SIIG CE-DS0011-S1, CE-DS0111-S1 Quick Installation Manual
Full-HD Digital Signage
Player
Quick Installation Guide
Introduction
The CE-DS0011-S1/CE-DS0111-S1 is a Full-HD Digital Signage Player
featuring industrial grade mechanical design and versatile open-standard
SMIL programmability
Features and Benefits
Full-HD 1080p video decoding of MPEG, H.264, and VC-1 media
formats
4GB on-board flash local storage with CF card slot
Integrated audio and video output via HDMI
IEEE 802.3 Ethernet 10/100 Base-T with auto-MDIX
Supports full POPAI Screen Media Formats Standards Profiles S1 to S12,
and E1 to E9
Supports HTML5 technologies including CSS and JavaScript
SmartWidgets: clock, calendar, news, weather, RSS, Twitter, web content
Compliant with Wireless 802.11 b/g/n standards (
CE-DS0111-S1 Only)
Package Contents
Full-HD Digital Signage Player
Power Adapter
Ethernet Cable
Standard 3.5mm to RCA AV cable
Quick installation guide
Software CD
W i-Fi Antenna (
CE-DS0111-S1 Only)
04-0762B
1
Layout
A
V
V
(
)
HDMI
12V DC In
GA
Figure1:Full‐HDDigitalSignagePlayerlayout
ESA mount
Reset
V out
MIS-D-100
Ethernet
USB x 2
Wi-Fi antenna
CF card slot (covered)
Physical features (left to right in above illustration)
12V DC in: For power adapter
HDMI: Connector for digital video and audio combined outputs, or
digital video via option DVI adapter
VGA: For analog video output
AV out: 3.5mm composite AV output
Reset: S/W button to perform factory reset
Ethernet: For network content update
USB: USB content update and configuration
CF card slot cover: Integrated CF card removing tool
Mounting and Installation
The player can be attached to mounting posts
on the back of screens or inside cabinetry
with the built in VESA MIS-D100
(100mmx100mm) compatible mounting
flange
2
For CE-DS0111-S1 only
Connect the Wireless antenna as shown.
Screw antenna clockwise onto the post.
Configuring
1. Connect a video cable (either VGA or HDMI) to your monitor.
- When using the VGA connection, your monitor should support
XGA (1024x768) resolution or greater. For audio output, you will
also need to connect a stereo RCA cable from the Full-HD Digital
Signage player to your monitor.
- When using HDMI connection, audio and video are sent over a
single HDMI cable.
2. Plug the power adapter into the Full-HD Digital Sign age Player then
plug the power adapter into a reliable power source. Shortly afterwards,
the following progress bar will be displayed on your monitor:
~90 seconds
3. Player boot process takes approximately 90 seconds to complete. The
player will indicate that it is ready for content sync via the USB port or,
if content has been loaded, begin playback immediately.
4. Plug in a USB keyboard to the unit’s USB port the player will enter the
graphical menu system in approximate 30 sec.
5. Navigate the menus using your keyboard arrows keys, space bar, enter
key, and numeral keys on your USB keyboard. Use the keyboard
arrow keys to highlight menu items, press the space bar to move the
star (cursor), and then press enter to confirm(<OK>) or reject(<Cancel>)
any changes.
3
Connect the Full-HD Digital Signage Player to your network
Enter Network setting in the menu to set up a network connection method.
Wireless connection (CE-DS0111-S1 only)
The player will scan for wireless sign als nearby
during boot up. If the network requires
authentication, you will be asked to provide the
password for access.
Wired con nection
To use the wired Ethernet connection, connect an Ethernet cable and the
Wi-Fi (CE-DS0111-S1) will be disabled.
Player IP address
You will also need an IP address for the player on your network. This could
be set automatically (DHCP) or manually (static IP):
DHCP – automatically assign network IP address
DHCP is enabled by default. You do not need to change the settings unless
setting a static IP.
Static IP – manually assign network IP address
Highlight IP configuration and press Enter on keyboard to <Select>
Move the highlight to Static IP below, press Space bar on the keyboard to
fill in the star (*) at the Static IP brackets, and press Enter on the keyboard
to select <OK>.
Proceed to configure an available static IP address. Select Wireless
configuration or IP configuration as determined by your connection. Please
consult your network administrator for assistance if necessary.
4
Video Output Settings
For best quality, set the output resolution to match your display’s native
resolution to avoid image scaling and blur.
If you are connecting to an LCD TV, the resolution setting is most likely
1366x768, 1280x720, or 1920x1080. If you are connecting a LCD
computer monitor, projector, or plasma display, refer to the device
specifications for the best matching setting.
Press the space bar to fill in the star (*) before
pressing the enter key for <OK>.
Clock and calendar settings
Set the correct time zone, time, and date. Daylight Saving (DST) rules can
be configured in Set time zone.
Setting a password
To prevent unauthorized modification of player settings, set a player
password to hide the menu.
From the top level menu, select Change password to set a password.
IMPORTANT: Once a password is set, you
can only access the menus by connecting a USB
keyboard and pressing CTRL + ALT +
DELETE (3-key combination) simultaneously.
You may connect the keyboard at any stage of
player operation or before/ during boot-up.
If you forget the password, you will need to
reset the device. See Reset Player to Factory
Default.
5
Software Installation
1. Before the installation
Mini mu m S y st em Requ i rements :
• 1 GHz AMD or Intel CPU
• 512 MB RAM
• Windows XP, Windows Vista, or Windows 7
• DirectX 9
• Microsoft .NET framework 4.0
If your computer wasn’t equipped with .Net Framework 4.0, please
find .Net Framework 4.0 in the attached CD and install it.
Or you can download the latest version from the internet directly.
2. Start to run Signage Manager Express installer
(1) Find the Signage Manager Express installer icon in your software
CD and double click on it.
(2) Follow the pop out screen instructions to install Signage Manager
Express.
6
(3) After finish installation, double-click the Signage Manager Express
icon to launch the software.
For the first launch, the following window will appear.
Click OK to start it.
7
Software Operation
Signage Manager Express software provides an easy way to let users to export
various media files to the display. Follow the following steps to do the display
settings:
1. Select Player Model
Select a suitable player model. In general, we use Full HD Open API
Player V2 model.
Click Network Media Player -> Full HD Open API Pl ayer V2
2. Choose aspect ratio and display format
(1) Click Aspect ratio to choose a display ratio from the list.
8
Loading...