SIGNIFY Hadco CF5T, Hadco CXF5 Installation Instructions Manual

Signify North America Corporation Signify Canada Ltd.
200 Franklin Square Drive 281 Hillmount Road,
Somerset, NJ 08873 Markham, ON, Canada L6C 2S3
Telephone [phone] Telephone [phone]

ADAPTER
SCREWS

INSTALLATION INSTRUCTIONS:

CF5T, CXF5 FIXTURES

UNIVERSAL FIXTURE
ADAPTER

BALLAST TRAY
HANDLE

REFLECTOR
ASSEMBLY

BALLAST
ASSEMBLY

POWER SUPPLY
ARM WIRES

FIXTURE SUPPLY
WIRES

LENS DOOR

CAUTION

1. The electrical power must be disconnected from the fixture and pole before installing, servicing, or
relamping the fixture.

2. These directions must be read carefully and adhered to. Failure to do so may result in injury, damage to
the fixture, and voiding the warranty.

3. CF5T/CXF5 Hanging Fixture: This fixture must be hung from a Universal Fixture adapter, supplied with all
Hadco arms, or as a separate accessory to be mounted to a non-Hadco arm. See the instructions
supplied with the adapter for further information.

32001043, revision F

DROP LENS IF 5V
OPTICS AND MOGUL

(CF Series Shown)

This fixture is intended for installation in accordance with the National Electrical Code and local code
specifications. Failure to adhere to these codes and instructions may result in serious injury and/or damage
to the ballast and void the warranty. These instructions do not purport to cover all details or variations in
equipment, nor to provide for every possible contingency related to installation, operation, maintenance,
or mounting situation. Should specific problems occur that are not addressed by these instructions, contact
your Sales Representative or distributor for assistance. Retain these instructions for future reference.

SOCKET. OTHERWISE
FLAT LENS.

page 1 of 2

TOOLS REQUIRED

FOR INSTALLATION

1. Flat head screw driver - to open or close lens door.

2. Phillips head screw driver - to remove or re-install the reflector assembly and ballast assembly.

3. 5/16" Allen wrench - to assemble (2) piece clamp collar
FOR RELAMPING:

1. Flat head screw driver - To attain access to the lamp by opening the lens door.

INSTALLATION (CF5T)

WARNING - The power MUST be turned off prior to proceeding. Read these instructions carefully. If any
problems are encountered that are not covered in these instructions, contact Hadco for assistance.

STEP 1: The fixture is designed to hang from the Universal Fixture Adapter.

- To hang the fixture, first connect the power supply quick-connect on the fixture
to the quick-connect on the arm.

- Then hang the fixture per the instructions supplied with your Adapter.
* Be sure the fixture is straight and securely attached before proceeding.
STEP 2: OPEN LENS DOOR

- To open the lens door, loosen the (2) 1/4-turn studs. This allows the door to swing
open. A safety cable will prevent it from falling, should it come out of the hinge.
STEP 3: INSTALL LAMP

- Install the correct lamp based upon the lamp label next to the socket.
STEP 4: CLOSE LENS DOOR

- Close the lens door and tighten the (2) 1/4-turn studs.
STEP 5: TYPE 2, 3, or 4 OPTICS (only)

- Carefully loosen the (2) Adapter screws just enough to rotate the fixture.

- Rotate the fixture to the desired orientation.

- Then retighten the screws to lock the fixture in that position.
STEP 6: Connect the power, and test the fixture for proper operation.
STEP 7: After the installation is complet, deliver this instruction manual to the owner.

TO REPLACE LAMP

STEP 1: It is a good idea to clean the fixture each time you relamp. Avoid using harsh
solvents or abrasives while cleaning fixture.
STEP 2: Open the lens door by loosening the (2) 1/4-turn studs.
STEP 3: Remove the old lamp and dispose of it in a responsible manner.
STEP 4: Install a new lamp, referring to the lamp label next to the socket to ensure
the correct type.
STEP 5: Close the lens door and tighten the (2) 1/4-turn studs.

DISCLAIMER

While we believe these instructions to be accurate at the time of publication, Hadco reserves
the right to make changes to this fixture and/or components. The contractor should follow local
and national electrical codes where required. For any further information please contact Hadco
customer service.

32001043, revision F

page 2 of 2