Siemens Aktiengesellschaft 6021318 Users Manual
WIRELESS TAG DRIVE
User Guide
Benutzerhandbuch
FCC ID: SCF6021318
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Modifications not expressly approved by this company could void the user's authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protec-
tion against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
This device and its antenna must not be co-located or operating in conjunction with any other antenna
or transmitter.
This device has been designed to operate with the antennas listed below, and having a maximum gain
of 6 dB. Antennas not included in this list or having a gain greater than 6 dB are strictly prohibited for
use with this device. The required antenna impedance is 50 ohms.
IC: 10971A-6021318
This device complies with Industry Canada licence-exempt RSS standards.
Operation is subject to the following two conditions: (1) This device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
This device has been designed to operate with the antennas listed below, and having a maximum gain
of 6 dB. Antennas not included in this list or having a gain greater than 6 dB are strictly prohibited for
use with this device. The required antenna impedance is 50 ohms.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
Ce dispositif a été conçu pour fonctionner avec les antennes indiquées ci-dessous, et
ayant un gain maximum de 6 dB. Il est strictement interdit d’utiliser les antennes ne figurant pas dans
cette liste ou présentant un gain supérieur à 6 dB avec ce dispositif. L’impédance d’antenne requise
est 50 ohms.
Use the following Agilion Antennas only:
• Omni/2dBi/FME-M
• Omni/6dBi/N-F/360°
Table of contents
English
1 Functionality ................................................................................................................. 2
2 Layout and Connections ............................................................................................... 3
2.1 Connectors and Indicators ........................................................................................ 4
2.2 Pin-Assignment ......................................................................................................... 4
3 Initial operation and Usage ......................................................................................... 5
4 Troubleshooting ........................................................................................................... 6
4.1 General errors ........................................................................................................... 6
5 Technical data............................................................................................................... 7
6 Declaration of Conformity ............................................................................................. 8
20130314-6021318-UM 1
EN
1 Functionality
The WIRELESS TAG DRIVE is localized in Agilions WIRELESS LOCATION SYSTEM. It is attached to
vehicles or devices to determine the position or presence in a defined room. The transmission of
additional application specific data from and to the mobile tags is possible optionally.
The WIRELESS TAG DRIVE is designed for use in vehicles with 24 V power supply.
2 20130314-6021318-UM EN
137,4
mm
2 Layout and Connections
P1
Fuse
Antenna (P3)
(RP-SMA)
Radio-LED (D1)
Power-LED (D2)
Bus-LED (D3)
3mm
31,1mm
112mm
125,2mm
9,3mm
44,5mm
62mm
20130314-6021318-UM 3
EN
2.1 Connectors and Indicators
Connection Specification
P1 - POWER, Digital Power supply and digital inputs
P3 - Antenna RP-SMA - Antenna plug
D1 - Function-LED Blink when the WIRELESS TAG DRIVE is localized
D2 - Power-LED Lights when the WIRELESS TAG DRIVE is on, blinks on error
D3 - Bus-LED Blinks while activity at bus system
Fuse Vehicle Fuse, Mini Fuse, 5 A
2.2 Pin-Assignment
P1 - POWER, Digital - Plug
16
9
16-pol Plug WR-MPC4
0.33 mm2 to 1.31 mm2
18
Pin Description Pin Description
1 IBIS OCM 9 IBIS OC
2 IBIS RM 10 IBIS RD
3 IBIS CM 11 IBIS CD
4 Digital Input 3 12 Digital Input 4
5 Digital Input 1 13 Digital Input 2
6 CAN-High 14 CAN-Low
7 Digital Output 1 15 Digital Output 2
8 24 V DC (e.g. KL 30) 16 GND (e.g. KL 31)
P3 - Antenna - RP-SMA plug
Pin Description
1 Antenna
Shield GND, Shield
4 20130314-6021318-UM EN
Loading...