Page 1
1x2 HDMI Splitter with
4Kx2K & EDID Management
Installation Guide
Introduction
The 1x2 HDMI Splitter with 4Kx2K & EDID
Management splits one HDMI signal to two HDMI
displays at up to 4Kx2K resolution.
Key Features and Benefits
• Broadcast HDMI video/audio signals from
one HDMI source to two HDMI displays
without losing quality
• Supports HDMI Deep Color & 3D
• Supports 1080p and up to 4Kx2K PC
resolution
• Supports Dolby Digital, DTS-HD and Dolby
True-HD audio
• Video bandwidth: 340MHz (10.2Gbps)
• Embedded EDID and EDID learning ability
04-0945A
1
Page 2
Package Contents
• 1x2 HDMI Splitter with 4Kx2K & EDID
Management
• Power adapter (Output: 5V/2A)
• Mounting screws (2)
• Installation guide
Layout
DC 5V
MODE
HDMI
OUT 2
F/W
HDMI IN
Figure 1: Rear Panel
HDMI
OUT 1
• HDMI IN: Connects to your HDMI source
device by using an HDMI cable (cable not
included)
• HDMI OUT 1-2: Connects to your HDMI
displays by using HDMI cables (cables not
included)
• F/W: For future firmware update
2
Page 3
• MODE: Selects alternate EDID modes and
functions. See Mode Dial in page 4 & 5.
• DC 5V: Power adapter jack for the included
5V power adapter
POWER
LED
Figure 2: Front Panel
SIGNAL
LED
• POWER LED: On when the Splitter is
powered on
• SIGNAL LED: On when HDMI source is
detected
Hardware Installation
1. Power off all devices you plan to connect to
the Splitter.
2. Connect your HDMI source's HDMI output
to the Splitter's HDMI IN using an HDMI
cable (HDMI cable not included).
3
Page 4
3. Connect your HDMI displays to the Splitter's
HDMI OUT using HDMI cables (HDMI
cables not included).
4. Connect the included power adapter to the
Splitter's DC 5V power jack and plug it into
a reliable power outlet.
5. Power on all of the connected devices.
6. The Splitter is now ready to use.
NOTE: To achieve 3D and 2Kx4K output,
make sure this standard is supported by
your display(s), and High Speed HDMI
cables with Ethernet are used.
Mode Dial
EDID is used to transmit the make, model and
characteristics of a monitor to the display adapter
of the computer. It is also used by an HDTV to
identify it's maximum resolution to the DVD
player, A/V receiver or video processor. Use a
flat head screwdriver to rotate the Mode Dial to
select amongst the options.
4
Page 5
0: Firmware update
1: EDID Full-HD (1080p@60) - 24bit 2D video
& 7.1ch audio
2: EDID Full-HD (1080p@60) - 24bit 2D video
& 2ch audio
3: EDID Full-HD (4K2K@30) - 24bit 2D video
& 7.1ch audio
4: EDID Full-HD (4K2K@30) - 24bit 2D video
5: EDID HD (1080p@30)(1080i@60)(720p@
60) - 24bit 2D video & 2ch audio
6: Auto EDID mode: Automatically detect
and analyze the EDID of all the connected
HDMI displays. The HDMI source player
will defer to the lowest resolution HDMI
display
7: EDID Learning mode: Learns the EDID of
the HDMI display connected to HDMI OUT
1 of the Splitter
5
Page 6
Application
HDMI source
* Input length: 5m (Max)
* Output length: 10m (Max)
3DTV
3DTV
Figure 3: Application
6
Page 7
Technical Support and Warranty
QUESTIONS? SIIG’s Online Support has answers! Simply visit our web site at
www.siig.com and click Support. Our online support database is updated daily with
new drivers and solutions. Answers to your questions could be just a few clicks away.
You can also submit questions online and a technical support analyst will promptly
respond.
SIIG offers a 2-year manufacturer warranty with this product. This warranty covers the
original purchaser and guarantees the product to be free of any defects in materials or
workmanship for two (2) years from the date of purchase of the product.
SIIG will, at our discretion, repair or replace (with an identical product or product
having similar features and functionality) the product if defective in materials or
workmanship. This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state. Please see our web site for more warranty details.
If you encounter any problems with this product, please follow the procedures below.
A) If it is within the store's return policy period, please return the product to the store
where you purchased from.
B) If your purchase has passed the store's return policy period, please follow the steps
below to have the product repaired or replaced.
Step 1: Submit your RMA request.
Go to www.siig.com, click Support, then REQUEST A PRODUCT REPLACEMENT
to submit a request to SIIG RMA or fax a request to 510-657-5962. Your RMA request
will be processed, if the product is determined to be defective, an RMA number will
be issued.
Step 2: After obtaining an RMA number, ship the product.
• Properly pack the product for shipping. All accessories that came with the
original package must be included.
• Clearly write your RMA number on the top of the returned package. SIIG will
refuse to accept any shipping package, and will not be responsible for a product
returned without an RMA number posted on the outside of the shipping
carton.
• You are responsible for the cost of shipping to SIIG. Ship the product to the
following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA #:
• SIIG will ship the repaired or replaced product via Ground in the U.S. and
International Economy outside of the U.S. at no cost to the customer.
7
Page 8
About SIIG, Inc.
Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity
solutions (including Serial ATA and Ultra ATA Controllers, FireWire, USB,
and legacy I/O adapters) that bridge the connection between Desktop/
Notebook systems and external peripherals. SIIG continues to grow by adding
A/V and Digital Signage connectivity solutions to our extensive portfolio.
SIIG products offer comprehensive user manuals, many user-friendly features,
and are backed by an extensive manufacturer warranty. High quality control
standards are evident by the overall ease of installation and compatibility of
our products, as well as one of the lowest defective return rates in the industry.
SIIG products can be found in computer retail stores, mail order catalogs,
through major distributors, system integrators, and VARs in the Americas and
the UK, and through e-commerce sites.
1 x 2 HDMI Splitter with 4Kx2K & EDID Management
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B
OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
Phone: 510-657-8688
1x2 HDMI Splitter with 4Kx2K & EDID Management is a trademark of SIIG, Inc. SIIG and
the SIIG logo are registered trademarks of SIIG, Inc. All other names used in this publication
are for identification only and may be trademarks of their respective owners.
March, 2014 Copyright © 2014 by SIIG, Inc. All rights reserved.
PRODUCT NAME
FCC COMPLIANCE STATEMENT:
Loading...