SIIG 1S1P PCI User Manual

Cyber 1S1P PCI
Quick Installation Guide

Introducing the Cyber 1S1P PCI

The Cyber 1S1P PCI high-speed serial I/O card provides
one 9-pin serial port and one parallel port.

Features and Benefits

• Conforms to PCI v2.2 Plug and Play

• Full support for Windows-based software

• Reduces CPU load and improves system

performance dramatically

• IRQ sharing feature reduces IRQ conflicts

• High-speed serial port (9-pin) works with 56K V.90

external modems, ISDN terminal adapters, PDAs,
digital cameras, label printers and other serial port
devices

• Built-in FIFO buffers dramatically increase data

transmit/receive speed, especially under Windows'
multitasking environment

• Each serial port can be configured for either 5v or

12v output, for serial devices that require power

• IEEE 1284 compliant SPP/EPP/ECP parallel port

System Requirements

• Pentium or equivalent computer with an available

PCI slot

• Windows 95/98/98SE/ME/NT 4.0/2000/XP/

Server 2003

04-0344A

1

Package Contents

• (1) Cyber 1S1P PCI board

• (1) Driver CD

• (1) Quick Installation Guide

Layout

JP1

Serial Port

Parallel Port

Figure 1. Layout

Jumper Settings (JP1)

Open = 0 volts (default)
Short 1-2 = 5v
Short 2-3 = 12v

Note: Most serial devices do not require additional
power through the serial port. Refer to your serial
device's manual for more information. This jumper
can be removed if it's not used.

2

Hardware Installation

General instructions for installing the card are provided
below, since the design of computer cases and
motherboards vary. Refer to your computer’s reference
manual for further information, if needed.

Static Electricity Discharge may permanently damage
your system. Discharge any static electricity build up in
your body by touching your computer’s case for a few
seconds. Avoid any contact with internal parts and
handle cards only by their external edges.

1. Turn OFF the power to your computer and any
other connected peripheral devices.

2. Unplug the power cord from the back of the
computer.

3. Remove your computer’s cover.

4. Remove the slot bracket from an available PCI slot.

5. Change JP1 jumper settings to the desired voltage
only if your serial device needs additional power
from the serial port. However, most serial devices
do not require additional power. For more
information, see Figure 1 on page 2. Skip this step
if power is not required.

6. To install the card, carefully align the card's bus
connector with the selected PCI slot on the
motherboard. Push the board down firmly, but
gently, until it is well seated.

7. Replace the slot bracket's holding screw to secure
the card.

8. Replace the computer cover and reconnect the power
cord.

3

Software Installation

This section provides information on how to install the
Cyber 1S1P PCI drivers.

Windows 95 Driver Installation

1. At the Update Device Driver Wizard window, click
Next.

2. Insert the driver CD, and click Other Locations.
Type in D:\9x, click OK, then Finish. (Change D: to
match your CD-ROM drive letter)

3. From the Insert Disk window, click OK. When the

Copying Files dialog box appears, type in
D:\9x, then click OK.

4. Repeat steps 1-3.

5. Restart Windows to complete the installation.

Windows 98/98SE Driver Installation

1. At the Add New Hardware Wizard window, click
Next.

2. Select Search for the best driver for your device
(Recommended), then click Next.

3. Select Specify a location, uncheck the other boxes,
insert the driver CD, type in D:\9x, then click Next.
(Change D: to match your CD-ROM drive letter)

4. Click Next, then Finish.

5. Repeat steps 1-4.

6. Restart Windows to complete the installation.

4