loading...