Page 1
1
4K HDR HDMI 2.0 & USB 2.0
Extender Over HDBaseT
with RS-232 & IR
User Reference Guide
04-1123A
P/N: CE-H23411-S1
Page 2
2
Introduction
The 4K HDR HDMI 2.0 & USB 2.0 Extender Over HDBaseT
with RS-232 & IR extends HDMI transmission distance
up to 330ft (100m) at 1080p or 230ft (70m) at 4K over
an economical CAT5e/6 cable. Plus, bi-directional
extension of IR, RS232 and USB 2.0 for advanced and
interactive applications.
Features and Benefits
Supports video resolutions up to 4Kx2K @60Hz
(4:4:4 8bit) or HDR 4Kx2K @60Hz (4:2:0 10bit) to
deliver crystal clear images
7.1 Digital sound capabilities as well as
uncompressed LPCM and compressed DTS-HD
& Dolby True HD for a state-of-the-art
entertainment experience
PoC (Power over Cable) feature, only one power
adapter is required to power both the transmitter
and receiver units
Bi-directional IR sensors allow you to remotely
control the HDMI source device from the remote
display side or control the remote display from
the source device side
Supports 3D, CEC, HDMI 2.0 and HDCP 2.2
protocols. Bandwidth up to 18Gb/s
ARC feature allows you to free the audio from on-
demand content within a Smart TV with ARC
Premium metal housing with ventilation panels
improve heat dissipation for enhanced safety
and stability
Built-in phoenix connector for RS232 control
signal transmission or firmware update. Included
mounting ears for easy installation
Page 3
3
Specifications
Package Contents
4K HDR HDMI 2.0 & USB 2.0 Extender (TX & RX)
Power adapter
IR blaster extension cable & IR receiver extension
cable
Mounting ears & Screw kit
Terminal block
User Reference Guide
Compliance HDMI 2.0a / HDCP 2.2
Resolution HDR 4Kx2K @60Hz (4:2:0 10bit) / 4Kx2K@60Hz (4:4:4 8bit)
Audio LPCM, DTS-HD and Dolby True HD (7.1CH)
Transmission Distance
HDR 4Kx2K @60Hz: Up to 70m
1080p @60Hz: Up to 100m
IR Signal Frequency 20KHz to 60KHz
Connectors
TX:
1x 19-pin HDMI Type-A, Female
1x 3.5mm audio jack (Stereo)
1x 3.5mm IR Blaster
1x 3.5mm IR Receiver
1x 9-pin USB Type-A, Female (Device)
1x Micro USB, Female (Host)
1x Dip switch
1x 3-pin phoenix connector (RS-232)
3x LED indicator (Power/Link/Signal)
1x 8-pin RJ45
1x Power jack
RX:
1x 19-pin HDMI Type-A, Female
1x 3.5mm audio jack (Stereo)
1x S/PDIF output
1x 3.5mm IR Blaster
1x 3.5mm IR Receiver
1x 9-pin USB Type-A, Female (Device)
1x Micro USB, Female (Host)
1x Dip switch
1x 3-pin phoenix connector (RS-232)
3x LED indicator (Power/Link/Signal)
1x 8-pin RJ45
1x Power jack
Housing Material Metal
Power Adapter
Input: AC 100-240V/ 50~60Hz
Output: DC 24V / 1A
Page 4
4
IR Out
Note: With PoC technology, only one power
adapter is needed to power both the
Transmitter and Receiver.
Figure 1: Transmitter (TX) - front
Layout
HDMI In
Stereo Input
IR In
HDMI In: Connect your HDMI source here with
an HDMI cable (cable not included)
Stereo Input: Provides a channel to extend an
external analog audio to receiver over HDBaseT
IR Out: Infrared 3.5mm socket. Plug IR Blaster
extension cable here. See instructions on page 8.
IR In: Infrared 3.5mm socket. Plug IR Receiver
extension cable here. See instructions on page 8.
USB Type-A
Micro USB
RS-232
RJ45
Dip Switch
Power Jack
Figure 2: Transmitter (TX) - rear
Page 5
5
Figure 3: Receiver (RX) - front
USB Type-A: Connect to USB Device
Micro USB: Connect to USB Host
Phoenix connector (RS232): Connect to the
included terminal block and RS-232 connector
(not included), then connect to a serial port device
or computer for data transferring
Dip Switch: Refer to below table for configuration
- ON: In lower position
- OFF: In upper position
RJ45 (HDBT Out): Connect the Cat5e/6 cable
Power Jack: Connect the included 24V DC power
adapter here (or the Receiver's power jack)
HDMI Out
Stereo
Output
IR In
S/PDIF
Output
IR Out
DIP Switch Position Description
Pin 1 (opt io n 1)
TX On (default)
Connect Micro USB port to
USB Host
RX OFF (default)
Conn ect U SB de vi ce to
Typ e-A port
Pin 1 (opt io n 2)
TX OFF
Conn ect U SB de vi ce to
Typ e-A port
RX ON
Connect Micro USB port to
USB Host
Pin 2 & 3
Pin 2 (TX & RX) Pin 3 (TX & RX)
ON ON HDBa seT firmwa re upd ate
ON OFF HDB a s eT monitor mode
OFF ON System firmw are up da te
OFF (default) OFF (default) HDMI extender mode
Page 6
6
HDMI Out: Connect your HDMI display with an
HDMI cable (cable not included)
Stereo Output: External analog audio output
from transmitter over HDBaseT
S/PDIF Output: Local ARC output
IR Out: Infrared 3.5mm socket. Plug IR Blaster
extension cable here. See instructions on page 8.
IR In: Infrared 3.5mm socket. Plug IR Receiver
extension cable here. See instructions on page 8.
USB Type-A
Micro USB
RS-232
RJ45
Dip Switch
Power Jack
USB Type-A: Connect to USB Device
Micro USB: Connect to USB Host
Phoenix connector (RS232): Connect to the
included terminal block and RS-232 connector
(not included), then connect to a serial port device
or computer for data transferring
Dip Switch: Refer to the table on page 5 for
details.
RJ45 (HDBT In): Connect the Cat5e/6 cable
Power Jack: Connect the included 24V DC power
adapter here (or the Transmitter's power jack)
Figure 4: Receiver (RX) - rear
Page 7
7
RS-232 Wire Connection
1. Insert the included terminal block to Phoenix
connector.
2. Connect the wires (not included) to the included
Terminal Block and the RS232 connector as below
diagram.
- Via pin to pin (Parallel) connector or cable:
Figure 5
TX
RX
GND
3 TXD
5 GND
2 RXD
Figure 6
TX
RX
GND
3 TXD
5 GND
2 RXD
- Via null connector or cable:
Page 8
8
IR Extenders (20~60kHz IR devices supported)
IR Blaster cable: Plug into the Transmitter's or
Receiver's IR Out to emit IR signals
IR Receiver cable: Plug into the Receiver's or
Transmitter's IR In to receive IR signals
Control your media player (such as DVD) at the TV
side using the media player's remote controller
Plug the IR Receiver cable to the Receiver's IR In
port
Plug the IR Blaster cable to the Transmitter's IR
Out port.
Control your TV at the media player side using the
TV's remote controller
Plug the IR Receiver cable to the Transmitter's
IR In port.
Plug the IR Blaster cable to the Receiver's IR Out
port.
Figure 7: IR Blaster cable
(Connect to IR Out)
Figure 8: IR Receiver cable
(Connect to IR In)
Important Note: Incorrect placement of IR Receiver
and IR Blaster cables may result in cable failures.
Please check carefully before plugging in the IR cables
to proper IR sockets.
Page 9
9
Hardware Installation
Note: To achieve optimal performance, a shielded 100%
copper wire CAT6/7 cable is recommended.
1. Power off all devices including your HDMI source
and display.
2. Connect your HDMI source to the Transmitter's
HDMI IN connector with an HDMI cable (not
included).
3. Optional: Connect the IR Receiver or Blaster
extension cable according to the instructions on
page 8.
4. Connect USB Host/Device to both TX and RX
units.
5. Connect audio source to TX and audio receiver/
speaker to RX unit.
6. Connect your HDMI display to the Receiver's
HDMI OUT connector with a HDMI cable (not
included).
7. Optional: Connect the IR Receiver or Blaster
extension cable according to the instructions on
page 8.
8. Connect and link the Transmitter and Receiver
by a CAT5e/6 cable.
9. Plug the included power adapter into the
Transmitter's or Receiver's Power Jack, then
plug the power adapter into a reliable power
outlet. (Note: It's recommended to connect it to
the Transmitter)
10. Power on your HDMI device and HDMI display.
11. The HDMI Extender is ready for use.
Page 10
10
Application
Extends HDMI signals such as game consoles, DVD
players or computers up to 100m (330ft). Equipped
with bi-directional IR pass-through path, RS-232 serial
port control and USB 2.0, offers the convenient path
for interactive applications, such as touch panels.
Makes it a great solution for digital signage with long
distance A/V transmission.
Figure 9: Application
* When using the remote control, please make sure its distance to the IR
Receiver extension cable is within 5m (16.4ft) and without obstructions.
Blu-ray player
HDMI display
Control system
Stereo input
Page 11
11
Technical Support and Warranty
QUESTIONS? SIIG’s Online Support has answers! Simply visit our web site
at www.siig.com and click Support. Our online support database is updated
daily with new drivers and solutions. Answers to your questions could be just
a few clicks away. You can also submit questions online and a technical support
analyst will promptly respond.
SIIG offers a 3-year manufacturer warranty with this product. This warranty
covers the original purchaser and guarantees the product to be free of any defects
in materials or workmanship for three (3) years from the date of purchase of the
product. This warranty is not transferable and is available only to the original
purchaser of the product.
SIIG will, at our discretion, repair or replace (with an identical product or product
having similar features and functionality) the product if defective in materials or
workmanship. This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state. Please see our web site for more
warranty details.
If you encounter any problems with this product, please follow the procedures
below.
A) If it is within the store's return policy period, please return the product to the
store where you purchased it.
B) If your purchase has passed the store's return policy period, please follow these
steps to have the product repaired or replaced.
Step 1: Submit your RMA request. Go to www.siig.com, click Support, then
Request A Product Replacement to submit a request to
SIIG RMA or fax
a request to 510-657-5962. Your RMA request will be processed, if the product
is determined to be defective, an RMA number will be issued.
Step 2: After obtaining an RMA number, ship the product.
• Properly pack the product for shipping. All software, cable(s) and any
other accessories that came with the original package must be included
• Include a copy of your original sales receipt inside the package with date
of purchase and place of purchase circled and clearly visible
• Clearly write your RMA number on the top of the returned package. SIIG
will refuse to accept any shipping package, and will not be responsible for
a product returned without an RMA number posted on the outside of the
shipping carton
• You are responsible for the cost of shipping to SIIG. Ship the product to
the following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA #:
• SIIG will ship the repaired or replaced product via Ground in the U.S. and
International Economy outside of the U.S. at no cost to the customer
Page 12
12
About SIIG, Inc.
Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity
solutions (including Serial ATA and Ultra ATA Controllers, FireWire, USB,
and legacy I/O adapters) that bridge the connection between Desktop/
Notebook systems and external peripherals. SIIG continues to grow by
adding A/V and Digital Signage connectivity solutions to our extensive
portfolio. All centered around the distribution and switching of A/V signals
over CAT5/6, these products include matrix switches, distribution amplifiers,
extenders, converters, splitters, cabling, and more.
SIIG is the premier one-stop source of upgrades and is committed to
providing high quality products while keeping economical and competitive
prices. High-quality control standards are evident by one of the lowest
defective return rates in the industry. Our products offer comprehensive
user manuals, user-friendly features, and are backed by an extensive
manufacturer warranty.
SIIG products can be found in many computer retail stores, mail order
catalogs, and e-commerce sites in the Americas, as well as through major
distributors, system integrators, VARs and e-commerce sites.
PRODUCT NAME
4K HDR HDMI 2.0 & USB 2.0 Extender Over HDBaseT
with RS-232 & IR
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCC COMPLIANCE STATEMENT:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
Phone: 510-657-8688
4K HDR HDMI 2.0 & USB 2.0 Extender Over HDBaseT with RS-232 & IR is a trademark of SIIG, Inc. SIIG
and the SIIG logo are registered trademarks of SIIG, Inc. All other names used in this publication are
for identification only and may be trademarks of their respective owners.
March, 2018 Copyright © 2018 by SIIG, Inc. All rights reserved.
Loading...