Siemens WT46S592AU User Manual

1 2 3 4 5

ˎ,ü@°CA

Low Heat

Reduced temperature for delicate fabrics ', for a longer drying

time; e.g. acrylic, polyamide, elastane or acetate silk.

ˎ@ Easy Iron Reduces creasing and prolongs the anti-creasing phase after the

programme has finished; can be selected in one of two levels.

Status indicators

Icc+cc\

Indicators which show the programme sequences. Drying, Iron Dry, Cupboard Dry, End / Easy Iron.

Service indicators

4 clean

. container

u water tank

Clean the fluff filter and/or air cooler apage 6.

Empty the condensation container.

Fill the water tank with distilled water apage 9.

For selecting the settings.

ˎMenu

For changing all the settings in the display panel.

ˎChange 

1 -24 hrs End of the programme after ... (depending on the programme selected, e.g. 1:54h a 2h;

you can always select up to the next full hour).

Electronic start timer



0, 1, 2, 3, 4 There are four buzzer volume settings: 0 (off), 1 (quiet), 2 (normal), 3 (loud), 4 (very loud). Signal

On-Off Provides protection against unintentional changes to the functions set

(press and hold the

Menu button for 5 seconds).

Appliance lock

(depending on the model)

0, 1, 2, 3

The drying result (e.g. cupboard dry) can be increased in three stages (1 - 3) for the programmes

Ê Cottons, Easy-Care and Rapid 40 a presetting = 0.

After one of these programmes has been finely adjusted, the setting is retained for the others.

Fine adjustment Drying result

600-1800 ²The spin speed that was used in the washing machine;

for more precise indication of the projected drying duration only.

Spin speed



... and adapt to individual requirements

Never operate the dryer if it is damaged. Inform your after-sales service.

Inspecting

the dryer

Sorting and loading laundry

Remove all objects from pockets. Pay particular attention to cigarette lighters. The drum must be empty before filling.

If necessary, fill the water tank for

Steam Refresh/Drying programmes a page 8.

See programme overview on page 7. See also separate instructions for basket for woollens

(depending on the model)

Your new dryer

Congratulations! - You have chosen a modern, high-quality domestic appliance from Siemens.

A distinctive feature of the condensation dryer is its low energy consumption. Every dryer which leaves our factory is carefully checked to ensure that it functions correctly and is in perfect condition. Should you have any questions, our after-sales service will be pleased to help.

Environmentally-responsible disposal

Dispose of packaging in an environmentally-responsible manner. This appliance is designated according to European directive



2002/96/EC which governs waste electrical and electronic equipment (WEEE).

This directive provides the framework for the EU-wide collection and reuse of used appliances.

For further information about our products, accessories, spare parts and services, please visit: www.siemens-home.com

Intended use

Contents Page

ʋPreparation . . . . . . . . . . . . . . . . . . . . . . 2

ʋSetting the programmes . . . . . . . . . . . . . 2

ʋDrying . . . . . . . . . . . . . . . . . . . . . . . . 3/4

ʋNotes on laundry . . . . . . . . . . . . . . . . . . 5

ʋCleaning and care . . . . . . . . . . . . . . . . . . 6

ʋOverview of programmes . . . . . . . . . . . . 7

ʋShort spin / Refresh . . . . . . . . . . . . . . 8/9

ʋInstallation . . . . . . . . . . . . . . . . . . . . . . 10

ʋFrost protection / Transport. . . . . . . . . . 10

ʋTechnical data . . . . . . . . . . . . . . . . . . . 11

ʋOptional accessories . . . . . . . . . . . . . . . 11

ʋWhat to do if... / After-sales service . . . .12

ʋSafety instructions . . . . . . . . . . . . . . . . 13

Preparing for installation, see page 8

Selecting and adjusting the programme

Additional functions

Select the drying programme ...

Press the  Start button

Only if your hands are dry. Only hold the plug by the plug casing.

Connecting the

mains plug

Display panelProgramme selector

All buttons are sensitive, a light touch is enough!

Display for max. load capacity for selected programme

ʋonly for domestic use.

ʋonly to be used for drying, refreshing or unwrinkling

fabrics that have been washed with water.

Do not leave children unsupervised near the dryer. Keep pets away from the dryer.

Drying / Short spin /

Refresh

Drying

Emptying condensation

Empty the container after each drying cycle, not during drying!

1. Remove the container, holding it level.

2. Pour out condensation.

3. Push the .ccontainer back in until it clicks into place.

Cleaning the fluff filter

1. Open the door, remove the filter and fold open.

2. Remove the fluff (by wiping the filter with your hand).

3. Close the filter, insert it again and close the door.

4. Remove fluff from the door and the area around it.

Very dirty or blocked filters should be rinsed under warm water, and then dried thoroughly.

Clean the filter in the water tank if it is dirty

1. Remove the condensation tank.

2. Remove the filter.

3. Clean the filter under running water.

4. Re-insert the filter and push in the condensation tank until it clicks into

place.

Switching off the dryer

Turn the programme selector to Off. Do not leave damp laundry in the dryer.

Removing the laundry

The automatic Easy Iron function moves the drum at certain intervals. The load remains loose and soft for

an hour (or two hours if you manually select the @ Easy Iron function, depending on the model.)

Information on laundry ...

Labelling of fabrics

Follow the manufacturer's care information.

(Drying at normal temperature.

'cDry at a low temperature a select , @°CAüLow Heat as well.

)cDo not machine dry.

Do not tumble-dry the following fabrics:

 Airtight fabrics (e.g. rubber-coated fabrics).

 Delicate materials (silk, curtains made from synthetic material) a they may crease.

 Oil-stained laundry.

Drying tips

 To ensure a consistent result, sort the laundry by fabric type and drying programme.  Close zips, hooks and eyes, and do up any buttons.

Tie belts, apron strings etc. together.

 Do not overdry easy-care laundry a risk of creasing

Allow laundry to finish drying in the air.

 Do not iron laundry immediately after drying, fold items up and leave for a while

a the remaining moisture will then be distributed evenly.

 Knitted fabrics (e.g. T-shirts, jerseys) often shrink slightly the first time they are tumble-dried.

a Do not select the Cupboard Dry Extra ++ programme.

 Starched laundry is not always suitable for dryers a starch leaves behind a coating that

adversely affects the drying operation.

 When washing laundry that is to be tumble-dried afterwards, dose the fabric softener

according to the manufacturer's instructions.

 With a small load, use the Timed Program.

Tips for Short spin/refreshing

 Use your dryer for unwrinkling and refreshing fabrics.  Short spin cycle for reducing creasing.  Refresh cycle for eliminating odours from fabrics.

Do not use Short spin/Refresh for the following fabrics:

 Wool, leather, fabrics with metal, wooden or plastic parts.  Wax and oil jackets.

 Sort the laundry by colour and put on separate short spin/refresh cycles to prevent the

colours from bleeding.

 These programmes do not remove stains a stains must be treated and removed

beforehand.

 For best results, so that the laundry will have as few creases as possible, remove each item

immediately after the programme has finished and hang on a hanger to finish drying. Pull clothes into shape if required.

Environmental protection/energy-saving tips

 Before drying, spin the laundry thoroughly in the washing machine a the higher the spin

speed, the shorter the drying time will be (consumes less energy), also spin easy-care laundry.

 Use the maximum recommended capacity, but do not exceed it

aPage 7, Programme overview.

 Make sure the room is well ventilated during drying.

 Clean the fluff filter after each drying cycle apage 4.

 Keep the air cooler clean apage 6 Cleaning and care.

 Keep the supply of cool air unobstructed a Do not cover or block the cooling grill.

Condensation container

Control panel

Air inlet

Fluff filter

Drum

Cleaning and care

Dryer housing, control panel, air cooler, moisture sensors

 Wipe with a soft, damp cloth.  Do not use harsh cleaning agents and solvents.  Remove detergent and cleaning agent residue immediately.  During drying, water may collect between the door and seal. This does not affect your

dryer's functions in any way.

Clean the protective filter 3 - 4 times a year

or if

4 flashes after the fluff filter has been cleaned.

Air cooler / protective filter

When cleaning, only remove the protective filter. Clean the air cooler behind the protective filter once a year.

 Allow the dryer to cool.  Residual water may leak out, so place an absorbent towel

underneath the maintenance door.

1. Unlock the maintenance door.

2. Open the maintenance door fully.

3. Turn both locking levers towards each another.

4. Pull out the protective filter/air cooler.

Do not damage the protective filter or air cooler. Clean with warm water only. Do not use any hard or sharp-edged objects.

5. Clean the air cooler thoroughly. Allow to drip dry.

Clean the seals.

7. Re-insert the protective filter/air cooler,

with the handle facing down.

8. Turn back both locking levers.

9. Close the maintenance door until the lock clicks into place.

Moisture sensors

The dryer is fitted with stainless steel moisture sensors. The sensors measure the level of moisture in the laundry. After a long period of operation, a fine layer of limescale may form on the sensors.

1. Open the door and clean the moisture sensors with a damp sponge which has a rough surface.

Do not use steel wool or abrasive materials.

Cover for steam nozzle in the drum

After lengthy operation, limescale and fluff may accumulate on the cover of the steam nozzle. Clean regularly:

1. Open the door and remove the cover with a screw driver. Clean the cover under running water.

2. Push and click the protective cap back in place.

Cover for steam nozzle

Air cooler

Programme end once \ lights up in the display.

Interrupt programme removing or adding laundry.

The drying cycle can be interrupted for a brief period so that laundry may be added or removed. The selected programme must then be continued until it is finished.

Hot steam may escape during the Steam Drying / Steam Refresh programmes.

1. Open the door. The drying cycle is paused.

2. Remove or add laundry and close the door.

3. If required, select a new programme and additional functions.

4. Press the Start button.

Water tank filling hole with filter

Only when switched off!

Programme overview see also pages 5 and 8

After drying ...

T-shirt

Shirts

Trousers

Skirts/dresses

Sportswear

Work clothing

Anoraks

Terry

Bathrobes

Underwear

Socks

Bed linen

Table linen

Terry towels

Tea towels/

hand towels

c

iron



lightly iron

do not iron

mangle

Ê Cottons

max. 8 kg

For whites and coloureds made of cotton or linen.

Iron Dry 

Cupboard Dry +

Cupboard Dry Extra ++

ø@

è*è*è*è*è*è*è*è*

è*è*è**è*è*

*è*è*è**è*è*

 Easy-Care

max. 3.5 kg For non-iron laundry made of synthetic fibres and mixed fabric, cotton.

Iron Dry  øc

Cupboard Dry +

Cupboard Dry Extra ++

@

è*è*è*è*è*è*

@è*è*

@è*è*è*

v Steam Drying

For smoothing hard-wearing and easy-care fabrics. Steam smooths the fabrics.

Minimum Iron Daily @max. 2.5 kg

Further information a Page 8.

Minimum Iron Shirts @

max. 1.5 kg

v Steam Refresh

For freshening hard-wearing and easy-care fabrics. Steam freshens up the fabrics.

Business g

max. 1.5 kg

Further information a Page 8.

Casual \max. 1.0 kg

 Outdoor

max. 1.5 kg

For fabrics with membrane coating, waterproof fabrics, functional clothing, fleece (jackets/trousers with removable inner lining are to be

dried separately).

É Drying basket

max. 1.5 kg

Use with the separate basket only. See the basket for woollens description.

 Delicates

max. 1 kg

For lingerie made of synthetic fibres, cotton or blended fabric.

 Rapid 40

max. 2 kg

For laundry that needs to be dried quickly, e.g. items made of synthetic fibres, cotton or mixed fabrics. The values may differ from those

given depending on the type of fabric, composition of the laundry to be dried, the residual moisture in the fabric and size of the load.

 Timed Program

warm

max. 3 kg

For pre-dried, multi-layered delicate fabrics made of acrylic, or small, individual items of laundry. Also for subsequent drying.

1110 / 9000548050

*548050*

Siemens Electrogeräte GmbH

Carl-Wery Str. 34

81739 Munich/Germany

WT46S592AU

Drying - Steam Refresh

Steam programmes for unwrinkling or refreshing

 Your dryer has unwrinkling and refreshing programmes that can be used for removing

odours and minimising creasing in dry fabrics. Steam smooths and freshens up items of

clothing.  Sorting the laundry according to size, weight, fabric and colour is necessary.  Only use Short spin/Refresh for fabrics with the same properties.  During steam generation (required), additional noises may occur.  The result of refreshing and unwrinkling may vary depending on the type of fabric, size of

the load and programme selected.  After unwrinkling or refreshing, all fabrics must be removed immediately and hung crease-

free on a hanger or a washing line for 15 minutes.

Programmes

Please observe the treatment symbols and manufacturer's instructions on the fabrics. Do not use Short spin/Refresh for fabrics made of wool, leather, containing metal or wooden parts as well as wax and oil jackets! Do not use any dryer cleaning sets!

Drying

Minimum Iron Shirts @

Suitable for easy-care fabrics, e.g. formal shirts. Fabrics are smoothed. You can expect optimum results if non-iron appears on the care label. After the programme has finished, the items must be removed immediately and hung crease-free on a hanger or washing line for 15 minutes. The programme is for up to 5 formal shirts.

Minimum Iron Daily @

Suitable for hard-wearing cotton fabrics, e.g. bed linen, tablecloths or formal shirts. Fabrics are smoothed. You can expect optimum results if non-iron appears on the care label. After the programme has finished, the items must be removed immediately and hung crease-free on a hanger or washing line for 15 minutes. The programme is for up to 5 formal shirts or 1 to 2 larger items.

Steam Refresh

Business g

Suitable for refreshing suits, jackets and trousers, or dry-clean items that cannot be washed

in the washing machine a see the care label. The programme only refreshes fabrics and

does not clean them. After the end of the programme, the items must be removed immediately. Programme for 1 suit or 1 to 2 smaller items.

Casual \

Suitable for refreshing casual wear made of cotton or artificial fibres. Fabrics must be

suitable for dryers a see the care label. The programme refreshes fabrics only, and does

not clean them. After the programme has finished, the fabrics must be removed immediately. Programme for 1 pullover, 2 pairs of trousers or formal shirts.

Drying - Steam Refresh

Your water tank empties automatically after the programme has finished.

Cleaning is therefore not required

Filling the water tank:

Fill the dryer's water tank with distilled water before every Drying - Steam Refresh cycle.

Move the programme selector to

Drying or Steam Refresh.

The u symbol appears in the display.

2. Remove the condensation tank completely.

Before every Drying - Steam Refresh cycle, fill the water tank with distilled water only. Do not use tap water, condensation or additives.

3. Fill the water tank. Use the jug supplied.

If the water tank filter is dirty a

clean the filter in the water tank.

See page 4.

4. Pour the distilled water into the filling hole on the water tank,

until the u symbol goes out on the display panel.

If drying the recommended load, approximately 250 to 300 ml of distilled water is used in the Drying - Steam Refresh programmes.

5. Insert the condensation container all the way.

6. Start the Drying or Steam Refresh programme.

Installation

 Scope of delivery: dryer, installation and instruction manual, jug, basket for woollens

(depending on the model).

 Check dryer for transport damage.  The dryer is heavy. Do not attempt to lift it on your own.  Be careful to avoid sharp edges.  Do not install in a room where there is a risk of freezing. Freezing water may cause damage.  If in doubt, have the appliance connected by a specialist.  Do not lift the dryer by protruding parts (e.g. the door) - risk of breakage.

Setting up the dryer

 The appliance plug must always be accessible.  Ensure that the appliance is installed on a clean, level

and firm surface.

 Keep the cooling grille on the front of the dryer

clear.  Keep the area around the dryer clean.  Level the dryer using the threaded feet.

Use a spirit level.  Do not remove the threaded feet under any

circumstances.

Mains connection see safety information a page 13.

 Connect to an AC earthed socket. If in doubt, have the socket checked by a specialist.

 The mains voltage and the voltage shown on the rating plate (aPage 11) must be the same.

 The connected load and necessary fuse protection are specified on the rating plate.

Converting the installed load Note the fuse protection of the socket.

10/16 Amps

Frost protection / Transport

Preparation

1. Empty the condensation container apage 4.

2. Select any programme using the programme selector.

3. Press the Start button a condensation is pumped into the container.

4. Wait 5 min., and then empty the condensation container again.

5. Turn the programme selector to Off.

The water tank must not contain any distilled water. If necessary, run the Steam/Refresh programme.

Remove all accessories from the drum. The drum must be empty.

Make sure that the air inlet remains unobstructed

Clean and level

Do not install the dryer behind a door or sliding door, which could prevent or restrict opening of the dryer door. This will prevent children from locking themselves in and putting their lives in danger.

turn to

Off

Press and hold selection then turn 3 x to the right

turn to

Off

Set amperage

1 x to the right

Feedback:

Do not operate the dryer if there is a danger of frost.

10 A

16 A

Technical data

Dimensions (DxWxH) 60 x 60 x 85 cm (adjustable height)

Weight approximately 43.5 kg Max. capacity 8 kg Condensation container 4.0 l Water tank approx. 0.4 l Connection voltage 220-240 V Connected load max. 2800 W Fuse protection 10 A / 16 A Ambient temperature 5 - 35 °C Product number

Production number

Inside of door

The rating plate can be found on the back of the dryer.

Consumption rates

These are guide values determined under standard conditions. Fluctuations up to 10% are possible.The value on the label is achieved at the maximum heat setting.

Spin speed in rpm (residual moisture)

Drying time

in min.**

Energy

consumption

in kWh**

ÊCottons 8 kg 10 A 16 A 10 A 16 A

Cupboard Dry +* 1400 (approx. 50 %) 131 105 3.74 3.74

1000 (approx. 60 %) 148 122 4.49 4.49

800 (approx. 70 %) 165 139 5.17 5.17

Iron Dry * 1400 (approx. 50 %) 109 83 2.24 2.24

1000 (approx. 60 %) 126 100 3.44 3.44

800 (approx. 70 %) 143 117 3.86 3.86

 Easy-Care 3.5 kg 1000 45 39 1.05 1.05

Cupboard Dry +* 800 (approx. 40 %) 48 42 1.35 1.35

600 (approx. 50 %) 60 51 1.65 1.65

*Test programme to DIN EN 61121 **The values may differ from those given, depending on overvoltage and undervoltage, the type of fabric, composition of the laundry to be dried, the residual moisture in the fabric and the size of the load.

Drum interior light (bulb E14, 25 W)

The drum is illuminated after the door is opened or closed, and after the programme has

started. The light goes out automatically. To change the bulb apage 12.

Optional accessories (order from the after-sales service using the order number)

Connection fittings for condensation outlet

The condensation is conveyed directly via a hose.

Washer-dryer stack connection set

The dryer can be placed on top of a suitable washing machine with the same width and depth to save space. This connection set must always be used to secure the dryer to the washing machine.

Same as WZ 20310, but with pull-out worktop.

Installation underneath the worktop

Risk of electric shock!

Instead of the appliance covering plate, you must have a metal cover fitted by an expert.

WZ 20160

WZ 20310

WZ 20300

WZ 20290

What to do if...

If you cannot rectify a fault yourself, please contact our after-sales service. We will always find an appropriate solution and will avoid unnecessary visits by engineers. Trust the expertise of the manufacturer and rest assured that the repair will be carried out by trained service technicians using original spare parts. The contact details of your local after-sales service can be found in the enclosed after-sales service directory, or by calling one of these numbers:

 GB 0844 8928999 (Calls from a BT landline will be charged at up to 3 pence per minute.

A call set-up fee of up to 6 pence may apply.)

 IE 01450 2655

When contacting the after-sales service, please quote the appliance's product number (E no.) and production number (FD) (see the inside of the door). Set the programme selector to Off and remove the appliance plug from the socket.

The Start indicator light does

not come on.

Mains plug plugged in? Programme selected?

The ā symbol and Start

indicator light are flashing.

Empty the condensation container a page 4.

Check the condensation outlet hose, if applicable (kink).

The 4 symbol and Start

indicator light are flashing.

Clean the air cooler apage 6 Cleaning and care.

Clean the fluff filter apage 4.

The u symbol flashes. Is the water tank empty?

Filling with distilled water a page 9.

The filter in the water tank may have become dirty.

If so, clean the filter in the water tank a

page 4.

The Drying - Steam Refresh does not start.

Dryer does not start. Has the Start button been pressed? Is the door closed?

Programme set? Ambient temperature greater than 5 °C?

Water is leaking out. Make sure the dryer is level.

Clean the air cooler seal.

The door opens by itself. Push the door closed until you hear it click into place.

Items crease even though the

Drying - Steam Refresh

programme has been selected.

Laundry load exceeded? Remove articles of clothing immediately after the end of the

programme, hang up and pull into shape.

Drying result was not achieved (laundry too damp).

Hot laundry feels damper than it actually is. The selected programme does not suit the load. Use

another drying programme or, in addition, select the time

programme apage7.

Use fine adjustment for the drying result apage1/2.

Fine layer of limescale on the humidity sensors a Clean

the humidity sensors apage 9.

Programme cancellation, e.g. tank full, mains power supply failure, door open or maximum drying time reached.

Drying time too long. Clean the fluff filter under running

water a page 4.

Insufficient supply of air a ensure that air can circulate.

Air inlet possibly blocked a Clear inlet apage 8.

Ambient temperature higher than 35 °C a Ventilate the

room.

The humidity in the room increases significantly.

Make sure the room is sufficiently ventilated.

One or more programme status indicator lamps are flashing.

Clean the filter and air cooler apage 4/6.

Check the installation conditions apage 10.

Switch off, allow to cool, switch on again and restart the programme.

The interior light (depending on the model) does not work.

Unplug the appliance plug, fold back the cover cap on the inside above the door (using a Torx 20 screwdriver) and replace the bulb. Close the cover cap.

Safety instructions

Emergency

 Pull the appliance plug out of the socket immediately or disconnect the fuse.

ONLY use the dryer...

 In rooms inside the house.  For drying or unwrinkling/refreshing fabrics.

The dryer must NEVER...

 Be used for purposes other than those described above.  Be modified in terms of its technology or properties.

Hazards

 The dryer must not be used by children or persons who have not been

instructed in its use.  Do not leave children unsupervised near the dryer.  Keep pets away from the dryer.  Remove all objects from pockets,

and lighters in particular a

risk of explosion.

 Do not lean or sit on the door a

risk of tipping.

 Open the door carefully. Hot steam may escape. The clothes and drum may

be hot a

risk of burns.

Installation

 Secure loose leads or hoses, otherwise there is a risk of tripping.  Below 0 °C there is a possibility of frost damage.

Mains connection

 Connect the dryer according to specifications to an AC earthed socket,

otherwise it cannot be guaranteed that the appliance is completely safe.  The cable cross-section must be sufficient.

 Only use earth-leakage circuit breakers with the following symbol:  The appliance plug and socket must be compatible.  Do not use multiple plugs/connectors and/or extension cables.  Do not touch or hold the appliance plug with wet hands

risk of electric shock.

 Never pull the appliance plug out of the socket by its cable.

 Do not damage the mains lead a risk of electric shock.

Operation

 Only laundry must be loaded into the drum.

Before switching on the dryer - check the contents.  Do not use the dryer if the laundry has been in contact with solvents, oil, wax,

grease or paint (e.g. hair setting spray, nail polish remover, stain remover,

cleaning solvent, etc.) a

fire/explosion hazard.

 Hazard caused by dust (e.g. coal dust, flour): do not use the dryer

risk of explosion.

 Do not put laundry containing foamed material/rubber in the dryer a elastic

material may be destroyed and the dryer may be damaged due to possible

deformation of the foamed material.  Switch off the dryer once the programme has ended.  For unwrinkling/refreshing fabrics, use distilled water only. Do not use

condensation, tap water or additives.  Distilled/condensation water is not for drinking.

Defect

 Do not use the dryer if it is defective or if you suspect that it is.

Repairs must only be carried out by the after-sales service.  Do not use a dryer with a faulty mains lead. To prevent risks, a faulty mains

lead must only be replaced by the after-sales service.  Before changing the bulb of the interior light make absolutely sure you have

pulled the appliance plug from the socket a

risk of electric shock.

Spare parts

 Only use genuine spare parts and accessories for safety reasons.

Disposal

 Dryer: unplug the appliance plug, then cut the mains lead from the appliance.

Dispose of the dryer at an approved public disposal facility.  Packaging: keep all packaging out of reach of babies and children.

a danger of suffocation.

 All materials are environmentally safe and recyclable. Dispose of in an

environmentally-responsible manner.

Operating and installation instructions

Observe the safety instructions on page 13.

Read these instructions before switching on the dryer.

Caution - risk of scalding.

Tumble dryer

1 2

ˎ,ü@°CA

Low Heat

Reduced temperature for delicate fabrics time; e.g. acrylic, polyamide, elastane or a

ˎ@ Easy Iron Reduces creasing and prolongs the anti-cre

programme has finished; can be selected

Status indicators

Icc+cc\

Indicators which show the programme seq Drying, Iron Dry, Cupboard Dry, End / Eas

Service indicators

4 clean

. container

u water tank

Clean the fluff filter and/or air cooler apa

Empty the condensation container.

Fill the water tank with distilled water ap

For selecting the settings.

ˎMenu

For changing all the settings in the display panel.

ˎChange 

1 -24 hrs End of the programme after ... (depending on the programme selected, e.g. 1:54h a 2h;

you can always select up to the next full hour).

Electronic start timer



0, 1, 2, 3, 4 There are four buzzer volume settings: 0 (off), 1 (quiet), 2 (normal), 3 (loud), 4 (very loud). Signal

On-Off Provides protection against unintentional changes to the functions set

(press and hold the

Menu button for 5 seconds).

Appliance lock

(depending on the model)

0, 1, 2, 3

The drying result (e.g. cupboard dry) can be increased in three stages (1 - 3) for the programmes

Ê Cottons, Easy-Care and Rapid 40 a presetting = 0.

After one of these programmes has been finely adjusted, the setting is retained for the others.

Fine adjustment Drying result

600-1800 ²The spin speed that was used in the washing machine;

for more precise indication of the projected drying duration only.

Spin speed



... and adapt to individu

Never operate the dryer if it is damaged. Inform your after-sales service.

Sorting and load

Remove all objects from pockets. Pay particular attention to cigarette lighters. The drum must be empty before filling.

If necessary, fill the water tank for Steam Refresh/Drying programmes

a page 8.

See programme overview on page 7. See also separate instructions for basket for wo

(depending on the model)

Your new dryer

Congratulations! - You have chosen a modern, high-quality domestic appliance from Siemens.

Environmentally-responsible disposal

Dispose of packaging in an environmentally-responsible manner. This appliance is designated according to European directive



2002/96/EC which governs waste electrical and electronic equipment (WEEE).

This directive provides the framework for the EU-wide collection and reuse of used appliances.

For further information about our products, accessories, spare parts and services, please visit: www.siemens-home.com

Intended use

Contents Page

ʋPreparation . . . . . . . . . . . . . . . . . . . . . . 2

ʋSetting the programmes . . . . . . . . . . . . . 2

ʋDrying . . . . . . . . . . . . . . . . . . . . . . . . 3/4

ʋNotes on laundry . . . . . . . . . . . . . . . . . . 5

ʋCleaning and care . . . . . . . . . . . . . . . . . . 6

ʋOverview of programmes . . . . . . . . . . . . 7

ʋShort spin / Refresh . . . . . . . . . . . . . . 8/9

ʋInstallation . . . . . . . . . . . . . . . . . . . . . . 10

ʋFrost protection / Transport. . . . . . . . . . 10

ʋTechnical data . . . . . . . . . . . . . . . . . . . 11

ʋOptional accessories . . . . . . . . . . . . . . .11

ʋWhat to do if... / After-sales service . . . .12

ʋSafety instructions . . . . . . . . . . . . . . . . 13

Preparing for installation, see page 8

Selecting and adjusting the

Additional functions

Select the dry

Press th 

Only if your hands are dry. Only hold the plug by the plug casing.

Conne

Display panelProgramme selector

All buttons a a light touch

Display for max. load capacity for selected programme

ʋonly for domestic use.

ʋonly to be used for drying, refreshing or unwrinkling

fabrics that have been washed with water.

Do not leave children unsupervised near the dryer. Keep pets away from the dryer.

+ 7 hidden pages