SIGE SE2522L Datasheet
SE2522L
RangeCharger™ 2.4 GHz Power Amplifier And Power Detector IC
Preliminary Information
Applications
IEEE 802.11b DSSS radios, Wireless LAN
2.4GHz cordless phones, ISM radios
Features
Integrated power detector circuit
High linear output power for IEEE802.11b:
+20dBm, ACPR 1st lobe –30dBc, 2nd lobe –50dBc
Low current consumption: 110mA at 3.3V
High saturated output power for cordless telephone
applications: +23dBm, 140mA at 3.6V
Single supply voltage: 2.7 to 3.6V
Wide Temperature range: -40°C to +85°C
Integrated linear analog control for DC current and
output power management
Small plastic package: 8 Pin LPCC
Ordering Information
Type Package Remark
SE2522L 8 Pin LPCC Samples
SE2522L-R 8 Pin LPCC Shipped in
Tape & Reel
SE2522L-EK1 Evaluation Kit
Functional Block Diagram
Product Description
The SE2522L is a power amplifier IC designed for the
2.4GHz ISM band and compliant with the IEEE 802.11b
WLAN standard. It typically provides +20dBm linear
output power requiring only 110mA at 3.3V. It can also
be utilized in 2.4GHz cordless telephone applications
where it typically provides +23dBm saturated output
power at 3.6V.
The SE2522 includes an integrated power detector
circuit for closed loop monitoring of output power. It has
an input power range of 15dB with an accuracy of
±1.0dB. An accurate automatic level control function
can easily be implemented using this power detector
circuit.
The SE2522L contains a linear analog control (0.1 to
1.6V) for minimizing DC current consumption and
maximizing PAE.
The SE2522L includes a digital enable control for
device on/off control where ramping is typically 1 µsec.
This device is capable of operating at a duty cycle of
100 percent.
IN
Stage 1
GND
V
V
CTL
Bias Generator
V
CC0
CC1
V
EN
Stage 2
Power Detector
V
DET
OUT/ V
CC2
18-DST-01 Rev 2.4 Aug 7/02 1 of 8
RangeCharger™ 2.4 GHz Power Amplifier And Power Detector IC
Pin Out Diagram
Note: Pads and die pad shown are at the bottom of package.
SE2522L
Preliminary Information
8
7
6
5
SE2522L
Bottom View
Die Pad
1
VDET
VCTL
2
3
VEN
4
INVCC0
SE2522L
Top View
1
VDET
2
3
4
2522L
VCTL
VEN
IN VCC0
8
7
6
5
OUT/VCC2
NC
CC1
V
OUT/VCC2
NC
CC1
V
Pin Out Description
Pin No. Name Description
1 V
2
3
4 IN Power amplifier RF input, external input matching network with DC blocking is required.
5
6
7 NC No connect
8
Die Pad GND Heatslug Die Pad is ground
Analog power detector output
DET
Controls the RF output power and DC current level of the power amplifier. An analog
control signal between 0.1V and 1.6V varies the PA output power between Min. and
V
CTL
Max. values.
Power Amplifier Enable pin. A digital control signal with logic high (power up) and logic
V
EN
V
CC0
V
CC1
OUT/V
low (power down) is used to turn the device on and off.
Bias supply voltage.
Stage 1 collector supply voltage, an external inter-stage matching network is required.
PA Output and Stage2 collector supply voltage, external output matching network with
CC2
DC blocking is required.
18-DST-01 Rev 2.4 Aug 7/02 2 of 8
SE2522L
RangeCharger™ 2.4 GHz Power Amplifier And Power Detector IC
Preliminary Information
Absolute Maximum Ratings
These are stress ratings only. Exposure to stresses beyond these maximum ratings may cause permanent damage
to, or affect the reliability of the device. Avoid operating the device outside the recommended operating conditions
defined below. This device is ESD sensitive with an ESD rating of < 600V. Handling and assembly of this device
should be at ESD protected workstations.
Symbol Parameter Min. Max. Unit
VCC Supply Voltage -0.3 +3.6 V
V
Control Voltage -0.3 V
CTL
V
CC
VEN Ramping Voltage -0.3 VCC V
PIN RF Input Power +8 dBm
T
Storage Temperature Range -40 +150
STG
Tj Maximum Junction Temperature +150
°C
°C
Recommended Operating Conditions
Symbol Parameter Min. Typ. Max. Unit
TA Operating Temperature -40 +85
VCC Supply Voltage 2.7 3.3 3.6 V
DC Electrical Characteristics
Conditions: V
CC0=VCC1=VCC2=VEN
Output externally matched to 5
Symbol Parameter Min. Typ. Max. Unit
ICC Supply Current, V
I
Supply Current (sat) @ PIN = +2dBm - 140 175 mA
CC(sat)
V
PA Output Power Control Voltage Range 0.1 1.6 V
CTL
I
Current sunk by V
CTL
Logic High Voltage 2.0 V
VEN
Logic Low Voltage 0.8 V
I
Leakage Current when VEN = 0V, V
STBY
=3.3V, V
=1.6V, T
CTL
=25°C, f =2.45GHz, using IEEE802.11b modulation, Input and
A
0Ω, unless otherwise noted.
= 1.6V, PIN = -7dBm - 110 130 mA
CTL
Pin 55 100
CTL
= 0V 0.1 200
CTL
°C
µA
µA
18-DST-01 Rev 2.4 Aug 7/02 3 of 8
Loading...