SIIG 04-0528C User Manual
Low Profile Universal TV Mount - 32" to 60"
Installation Instructions
Fixed LCD / TFT TV Wall Mount
Material: 2.0mm Cold Rolled Steel Plate
TV Size: 32" - 60"
Max load capacity:165 lbs / 75 kgs
Wall distance: 30mm / 1.2"
Bubble level system included
Universal Mounting Pattern
IMPORTANT: If you don't understand the installation instructions, please consult an installation
specialist
04-0528C
1
Caution
INSTALLATION AND OPERATING INSTRUCTIONS
Prior to the installation of this product, the installation instructions should be read and completely understood. The
installation instructions must be read to prevent personal injury and property damage. Keep these installation instructions
in an easily accessible location for future reference.
CAUTION: The maximum load capacity is 165 lbs. Use with products exceeding the maximum load capacity may cause
serious injury. See apparatus instructions.
Recommended mounting surfaces: wood stud and solid-flat concrete. If the mount is to be installed on any surface other
than wood studs, use suitable hardware (not included but commercially available).
Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to do so could result in
damage to the display and/or damage to the mounting surface.
Do not install near heater, fireplace, air conditioning,in direct sunlight, or any other heat producing source. Failure to do so
may result in damage to the display and could increase the risk of fire.
The wall structure must be capableof supporting at least the maximum load capacity as indicated. If not, the wall must be
reinforced. Proper installation procedure by yourself or a qualified service technician, as outlined in the installation
instructions, must be adhered to. Failure to do so could result in serious personal injury.
When mounting to a wall that contains wood studs, confirm dead center of the wood stud prior to installation, it is
recommended that the wood studs be a minimum of 16" apart.
It is recommended that two people perform the installation. Injury and/or damage can result from dropping or mishandling
the display.
Hardware kit:
(×4) M4×12 screw
AG
(×4) M4×16 screw
BH
(×4) M5×16 screw
CI
(×4) M6×16 screw (×6) M8x80 Bolt
DJ
(×4) M8×16 screw
EK
(×4) M4×35 screw (×6) M8 Washer
FL
M
(×4) M6×35 screw
(×4) M8×35 screw
(×4) M8/M6/M5 Washer
(×6) M8 concrete anchor
(×4) M8 Spacer
2
-
Tools Required:
Phillips head screw driver
1
Stud finder for drywall installation
2
5/16" Socket and Wrench
3
Electric drill and 5/16" (8mm) masonry bit for concrete/brick installation
4
Note: Please ensure that the bubble level is properly mounted on the wall plate prior to mounting the wall
plate.
Step1: Wall Plate Installation
a) Wood Stud Installation
NOTE: When mounting to wood studs, the two wood studs must be a minimum of 16" apart.
1
Use a high-quality electronic stud finder (commercially available) to
locate dead center of two studs and mark their locations with a pencil
(figure 1-a).
2
With the help of an assistant, and using the bubble level to ensure the
wall plate is level, position the wall plate against the wall in the desired
mounting location.
Mark the right (upper and lower) and the left (upper and lower) positions
3
of the small horizontalslots that are in alignmentwith the studs (figure 1
b).
You should mark four positions total.
4
Next, pre-drill a 1/4" hole to a depth of 2" in the wall stud at each
5
marked location.
Place the wall plate against the wall and line up the mounting slots with the drilled holes. Check the bubble level to verify
6
that the wall plate is level.
For each location, insert a lag bolt (J) and washer (L) into the wall
7
Tighten the bolt with an open ended socket wrench by turning clockwise until tight.
8
CAUTION: Do not over-tighten bolts-doing so many cause unnecessary damage to the wall. Avoid excessive torque.
CAUTION: Do not release the wall plate until it is properly mounted and secured to the wall.
3
Loading...