Sierra Monitor Corporation PSE530 User Manual

Pressure Sensor

Operation Manual

PSE530 Series

Thank you for purchasing the SMC PSE530 Series Pressure Sensor. Please read this manual carefully before operating pressure sensor and understand pressure sensor, its capabilities and limitations. Please keep this manual handy for future reference.

SAFETY

The Pressure Sensor and this manual contain essential information for the protection of users and others from possible injury and property damage and to ensure correct handling. Please check that you fully understand the definition of the following messages (signs) before going on to read the text, and always follow the instructions.

IMPORTANT MESSAGES

Indicates a potentially hazardous situation which could result in death or serious injury if you do not follow instructions.

Read this manual and follow its instructions. Signal words such as WARNING and NOTE will be followed by important safety information that must be carefully reviewed.

Do not disassemble, remodel ( including change of printed circuit board) or repair.

An injury or failure can result.

Do not operate beyond specification range.

Fire, malfunction or sensor damage can result.

Do not operate in a combustible gas or explosive gas atmosphere.

Fire or an explosion can result. This pressure sensor is not an explosion proof type.

WARNING

OPERATOR

●This operation manual has been written for those who have

knowledge of machinery and apparatus that use pneumatic equipment and have full knowledge of assembly, operation and maintenance of such equipment.

●Please read this operation manual carefully and understand it

before assembling, operating or providing maintenance service to the pressure sensor.

NOTE

Follow the instructions given below when handling your pressure sensor. Otherwise, the sensor may be damaged or may fail, thereby resulting in malfunction.

・Do not drop it, bring it into collision with other objects or apply

excessive shock (980m/s

or more).

・Do not pull the lead wire with force nor lift the main unit by

holding the lead wire. (Pulling strength less than 23N)

・Do not insert wire nor other article into the pressure port. ・Perform wiring and cable correctly. ・Do not perform wire or cable while power is on. ・Do not wire with the same circuit of power line or high-voltage

line.

・Connect Terminal FG to the ground when using a switching

regulator obtained on the commercial market.

・Keeping from water and dust, set an air tube to the safety

area.

Attaching the connector to the lead wire

Insulation

Connector cover

20mm or more

・ Sensor wire is stripped as shown in

the right figure.

・ The Insulation of the corresponding

color shown in the following table is put into the pin of the number stamped on the connector for sensor connection to the bottom.

Installation

(addendum information)

・ It checks that the above-mentioned preparation

work has been performed correctly, and A part shown in right figure is pushed by hand and makes temporary connection.

・ A part center is straightly pushed in by tools, such as pliers. ・ Re-use cannot be performed once it connects the connector for

sensor connection completely.

・ A sensor connector cannot be taken apart for

reuse once it is crimped.If the wire arrangement is incorrect or if the wire insertion fails, use a new sensor connector.

・ When connecting the connector to

PSE200/PSE300 series, please use the connector for Sensor Lead Wire(ZS-28-C) or as below.

Connector

Connector Connecting/Disconnecting

・ When connecting the connector, insert it straight onto the pin

holding the lever and connector body between fingers and lock the connector by pushing the lever claw into the square groove in the housing until connector clicks.

・ When disconnecting the connector, push down the lever by

thumb to disengage the lever claw from the square groove. Then pull the connector straight out.

PSE200 Series PSE300 Series

Connector for Sensor Lead Wire

Lever

Output Specification

Example of Internal Circuit and Wiring

Voltage output :

1 to 5V

Output impedance :

Approx. 1k

(Analog output)

Ω

Main circuit

12 to 24V DC

Brown DC (

)

Black OUT

Blue DC

(

)

Outline with Dimensions (in mm

)

・

Please contact with each connector maker about catalogue.

Pin No.

1 2 3 4

Color of Insulation

Brown (DC (+) )

N.C.

Blue (DC (-) )

Black (IN:1 to 5VDC)

Maker

(c)Sumitomo 3M

Tyco Electronics AMP

OMRON

Model No.

37104-3101-000FL

3-1473562-4

XN2A-1430

Model No. Rated pressure range Withstand pressure Fluid Power supply Current consumption

Repeatability Effect form power supply Temperature Characteristic

Standard Cable

PSE530-

※

0 to 101MPa

1.5MPa Air, Non-corrosive gases, Incombustible gases

12 to 24VDC, ripple(p-p)10% or less (Protection against inverse connection)

15mA or less

Voltage: 1 to 5V±2%F.S. or less (Rated pressure range)

Linearity : ±1%F.S. or less Output impedance : Approx.1kΩ

±1%F.S. or less

±1%F.S. or less with standard of analog output at 18V in the range of 12 to 24VDC

±2%F.S. or less (25℃ reference）

IP40

Operation : 0 to 50℃,Storage :-10 to 70℃ (No condensation, No freezing)

1000VAC, 50/60Hz, 1minute (Between lead block and case)

5MΩ or more 500VDC (Between lead block and case)

10 to 500Hz smaller one 1.5mm or 98m/s

double amplitude, 2 hours each in direction

of X, Y and Z

980m/s2 3times each in directions of X ,Y and Z respectively

CE MARKING

Halogen free heavy insulation cable, φ2.7, 0.15mm2, 3wire, 3m

500kPa

PSE531-

※

0 to -101kPa

PSE532-

※

0 to 101kPa

PSE533-

※

-101 to 101kPa

Analog output

Voltage output

Enclosure Ambiebt temperature Withstand voltage Insulation resistance

Vibration proof Impact proof

Environment

Model No. Port size

Piping Specification

Material

M5×0.8

Body : SUS303

41g

Body : PBT

38g

3.8g

Sensor pressure sensing part : Silicon O-ring : NBR

R06

φ6 Reducer

R07

1/4inch Reducer

Weight

With cable(3m) Excluding cable

Specification

How to connect the cable for sensor.(Optional)

Pick with fingers the hemale connector of cable for sensor. Insert it paying attention of connector direction.

Sensor

Male connector

Female connector

Cable for sensor have connector cover in order to prevent fall of female connector. Paying attention for connector cover direction, install on the sensor, rotate clockwise, and lock it. To remove cable for sensor, rotate the connector cover anticlockwise, relese lock, and remove connector cover. After removing connector cover, pick with female connector with fingers and pull out.

Unlock

Lock

Sensor

Connector cover

URL http://www.smcworld.com

PSE53 -M5

3.4

5.4

7.2

PSE53 -R06

R07

3.4

5.4

Model No. PSE53 -R06 PSE53 -R07

When connect cable for sensor

7.2

Applicable port size(D)

2.7

10.4

6mm

1/4inch

9.8

29.4

27.2

45.5

43.3

5 5.5

M5 0.8

Pressure port

2.5

Pressure port