1
Cyber PCI I/O
Quick Installation Guide
04-0201C
Introducing the Cyber PCI I/O
The Cyber PCI I/O high-speed serial and parallel I/O card family
provides a complete solution for serial and parallel device
connections. It provides 16550/16650/16850 UART serial port(s)
which supports data transfer rates up to 920Kbps and ECP/EPP
parallel port(s) which supports data transfer rates up to 2MB/sec.
Since this installation guide is written for all Cyber PCI I/O boards,
some features on this installation guide might not be present on the
model you bought. Please only refer to the features that apply to
your board.
Features and Benefits
• Conforms to PCI v2.1 Plug and Play
• Full support for DOS- and Windows-based software
• Improves I/O access speed up to 8 times faster than existing
ISA-bus serial ports. Reduces CPU load and improves system
performance dramatically
• IRQ sharing feature eliminates IRQ conflicts
Serial interface:
• High-speed 16550/16650/16850 UART serial port (9-pin)
supports baud rates up to 920Kbps. Works with 56K V.90
external modems, ISDN terminal adapters, PDAs, digital
cameras, label printers and other serial port devices
• Built-in 16/32/128-byte FIFO buffers dramatically increase
data transmit/receive speed, especially under Windows
multitasking environment
Parallel interface:
• Conforms to IEEE 1284-1994 parallel port standard
• High-speed parallel port supports various types of parallel
port devices including removable cartridge drives, CD-R/
RWs, printers, SuperDiskTM LS-120 drives, scanners and more
• Supports EPP, ECP(PIO mode), Bi-directional Parallel Port
(BPP) and Standard Parallel Port (SPP) modes
2
System Requirements
• Pentium or equivalent computer with an available 32-bit PCI
slot
• DOS/Windows 3.1x, Windows 95/98/98 SE/ME/NT 4.0/
2000/XP
Package Contents
• One Cyber PCI I/O board
• One floppy driver diskette
• One 5-year warranty card
• This quick installation guide
Hardware Installation
General instructions for installing the card are provided below, since
the design of computer cases and motherboards vary. Refer to your
computer’s reference manual for further information, if needed.
Caution: Static Electricity Discharge may permanently damage your
system. To avoid possible static electricity discharge during the
installation, please follow the guidelines below:
• Discharge any static electricity build up in your body by touching
a large grounded metal surface or the computer’s case (if plugged
in), for a few seconds.
• During the installation, avoid any contact with internal parts.
Handle cards only by their external edges.
1. Turn OFF the power to your computer and any other connected
peripheral devices.
2. Unplug the power cord from the back of the computer.
3. Remove your computer’s cover.
4. Remove the slot bracket from an available PCI slot.
5. To install the card, carefully align the card's bus connector with
the selected PCI slot on the motherboard. Push the board down
firmly, but gently, until it is well seated.
6. Replace the slot bracket's holding screw to secure the card.
7. Replace the computer cover and reconnect the power cord.
3
Software Installation
This section provides information on how to install the
Cyber PCI I/O's drivers for the following operating systems:
Windows 95/98/98 SE/ME
Windows NT 4.0
Windows 2000/XP
DOS/Windows 3.1x
Windows 95 Driver Installation
1. At the Add New Hardware Wizard window, click Next.
2. Insert the Driver Installation diskette in the floppy drive, and
click Other Locations. Type in a:\Win95, click OK, then
Finish.
3. From the Insert Disk window, click OK. When the Copying
Files dialog box appears, type in a:\Win95, then click OK.
4. Remove the diskette and select Yes to restart your system.
Windows 98/98 SE Driver Installation
1. At the Add New Hardware Wizard window, click Next.
2. Select Search for the best driver for your devices
(Recommend), then click Next.
3. Select Specify a location, insert the Driver Installation diskette
and type in a:\Win98, then click Next.
4. Click Next, then Finish.
5. Remove the diskette and click Yes to restart your system.
Windows ME Driver Installation
1. At the Add New Hardware Wizard screen, choose Specify
the location of the driver (Advanced), then click Next.
2. Check Specify a location, insert the Driver Installation
diskette into your floppy drive, type in A:\Win98, then click
Next.
3. Click Next, and Finish to complete driver installation.
4. Remove the driver diskette and click Yes to restart Windows.
4
To verify successful installation in Windows 95/98/98 SE/ME:
1. From the main desktop, double click My Computer, Control
Panel, System, then click Device Manager.
2. Double click Ports (COM & LPT) and new Cyber PCI ports
should be displayed. Also, double click SIIG Cyber PCI
option and SIIG ... PCI Board should be displayed.
The board is ready to connect new devices.
Windows NT 4.0 Driver Installation
1. From the desktop click Start, then Run.
2. Insert the Driver Installation diskette, type in A:\NT4\setup,
then click OK.
3. Click Next when the Welcome window appears.
4. From Choose Destination Location window, click Next.
5. Remove the Driver Installation diskette, select Yes to restart
Windows and click Finish.
To verify successful installation in Windows NT 4.0:
1. Go to Start / Setting / Control Panel, double click SIIG Cyber
PCI 20X device icon.
2. New COM port address and LPT number will be assigned for
the ports when successfully installed. The board is ready to
connect devices.
Note If you plan to connect a parallel device other than a
printer to the parallel port, such as zip drive, or scanner,
please follow the next section to change the port's I/O
address to support these devices.
To change the I/O address in Windows NT 4.0:
1. Double click Start, Settings, Control Panel, then SIIG Cyber
PCI 20X device icon.
2. Highlight the LPT or COM address and click Settings.
3. Select or type in an I/O address supported by the device you
would like to configure and click OK. Make sure the selected
I/O address does not conflict with other device in your
system.
4. Select Restart Now for the new setup to take effect.
5
Windows 2000 Driver Installation
Windows 2000 will automatically detect and install the correct
driver for the CyberSerial PCI and CyberParallel PCI boards.
For the rest of the Cyber PCI I/O boards, please follow the
instructions below:
1. At the New Hardware Wizard, click Next.
2. Select Search for a suitable driver for my device
(recommended) and click Next.
3. Select Specify a location, uncheck the other options and click
Next.
4. Insert the Driver Installation diskette, type in A:\Win2K and
click OK.
5. Click Next and Finish to complete driver installation.
To verify successful installation in Windows 2000:
1. Double click My Computer, Control Panel, System,
Hardware, and click Device Manager.
2. Click on the + (plus sign) in front of Ports (Com & LPT).
3. New Cyber port(s) should be listed.
Windows XP Driver Installation
Windows XP will automatically detect and install the correct
driver for the CyberSerial PCI and CyberParallel PCI boards.
For the rest of the Cyber PCI I/O boards, please follow the
instructions below:
1. At the Found New Hardware Wizard, choose Install from a
list or specific location (Advanced), and click Next.
2. Insert the Driver Installation diskette, check Include this
location in the search: and uncheck the other check box.
3. Type in A:\win2k and click Next.
4. At the next Window, Hardware Installation, click Continue
Anyway, then Finish.
5. Repeat steps 1-4 X* more times to complete driver installation.
* X = the number of ports on the board
6
To verify successful installation in Windows XP:
1. Right click My Computer, click Manage, then select Device
Manager.
2. Click on the + (plus sign) in front of Ports (Com & LPT).
3. New Cyber port(s) should be listed.
DOS/Windows 3.1x Driver Installation
1. Insert the Driver Installation diskette, from the C: prompt,
type in copy a:\dos\*.*, then press <Enter>.
2. Type in edit autoexec.bat, then press <Enter>.
3. Add C:\CB20XPC.exe at the bottom of the autoexec.bat file.
4. Go to File, save the changes and exit.
5. Remove the diskette and restart the system for the new setup
to take effect.
Troubleshooting
Problem: I am installing a parallel port(s) and my system freezes up
when Windows tries to install the driver for my printer port.
Solution: Enter your system bios, set the onboard parallel port I/O
address to 278h, save and exit. In certain systems, the address 278h
is reserved for ISA boards. So when the PCI parallel port tries to
capture this address, your system gets confused and freezes up.
7
Technical Support
QUESTIONS? SIIG’s Online Support has the answers! Simply
visit our web site at www.siig.com and click on SUPPORT. Our
online support database is updated daily with new drivers and
solutions. The answers to your problems could be just a few clicks
away.
Return Merchandise Authorization (RMA)
SIIG warrants to the original buyer of the product that the hardware
is free of defects in materials and workmanship for a period of one,
two or five years from the date of purchase. If your product fails to
be in good working order during the warranty period, you may
return it to SIIG for repair or replacement at SIIG's option.
To return the product, you need to follow these steps.
Step 1: Contact SIIG's RMA Department
To obtain an RMA number, SIIG's RMA Department can be reached
by phone at (510)413-5333 or fax at (510)657-5962 or email at
service@siig.com. In order to issue an RMA number, the product
serial number is required. This number can be found on the side of
the box and on the back of the product.
Step 2: Complete the RMA form
• Fill out your Return Merchandise Authorization (RMA) form, and
include it in the package with the product.
• Properly pack the product for shipping. All software, cable(s) and
other accessories that came with the original package must be
included.
• Clearly write your RMA number on the top of the returned package
and on the accompanying RMA form.
SIIG will refuse to accept any shipping package, and will not
be responsible for a product returned without an RMA number
posted on the outside of the shipping carton.
Step 3: Ship the Product
You are responsible for the cost of shipping back to SIIG at the
following address:
SIIG, Inc. RMA#_______________
6078 Stewart Ave.
Fremont, CA 94538
SIIG will ship the repaired or replaced product via UPS Ground or
US Mail at no cost to you.
PRODUCT NAME MODEL NUMBER
Cyber PCI I/O IO18xx
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B
OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCC COMPLIANCE STATEMENT:
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC NOTICE:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio and
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
• Consult the dealer or an experienced radio or TV technician for help
Caution:
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
this equipment
THE PARTY RESPONSIBLE FOR
PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Ave.
Fremont, CA 94538-3152
SIIG and SIIG logo are registered trademarks of SIIG, Inc. Microsoft, Windows and Windows
NT are registered trademarks of Microsoft Corporation. Pentium is a registered trademark of
Intel Corporation. Other names used in publication are for identification only and may be
trademarks of their respective companies.
February, 2002 Copyright ©2002 by SIIG, Inc. All rights reserved.
Loading...