SIIG 04-0207A User Manual

Low Profile PCI-1S1P
Quick Installation Guide

Introducing the Low Profile PCI -1S1P

The Low Profile PCI -1S1P conforms to the new PCI card form factor
standard made for space constrained system designs.

Features and Benefits

• Conforms to PCI v2.2 Plug and Play

• Full support for DOS- and Windows-based software

• IRQ sharing feature eliminates IRQ conflicts
Serial interface:

• High-speed 16550 UART serial port (9-pin) supports baud rates

up to 920Kbps. Works with various types of serial devices

• Built-in 16-byte FIFO buffers dramatically increase data transmit/

receive speed

Parallel interface:

• Conforms to IEEE 1284-1994 parallel port standard

• High-speed parallel port supports various types of parallel port

devices

• Supports EPP, ECP(PIO mode), Bi-directional Parallel Port (BPP)

and Standard Parallel Port (SPP) modes

Dimensions:

• PCB: 119.91 mm (L) x 64.41 mm (H)

• Bracket: 18.42 mm (W) x 79.20 mm (H)

System Requirements

• Pentium or equivalent computer with an available 32-bit PCI slot

• DOS/Windows 3.1x, Windows 95/98/98 SE/ME/NT 4.0/2000

04-0207A

1

Package Contents

• One Low Profile PCI -1S1P board

• One Driver Installation diskette

• One 5-year warranty card

• This quick installation guide

Hardware Installation

General instructions for installing the card are provided below,
since the design of computer cases and motherboards vary. Refer
to your computer’s reference manual for further information, if
needed.

Static Electricity Discharge may permanently damage your system.
Discharge any static electricity build up in your body by touching
your computer’s case for a few seconds. Avoid any contact with
internal parts and handle cards only by their external edges.

1. Turn OFF the power to your computer and any other
connected peripheral devices. Unplug the computer's power
cord.

2. Remove your computer’s cover and install the card in an
available PCI slot.

3. Push the board down firmly, but gently, until it is well seated.

4. Secure the card and replace the cover.

Software Installation

This section provides information on how to install the
Low Profile PCI -1S1P's drivers for the following operating systems:

Windows 95/98/98 SE/ME
Windows NT 4.0
Windows 2000
DOS/Windows 3.1x

Windows 95:

1. At the Add New Hardware Wizard windows, click Next.

2. Insert the Driver Installation diskette in the floppy drive, and
click Other Locations. Type in a:\Win95, click OK, then
Finish.

2

3. From the Insert Disk window, click OK. When the Copying
Files dialog box appears, type in a:\Win95, then click OK.

4. Remove the diskette and select Yes to restart the computer for
the setup to take effect.

Windows 98/98 SE:

1. At the Add New Hardware Wizard windows, click Next.

2. Select Search for the best driver for your devices
(Recommend), then click Next.

3. Select Specify a location, insert the Driver Installation diskette
and type in a:\Win98, then clickNext.

4. Click Next, then Finish.

5. Remove the diskette and click Yes to restart your system.

Windows ME:

1. At the Add New Hardware Wizard screen, choose Specify the
location of the driver (Advanced), then click Next.

2. Check Specify a location, insert the Driver Installation diskette
into your floppy drive, type in A:\Win98, then click Next.

3. Click Next, and Finish to complete driver installation.

4. Remove the driver diskette and click Yes to restart Windows.

To verify successful installation in Windows 95/98/98 SE/ME:

1. From the main desktop, double click My Computer, Control
Panel, System, then click Device Manager.

2. Double click Ports (COM & LPT) and new Cyber PCI ports
should be displayed. Also, double click SIIG Cyber PCI
option and SIIG ... PCI Board should be displayed.

The board is ready to connect new devices.

Windows NT 4.0:

1. From the desktop click Start, then Run.

2. Insert the Driver Installation diskette, type in A:\NT4\setup,
then click OK.

3. Click Next when the Welcome window appears.

3