Signify 9290012630X User Manual
Hue Engine V1.0
Specification item Value Unit Condition
The Hue Engine is a general purpose Zigbee certified building block for Hue
connected lighting applications e.g. Hue White, Hue White Ambiance and Hue
White and Color ambiance for lamps and luminaires. It does not work stand-alone
Description
but is meant to be SMT soldered on a application specific motherboard that
contains the proper interfacing for stand-alone usage.
Logistical data
12NC 929001263055
Minimum Order Quantity 500 PCE
Electrical input data
Vcc voltage 3.0~3.6 Volt Ripple<50 mV
Current (normal) 25 mA
Electrical output data
Average power consumption 85mW Watt
PSU wattage <60W Watt maximum wattage
Standby power <150mW
Wiring & Connections
Ground 1 GND
ADC2, e.g. for voltage sensing General purpose in/out 2
ADC1, e.g. for current sensing
to be used as ADC (e.g. NTC read-out), I2C, SPI or PWM 4 Mixed_out_1
to be used as ADC, I2C, SPI or PWM PWM_CHN1
General purpose in/out 1: E.g. for button control
General purpose in/out 2: E.g. for button controlPWM_CHN3 7GPIO2
i.e. for current source
PWM output 9PWM_CH0
PWM output 10 PWM_CH1
PWM output 11 PWM_CH2
PWM output 12 PWM_CH3
PWM output 13 PWM_CH4
Ground 14 GND
3V power in 15 VDD
Used for SW programming, UART bus communication 16 TXD
Used for SW programming, UART bus communication 17 RXD
Used for SW debugging 18 Nreset
Used for SW debugging 19 SWCLK
Used for SW debugging
Features & Functions
Hue White Color Ambience yes
Hue White Ambiance yes
Hue White yes
Dimming yes
Device diversity yes by late state configuration
Automatic color consistency yes
OTA upgrade yes Over the air upgradable when connected to the Hue Bridge
2 ADC2
3 ADC1
5 Mixed_out_2
6GPIO1
8Enable
20 SWDIO
I/O definition
Wireless specifications
Wireless RF mode frequency band 2400–2483.5 MHz MHz
Wireless communications protocol IEEE 802.15.4 ZigBee Light Link protocol
Operating channel 11 – 26 channels
Range 12 meter indoor
Frequency tolerances (Typical) +/-30 ppm Continuous single tone
Output power (Typical) 4 dBM Measured at antenna feedpoint
Spurious emissions* (Typical) -36 dBM 30 – 1000MHz
-30 dBM 1 – 12.75GHz
-47 dBM 1.8 – 1.9GHz
EVM (Typical) 15 %rms
Receiver Sensitivity (Typical) -99 dBM PER < 1%
TRP -2 dBM when mounted on a motherboard of 30x40mm (i.e. Hue Connect)
-47 dBM 5.15 – 5.3GHz
LED board requirements
Hue White Color Ambience Unified Gamut covered by L1.5 specifications
Hue White Ambiance Tunable white CCT range: 2000-6500K
Hue White 2700K / 3000K / 4000K
Tunable white CCT range: 2000-6500K
CRI > 80 for CCT 2000-4000K
CRI > 65 for CCT 6500K
R9 > 0 for CCT 2000-4000K
Color consistency: 95% within 5SDCM covered by L1.5 specifications
Minimum dim-level: 2%
CRI > 80 for CCT 2000-4000K
CRI > 65 for CCT 6500K
R9 > 0 for CCT 2000-4000K
Color consistency: 95% within 5SDCM covered by L1.5 specifications
Minimum dim-level: 2%
CRI > 80
R9 >
Color consistency: 95% within 5SDCM covered by L1.5 specifications
Minimum dim-level: 2%
Insulations
Dimensions & Weight
Length 23.5 mm ±10% tolerance
Width 18 mm ±10% tolerance
Height 3.7 mm ±10% tolerance
Fixing hole diameter NA mm
Fixing hole distance NA mm
Weight gram
Operational temperatures and humidity
Ambient temperature -10 to 50°C Celcius
Tcase-max 70°C Celcius to be measured on Hue Engine shield
Maximum housing temperature
Relative humidity Non-condensing
Storage temperature and humidity
Ambient temperature For 6 months
Relative humidity Non-condensing
Lifetime
lifetime hours
Measured temperature at Tc-point is Tcase- max.
Maximum failures = 10%
Surge capability
ESD rating +/-2 KV Contact
+/-4 KV Air
Certificates and standards
Approval marks CE, FCC, ETSI, ROHS & REACH, ZLL
Compliances and approvals
Loading...