SII LP-2050-MF, LP-2050, LP-1030-MF, LP-1030 Quick Reference Manual

Wide Format Printer
Teriostar LP-2050 Series

LP-2050

Multifunction Model

Printer Model

LP-2050-MF

To operate your Printer correctly, read this manual

carefully bef ore use.

After reading the manual, keep it in a place where you

can access it when required.

Quick Reference Guide

U00121382802

Your Printer is a Teriostar LP-2050 Series Wide Format Printer.

This manual describes the basic operation methods for both the LP-2050 and LP-2050-MF

models. For more detailed information, see the User's Manuals on the supplied CD-ROM.

Preface

Turning the Power On/O …………………… 3

Power On ……………………………………………… 3

Power O ……………………………………………… 3

Mode Buttons ………………………………… 3

Replacing the Paper …………………………… 4

Replacing the Toner Cartridge ………………… 6

Replacing the Waste Toner Bottle …………… 8

Replacing the Charger Unit …………………… 10

Replacing the Process Cartridge ……………… 12

Part Names ……………………………………… 14

Paper Jams ……………………………………… 16

Copying

MF

………………………………… 20

Importing Images (Documents) to a Computer

MF

21

Operating the Printer from a Computer

MF

23

Troubleshooting ……………………………… 24

When an Error Message Appears …………………… 24

Smears on a Printout ……………………………… 24

Changing the Time Until Power Save Mode ……… 24

Automatic Paper Cutting After a Certain Time …… 24

Automatic Paper Cutting After Opening

and Closing a Door ………………………………… 25

Changing the Print Density ………………………… 25

Wrinkles on Tracing Paper ………………………… 25

Selecting Paper to Match the Print Data …………… 25

Missing Print or Slow Data Reception ……………… 26

Service Representatives ……………………… 29

Disposal Method …………………………………… 29

Table of Contents

3

Turning the Power On/Off

Power On

12

Power O

Press down for

1 sec. or longer

2

1

zCOPY button

MF

Changes to copy mode, and the lamp at the button's

left lights up. For more details, see the separate User's

Manual for Multifunction Printer Operation.

zSUBMIT button

MF

Changes to submission mode, and the lamp at the

button's left lights up. For more details, see the separate

User's Manual for Multifunction Printer Operation.

zSCAN button

MF

Changes to scan mode, and the lamp at the button's

left lights up. For more details, see the separate User's

Manual for Multifunction Printer Operation.

zPRINT button

Changes to print mode and enables printing.

zMENU button

Changes to menu mode, which enables the Printer

setting specication.

Mode Buttons

4

Replacing the Paper

1

2

3

4

5

6

OkNo

7

5

TReplacing the Paper

8

60 cm
(23.63 inches)

9

10

Approximately 90°Approximately 90°

11

6

Replacing the Toner Cartridge

1

2

3

4

x10

x10

5

6

7

Disposing of Empty Toner Cartridges

Put the used toner cartridge into the bag provided in the box of the new toner cartridge, and dispose

of it according to the local regulations.

TReplacing the Toner Cartridge

7 8

8

Replacing the Waste Toner Bottle

1 2

x10

3

①

②

4

9

Disposing of Used Toner Bottles

Dispose of the waste toner bottle according to the local regulations.

TReplacing the Waste Toner Bottle

5

6

①

②

7

10

Replacing the Charger Unit

1

Press down for

1 sec. or longer

2

3

4

5

6

7

11

TReplacing the Charger Unit

8

9

10

11

TIP

The charger unit can be installed in

either direction.

If lines or other defects appear on

the printout, inverting the charger

unit right and left sides may solve the

problem.

12

Replacing the Process Cartridge

1

Press down for

1 sec. or longer

2

3

4

5

6

7

8

9

13

TReplacing the Process Cartridge

10

x5x5

11

12

13

①

②

①

③

②

14

15

①

②

③

16

14

Part Names

Front door

Drawer for rolls 1 and 2

Drawer for rolls 3 and 4

Printer Model

Multifunction Model

Document table

Toner door

Scanner cover

Front Side

15

Process cartridge drawer

Fuser unit drawer

Filter cover

Waste toner door

Paper outlet slot

Latch button

Paper outlet cover

Rear Side

TPart Names

16

The door requiring action is displayed, in

accordance with the paper jam location.

Open the specied door and take the appropriate

action to remove the paper jam.

Paper jam in a Roll paper drawer

1

2

3

Paper jam in the front door

1

Paper Jams

17

2

3

Paper jam in the Fuser unit

1

2

When you cannot pull out the paper
easily:

①

②

3

TPaper Jams

18

Paper jam in a roll paper drawer or front

door

1

2

3

4

5

6

TPaper Jams

19

7

8

Original jam

MF

1

2

3

4

5

TPaper Jams

20

Press COPY

Set the original

Position the original facing down. Set it in the Printer

aligned with the original width guide. The inserted original

is automatically pulled into the Printer, and set.

Copying

MF

21

Importing Images (Documents) to a Computer

MF

1

Double-click TerioStation.

2

Click the Scan tab.

3

Click Save Folder.

4

Select the destination folder to save the scanned

data. Click OK.

5

Click Scan.

22

6

Click Preferences.

7

Input the Printer IP address in the Assign host

name/IP address eld. Click OK.

8

Set the scan conditions, and then click Scan.

9

Load the original.

Important

If "Scanner is operating in another mode" is displayed, press SCAN on the operation panel.

If "Color processing is not supported because the scanner being used is a dedicated monochrome

device" is displayed, you cannot scan in color mode.

TImporting Images (Documents) to a Computer

MF

23

Operating the Printer from a Computer

MF

1

Start the web browser and enter "http://(IP address set on the Printer)" in the

address eld. Press Enter.

2

Click English.

3

Click an item from the left menu to check the settings or Printer status.

24

When an Error Message Appears

Take the action specied by the panel message.

Or see the User's Manual for Basic Printer

Operation, Chapter 4.

Smears on a Printout

Replace the process cartridge. (& page 12)

Changing the Time Until Power Save
Mode

Set Time Before Power Save in the Printer Engine

menu.

Menu

Printer Engine

Time Before Power Save

15 minutes

or

30 minutes

or

60 minutes

or

90 minutes

or

235 minutes

Automatic Paper Cutting After a Certain
Time

Set Top Cut Timer in the Printer Engine menu.

Menu

Printer Engine

Roll 1 Top Cut Timer

or

Roll 2 Top Cut Timer

or

Roll 3 Top Cut Timer

or

Roll 4 Top Cut Timer

O

or

30 minutes

or

1 hour

or

2 hours

or

4 hours

or

1 minute

or

5 minutes

or

10 minutes

Troubleshooting

25

Automatic Paper Cutting After Opening
and Closing a Door

Set Top Cut at Door Open to On in the Printer

Engine menu.

Menu

Printer Engine

Top Cut at Door Open

On

Changing the Print Density

Set the Print Density in the Printer Engine menu.

Menu

Printer Engine

Print Density

Low

or

Slightly Low

or

Normal

or

Slightly High

or

High

Wrinkles on Tracing Paper

Set Humidity for Tracing Paper to High Humidity in

the Printer Engine menu.

Menu

Printer Engine

Humidity for Tracing Paper

High Humidity

Selecting Paper to Match the Print Data

Select Optimal at Paper Supply Mode.

Menu

PDL settings

Select the port and format

Paper Parameters

Paper Supply Mode

Optimal

TTroubleshooting

26

Missing Print or Slow Data Reception

Change the driver settings.

1

In Start Menu, open Devices and Printers.

2

Right-click the SII LP-2050 icon, and then

click Printing Preferences.

3

Click the Options tab.

4

Click Change in the operation mode of

the driver.

5

Change the output process selection from

Process with Printer to Process with

Computer. Click OK.

6

Click Apply.

TTroubleshooting

27

7

Click OK.

8

Print.

If the symptom persists, perform the

following setting operation.

If the problem persists:

1

Perform steps 1 to 4 and open Driver

Operation Mode.

2

Set the resolution of the printer driver to

200dpi or 100dpi. Click OK.

TTroubleshooting

28

3

Click Apply.

4

Click OK.

5

Print.

The User's Manuals and driver are on the supplied CD-ROM.

TTroubleshooting

29

Service Representatives

SIIT oers support to ensure you get the most from your Teriostar LP-2050 Series Printer. For details,

contact your dealer or nearest service representative.

http://www.seiko-i.com/

Disposal Method

Dispose of the used toner cartridges and waste toner bottles according to the local regulations.

U00121382802 July, 2013

Seiko I Infotech Inc., 2013

All rights reserved.

The contents of this manual may be changed without prior notice.

is a registered trademark of Seiko Instruments Inc.

1-8, Nakase, Mihama-ku, Chiba-shi, Chiba, 261-8507, Japan

TEL: [phone]

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.

The CE mark, that shows that the products sold in the EU are conformed to the requirements of EC directive,
is statutorily obliged to be axed to the products.
In each directive, the scope of directive to be applied to equipment is explicitly dened. Our company’s
product LP-2050 series conforms the EMC directive (2004/108/EC), low voltage directive (2006/95/EC) and
RoHS Directive 2011/65/EU.

Inquiry of CE mark:

Seiko Instruments GmbH

Siemensstraße 9, D-63263 Neu-Isenburg
Germany
Tel: [phone]
Fax: + 49 - 6102-297-320

Seiko I Infotech Inc.

8 Nakase 1-chome, Mihama-ku, Chiba-shi, Chiba 261-8507, Japan
Phone : [phone]
Fax : [phone]