Signify SC1500 User Manual
MSB LowB TMPix - ZB/BLE
SC1500
Installation Instructions
Instructions d’installation Istruzioni per l’installazione Installationsanweisungen 安装指示书
Instrucciones de instalación Installatie-instructies インストール手順
Installation
Instructions
43.8 mm (1.72 in)
3.3 mm (0.13 in) 1 mm (0.04 in)
4x
r = 2.5 mm (0.10 in)
(0.66 in)
16.8 mm
1 mm (0.04 in)
18.9 mm
(0.74 in)50.8 mm (2.00 in)
SC1500
SR driver
29.9 mm (1.18 in)
6.4 mm (0.25 in)
1
Stranded wire
0.3 – 0.5 mm
(AWG 20 ... 22)
Solid conductor wire
2
0.25 – 0.75 mm
(AWG 18 ... 24)
7 – 9 mm
(0.28 ... 0.35 in)
2
05
kg
0.018 kg
max
55 °C
min
0 °C
≤90%
www.philips.com/lighting4422 950 43301 25 October 2019
2
H
Y
H = Min. 2.5 m (8.2 ft)
H = Max. 4.0 m (13.1 ft)
Y
X
3
H
X
X = 5.4 m (17.7 ft)
Y = 3.6 m (11.8 ft)
X = 3.6 m (11.8 ft)
Y = 2.7 m (8.9 ft)
at H: 3 m, t: 25 °C
4
>2 m
(6.6 ft)
Design-in Guide www.philips.com/sensorbundles
Field of view
min. 0.8 × H
5
U-shaped slot in metal sheet (max. thickness 1 mm)
16 mm
(0.63 in)
43.5 mm (1.71 in)
Cut-out in metal sheet (max. thickness 0.7 mm to 1.2 mm)
r = 2.3 mm (0.09 in)
17 mm
(0.67 in)
44 mm (2.74 in)
43.5 mm (1.71 in)
D Note
Accessory mounting ring
to secure sensor to cut-out
available.
16 mm
(0.63 in)
FCC/IC compliance statement
EN
This device complies with part 15 of the FCC rules for the United States
and Industry Canada (IC) license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Any changes or modications not expressly approved by Signify could
void the user’s authority to operate this equipment. This product is
intended for commercial use only.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment.
This equipment must be installed and operated with a minimum
distance 200 mm between the radiator and your body.
IC Radiation Exposure Statement
This equipment complies with IC RSS-102 radiation exposure limits set
forth for an uncontrolled environment.
This equipment must be installed and operated with a minimum
distance 200 mm between the radiator and your body.
FCC statement: This equipment has been tested and found to
comply with the limits for a Class A digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
© 2019 Signify Holding. All rights reserved. Specications are
subject to change without notice. No representation or warranty
as to the accuracy or completeness of the information included
herein is given and any liability for any action in reliance thereon is
disclaimed. Philips and the Philips Shield Emblem are registered
trademarks of Koninklijke Philips N.V. All other trademarks are
owned by Signify Holding or their respective owners.
4422 950 43301 25 October 2019
RF Exposure Information
This device meets the EU requirements (2014/53/EU) on the limitation
of exposure of the general public to electromagnetic elds by way of
health protection. The device complies with RF specications when
the device used at 321 mm from your body.
Hereby, Signify declares that the radio equipment type SC1500 is in
compliance with Directive 2014/53/EU. The full text of the EU declaration
of conformity is available at the following Internet address:
http://www.philips.com/red
D Notes
• This device is suitable for plenum use.
• Must be powered by class 2 energy limited source for NA region or
SELV for EU region.
• Do not use damaged products
• Type 1 Action
DÉCLARATION DE CONFORMITÉ À LA FCC/IC
FR
Ce dispositif est conforme à la partie 15 des règles de la Federal
Communications Commission (FCC) des États-Unis et d’Industrie
Canada (IC) exempts de licence RSS norme(s). Son fonctionnement
est assujetti aux deux conditions suivantes: (1) Ce dispositif ne doit
pas provoquer de brouillage préjudiciable, et (2) il doit accepter
tout brouillage reçu, y compris le brouillage pouvant entraîner un
mauvais fonctionnement. Tous les changements ou modications
non expressément approuvés par Signify, sont susceptibles d’annuler
le droit de l’utilisateur à se servir de cet équipement. Ce produit est
exclusivement destiné à un usage commercial.
Cet équipement est conforme aux limites d’exposition aux
rayonnements IC établies pour un environnement non contrôlé. Cet
équipement doit être installé et utilisé avec un minimum de 200 mm
de distance entre la source de rayonnement et votre corps.
www.philips.com/lighting
Loading...