Articulating Monitor Desk
Mount - 13" to 27"
Installation Instructions
04-0680B
1
Unpacking
• Carefully remove contents and lay out on
cardboard or other protective surface
• Check package contents against the parts
list to ensure that all components were
received undamaged. Do not use damaged
or defective parts
• Carefully read all instructions before
attempting installation
Safety Information
• Use proper safety equipment during
installation
• If you don't understand the installation
instructions, please consult an installation
specialist
• Do not use this product for any purpose or
in any configuration not explicitly specified
in these instructions
2
Parts List
a - (1x) 35mm
Tube Support
d - (4x) M4x12 Bolt e - (4x) M4x30 Bolt
h - (2x) Wire Clip
i - (2x) M10x15 Bolt
b - (1x) C Clamp
f - (8x) M4 Washer
j - (1x) Allen Key k - (2x) Spare
c - (1x) Vesa
Plate with Arm
(4x) M4 Spacer
Plastic Cover
Tools Required
• Phillips screwdriver
Installation
Caution: This monitor desk mount must be securly
attached to the horizontal desktop. If the mount
is not properly installed it may fall, resulting in
possible injury and/or damage.
3
1. Install the C Clamp (b) to the 35mm Tube
Support (a) according to the thickness of
the desktop. The thickness can be changed
in three positions. Connect it using 2
M10x15 Bolts (i) and tighten using the Allen
Key (j). Tighten the C Clamp to the desktop
using the 2 eye bolts.
4
2. Install the Vesa Plate with Arm (c) to the
tube support, make sure the wire clips are
on the bottom. Tighten the clamp bolt using
the Allen Key (j).
Caution: When installing the VESA Plate
with Arm (c), DO NOT over tighten the
clamp bolt. The VESA Plate with Arm is
intended to rotate (360 degrees) and is not
meant to be attached in a fixed position.
Tighten the bolt only tight enough to keep
the VESA Plate with Arm at the desired
height position. Over tightening the bolt
may result in damage to the clamp.
5
3. Mount the monitor to the Vesa plate.
3-1. For flat back monitors use M4x12 Bolt
(d) and M4 Washer (f).
Flat Back Monitor
6
3-2. For curved back monitors use M4
Spacer (g), M4x30 Bolt (e) and M4 Washer
(f).
Curved Back Monitor
7
4. Adjust the height and install the Wire Clips
(h).
Adjust Height
Install Wire Clips
8
5. Check the tightness, arrange the cables
through the wire clips, and make any final
adjustments.
Check Tightness
Arrange Cables
9
Blank Page
10
Technical Support and Warranty
QUESTIONS? SIIG’s Online Support has answers! Simply visit our web site at
www.siig.com and click Support. Our online support database is updated daily with
new drivers and solutions. Answers to your questions could be just a few clicks away. You
can also submit questions online and a technical support analyst will promptly respond.
SIIG offers a 5-year manufacturer warranty with this product. This warranty covers the
original purchaser and guarantees the product to be free of any defects in materials or
workmanship for five (5) years from the date of purchase of the product.
SIIG will, at our discretion, repair or replace (with an identical product or product having
similar features and functionality) the product if defective in materials or workmanship.
This warranty gives you specific legal rights, and you may also have other rights which
vary from state to state. Please see our web site for more warranty details.
If you encounter any problems with this product, please follow the procedures below.
A) If it is within the store's return policy period, please return the product to the store
where you purchased from.
B) If your purchase has passed the store's return policy period, please follow the steps
below to have the product repaired or replaced.
Step 1: Submit your RMA request.
Go to www.siig.com, click Support, then RMA to submit a request to SIIG RMA or
fax a request to 510-657-5962. Your RMA request will be processed, if the product
is determined to be defective, an RMA number will be issued.
Step 2: After obtaining an RMA number, ship the product.
• Properly pack the product for shipping. All accessories that came with the
original package must be included.
• Clearly write your RMA number on the top of the returned package. SIIG will
refuse to accept any shipping package, and will not be responsible for a product
returned without an RMA number posted on the outside of the shipping
carton.
• You are responsible for the cost of shipping to SIIG. Ship the product to the
following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA #:
• SIIG will ship the repaired or replaced product via Ground in the U.S. and
International Economy outside of the U.S. at no cost to the customer.
11
About SIIG, Inc.
Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity solutions
(including Serial ATA and Ultra ATA Controllers, FireWire, USB, and legacy I/
O adapters) that bridge the connection between Desktop/Notebook systems and
external peripherals. SIIG continues to grow by adding A/V and Digital
Signage connectivity solutions to our extensive portfolio.
SIIG products offer comprehensive user manuals, many user-friendly features,
and are backed by an extensive manufacturer warranty. High quality control
standards are evident by the overall ease of installation and compatibility of
our products, as well as one of the lowest defective return rates in the industry.
SIIG products can be found in computer retail stores, mail order catalogs,
through major distributors, system integrators, and VARs in the Americas and
the UK, and through e-commerce sites.
Articulating Monitor Desk Mount 13" to 27"
Articulating Monitor Desk Mount - 13" to 27" is a trademark of SIIG, Inc. SIIG and the SIIG
logo are registered trademarks of SIIG, Inc. All other names used in this publication are for
identification only and may be trademarks of their respective owners.
June, 2011 Copyright © 2011 by SIIG, Inc. All rights reserved.
PRODUCT NAME
Loading...