Page 1
HDMI 2.0 4K HDR 1x4 Splitter
HDBaseT Extender
with Auto-scaling
User Manual
04-1192A P/N: CE-H24N11-S1
Page 2
2
Safety and Notice
The device has been tested for conformance to safety regulations and
requirements, and has been certified for international use. However,
like all electronic equipment, the device should be used with care.
Please read and follow the safety instructions to protect yourself from
possible injury and to minimize the risk of damage to the unit.
• Follow all instructions and warnings marked on this unit.
• Do not attempt to service this unit yourself, except where
explained in this manual.
• Provide proper ventilation and air circulation and do not use near water.
• Keep objects that might damage the device and assure that the
placement of this unit is on a stable surface.
• Use only the power adapter and power cords and connection
cables designed for this unit.
• Do not use liquid or aerosol cleaners to clean this unit.
• Always unplug the power to the device before cleaning.
Package contents
• HDMI 2.0 4K HDR 1x4 Splitter HDBaseT Extender
• Receiver x3
• Power adapter DC 12V / 7.5A
• IR blaster x1 / IR Receiver x3
• Terminal block x4
• Mounting kit
• User Manual
Page 3
3
Features
• HDMI 2.0a compliant
• Supports 4K2K@60 4:4:4 8bits
• Supports HDR which is 4K2K@60 4:2:0 10bits
• Extends HDMI signal up to 198ft from the HDMI source at Full HD
1080p 36-bit, 114ft at 4K2K@60 444 (4K-HDR Technology)
• Supports PoC(Power over Cable)
• Supports two HDMI loopout
• HDCP bypass
• Supports EDID management
• Supports resolution downscaling from 4K2K to 1080P
• Bi-directional IR pass-though
• Pure unaltered uncompressed 7.1ch digital HDMI over Cat.5/5e/6
• Supports 7.1 channel digital audio
• Supports full frequency IR signal from 30KHz to 56KHz
• RS-232 Pass-Thru: Up to 115,200bps
Thank You
for your purchase!
1.
NOT supports
(1) Resolution downscaling from 4K2K@60 4:2:2 to 1080P
(2) Frame rate conversion
(3) 4K2K@60 4:2:2 to 4K2K@60 4:2:0
2. Splitter can bypass 4K HDR data content, but can NOT process it and make
HDR content 100% t into 1080p
3. The length depends on the characteristics and quality of the cables. Higher
resolutions and longer transmission distances require low skew cables
(<25ns/100m) for best performance. Unshielded CAT6 with metal RJ45 connectors
is recommended.
Page 4
4
Layout
1. Power LED:
2. Micro-USB: For technical support only [rmware update]
3. HDMI Signal LED: Input signal LED indicator (From the left side
to the right is Loopout #1signal LED indicator and Loopout #2
signal LED indicator)
4. Link Receiver LED: Link LED indicator 1- 4
5. HDMI Signal LED: Output signal LED indicator 1- 4
Rear Panel
6. Power jack: Connect to the DC 12V/7.5A power supply unit
7. EDID Management Rotary control:
8. RS-232(terminal block format): The order of RS-232 pin are TX,
RX, GND (from the left side to the right)
9. IR Blaster: Plugging in the extension cable of IR blaster
10. IR Receiver: Plugging in the extension cable of IR receiver
11. HDMI IN: Connect to a HDMI input source
12. HDMI LOOPOUT #1: Connect to a HDMI display
13. HDMI LOOPOUT #2: Connect to a HDMI display
14. HDMI Signal OUT1-4: Link to each HDMI display via a Cat-5/5e/6
cable with a HDMI over Cat.X receiver.
15. RJ-45: Ethernet
TX Front Panel
Page 5
5
RX Panel
1. Micro-USB: For technical support only [rmware update]
2. HDMI Signal LED: Output #1 signal LED indicator
3. HDMI Signal LED: Output #2 signal LED indicator
4. Power LED:
5. Link LED:
6. Signal LED: When receive the HDMI signal, LED light will shine
7. RJ45: Plug in a Cat5e/6 cable that needs to be linked to the TX
8. IR Receiver: Plugging in the extension cable of IR receiver
9. IR Blaster: Plugging in the extension cable of IR blaster
10. RS-232(terminal block format): The order of RS-232 pin are
TX, RX, GND (from the left side to the right)
11. Dip Switch: [ON] F/W update Mode; [OFF] Normal Mode
12. HDMI OUT #1: Connects to a HDMI display
13. HDMI OUT #2: Connects to a HDMI display
NOTICE:
While connecting a new monitor to the splitter, experiencing a short period
of time without display might be expected. The splitter will do Automatic
EDID learning which analyzes the newly connected monitor to see if the
EDID for the HDMI input is necessary to update!
Page 6
6
Application
MODE 0 Ultra HD(4K2K@60) – 8/10/12bit 3D HDR video & 7.1ch audio
MODE 1 Ultra HD(4K2K@60) – 8/10/12bit 3D HDR video & 2ch audio
MODE 2 Ultra HD(4K2K@30)(4K2K@60 420) – 8/10/12bit 3D HDR video & 7.1ch audio
MODE 3 Ultra HD(4K2K@30)(4K2K@60 420) – 8/10/12bit 3D HDR video & 2ch audio
MODE 4 Full-HD(1080p@60) – 12bit 3D video & 7.1ch audio
MODE 5 Full HD(1080p@60) – 8bit 2D video & 2ch audio
MODE 6 Learning EDID from loopout #1
MODE 7 Auto EDID analysis learning mode*
EDID Switch / Dip Switch
Position Description
PIN#1
OFF[]
Reserved
ON[]
Reserved
PIN#2
PIN#3
OFF[] OFF[]
Normal use
OFF[] ON[]
Reserved
ON[] OFF[]
For system rmware update
ON[] ON[]
For HDBaseT rmware update
Page 7
7
Firmware update
Main Board
1. Power on the device
2. Connect the Micro-USB cable between PC and device
3. Open rmware update software
4. Set the correct COM port and “DO NOT” click OPEN button
5. Click the Open Dialog button to open the Update window
6. Click the File button to select the main board rmware le
7. Click the Start button and the rmware will start to update
8. After updating, please power cycle the device
Page 8
8
Feb, 2019 Copyright © 2019 by SIIG, Inc. All rights reserved.
Support
For more info or tech support
http://www.siig.com/support
Input
1. Power on the device
2. Connect the Micro-USB cable between PC and device
3. Open rmware update software
4. Set the correct COM port and click OPEN button to connect software
5. Click the Open Dialog button to open the software folder
6. Save the rmware le in this software folder and reconnect the
Micro-USB cable
7. Open rmware update software and then device will start to
update rmware automatically
8. After update process is done, software will show “Success”
message and then be closed automatically
9. After updating, please power cycle the device
Output
1. Power on the device
2. Connect the Micro-USB cable between PC and device
3. Open rmware update software
4. Set the correct COM port and click OPEN button to connect software
5. Click the Open Dialog button to open the FW Update window
6. Click the File button to select the output rmware le
7. Click the Start button and the rmware will start to update
8. After updating, please power cycle the device
Loading...