SIIG 04-0600B User Manual

Satellite Speaker
Mounts - 1 Pair

Quick Installation Guide

Introduction

The Satellite Speaker Mounts - 1 Pair are fully-adjustable (Tilt,
Swivel, & Pivot) speaker wall or ceiling mounts.

Key Features and Benefits

• Universal design fits most speaker brands & designs

• Ceiling or wall mountable & compatible with 1, 2, or
4-hole and key-hole speaker mounting (with included
adapters)

• Allows customizable tilt, swivel, & pivot angle
adjustments for optimal speaker positioning

• Holds speakers weighing up to 8 lbs

Serial Number Sticker

For future product return or exchange, this serial number is
required. Please keep it for your reference.

04-0600B

1

Package Contents

• (2) Speaker mounts

• (2) 1-hole adapters

• (2) 2/4-hole adapters

• (2) 2 ¼” ceiling mount extensions

• Mounting hardware

• Quick installation guide

Mounting Hardware

M6x20mm Machine Screw
M5 x 20mm Machine Screw

8-32 x 5/8" Machine Screw
1/4"-20 x 1/2" Machine Screw

M5 x 1/8" Plastic Screw

8-32 Hex Key Hole Nut

#8 x 3/4" Self Tapping Screw

#12 x 3/4" Self Tapping Screw

#12 x 1 3/4" Self Tapping Screw

#12-14 Alligator Anchor

M4 x 8mm Flat Head Machine Screw

2

Installation

Please read the instructions prior to installation. This speaker
mount is designed solely for the mounting of small speakers
weighing less than 8lbs. We are not responsible for damage
that may occur if speakers weighing more than 8lbs. are
used.

The user will have to determine which type of configuration
will work best with the included mounting hardware. If the
included hardware does not fit with the application, the
appropriate hardware will have to be purchased.

Single Hole Mounting

1. Most satellite speakers will require the use of the
M5 x 20mm machine screw used in combination with
M5 x 1/8" plastic washer. The plastic washer is used as
a spacer between the threaded insert and the post, see
Figure 1 below. It is critical the plastic washer is used
correctly.

M5 x 20mm

Machine Screw

Back Speaker

Mounting Post

M5 x 1/8"

Plastic Washer

Figure 1

3

2. Once the proper configuration is determined, secure
the post to the speaker.

3. Some speakers use the smaller M4 x 8 screw, which is
inserted into the off-center on the mounting post, see
Figure 2 below.

M4 x 8mm Flat Head

Machine Screw

Back Speaker

Figure 2

4. Check the size of the hole, make sure you have the
8-32 x 5/8" machine screw, the 1/4"-20 x 1/2" machine
screw, the M6 x 20mm, or the M5 x 20mm fits inside,
see Figure 3 below.

M5 x 1/8" Plastic Washer

Back Speaker

4

8-32 x 5/8" Machine Screw

1/4"-20 x 1/2" Machine Screw

Figure 3

5. When the correct size is determined, place the screw
through the speaker post and attach to the rear of the
speaker enclosure. If the screw does not tighten
properly, use the M5 x 1/8" plastic washer to tighten
it up.

Key Hole Mounting

1. If your speaker has a factory key hole design, you will
use the 8-32 x 5/8" machine screws in combination
with the 8-32 Hex Key Hole Nut.

2. Loosely pre-assemble the mounting post with the
8-32 x 5/8" machine screw and hex key hole nut, see
Figure 4 below.

Keyhole

Back Speaker

8-32 Hex Key Hole Nut

Mounting Post

Figure 4

M5 x 1/8"

Plastic Washer

8-32 x 5/8"

Machine Screw

5