SIIG 04-0600A User Manual

Satellite Speaker
Mounts - 1 Pair

Quick Installation Guide

Introducing the Satellite Speaker

The Satellite Speaker Mounts - 1 Pair are fully-adjustable
(Tilt, Swivel, & Pivot) speaker wall or ceiling mounts.

Key Features and Benefits

• Universal design fits most speaker brands & designs

• Ceiling or wall mountable & compatible with 1, 2,
or 4-hole and key-hole speaker mounting (with

included adapters)

• Allows customizable tilt, swivel, & pivot angle
adjustments for optimal speaker positioning

• Holds speakers weighing up to 8 lbs

Serial Number Sticker

For future product return or exchange, this serial number
is required. Please keep it for your reference.

04-0600A

1

Package Contents

• (2) Speaker mounts

• (2) 1-hole adapters

• (2) 2/4-hole adapters

• (2) 2 ¼” ceiling mount extensions

• Mounting hardware

• Quick installation guide

Mounting Hardware

M6x20mm Machine Screw
M5 x 20mm Machine Screw

8-32 x 5/8" Machine Screw
1/4"-20 x 1/2" Machine Screw

M5 x 1/8" Plastic Screw

8-32 Round Key hole Nut

#8 x 3/4" Self Tapping Screw
#12 x 3/4" Self Tapping Screw

#12 x 1-3/2" Self Tapping Screw
#12-14 Alligator Anchor

M4 x 8mm Flat Head Machine Screw

2

Installation

Please read the instructions prior to installation. This
speaker mount is designed solely for the mounting of
small speakers weighing less than 8lbs. We are not
responsible for damage that may occur if speakers
weighing more than 8lbs. are used.

The user will have to determine which type of configuration
will work best with the included mounting hardware. If
the included hardware does not fit with the application,
the appropriate hardware will have to be purchased.

Single Hole Mounting

1. Most satellite speakers will require the use of the
M5 x 20mm machine screw used in combination
with M5 x 1/8" plastic washer. The plastic washer
is used as a spacer between the threaded insert and
the post, see Figure 1 below. It is critical the plastic
washer is used correctly.

M5 x 20mm
Machine Screw

Back Speaker

Mounting Post

M5 x 1/8"
Plastic Washer

Figure 1

3

2. Once the proper configuration is determined, secure
the post to the speaker.

3. Some speakers use the smaller M4 x 8 screw, which
is inserted into the off-center on the mounting post,
see Figure 2 below.

M4 x 8mm Flat Head
Machine Screw

Back Speaker

Figure 2

4. Check the size of the hole, make sure you have the
5/8"-32 x 5/8" machine screw, the 1/4"-20 x 1/2"
machine screw, the M6 x 20mm, or the M5 x 20mm
fits inside, see Figure 3 below.

M5 x 1/8" Plastic Washer

Back Speaker

4

5/8"-32x5/8" Machine Screw

1/4"-20 x 1/2" Machine Screw

Figure 3

5. When the correct size is determined, place the
screw through the speaker post and attach to the
rear of the speaker enclosure. If the screw does not
tighten properly, use the M5 x 1/8" plastic washer
to tighten it up.

Key Hole Mounting

1. If your speaker has a factory key hole design, you
will use the 5/8"-32 x 5/8" machine screws in
combination with the key hole nut.

2. Loosely pre-assemble the mounting post with the
5/8"-32 x 5/8" machine screw and key hole nut, see
Figure 4 below. Be sure the key hole nut is installed
with the knurled (rough) edge toward the host.

Keyhole

Back Speaker

Mounting Post

Figure 4

M5 x 1/8"
Plastic Washer

5/8"-32x5/8"
Machine Screw

5/8"-32x5/8"
Machine Screw

5