Siemens SITOP UPS1600 under STEP 7 V12 Getting Started
SITOP UPS1600 under STEP 7 V12
___________________
___________________
___________________
___________________
___________________
SITOP UPS1600 under STEP 7
V12
Getting Started
Introduction
1
Safety notes
2
Description
3
Assigning the IP address
4
Installing and configuring the
SITOP UPS1600 in STEP 7
V12
5
Parameterizing the SITOP
UPS1600
6
Siemens AG
Industry
Postfach 48 48
90026 NÜRNBERG
GERMANY
Ⓟ
Copyright © Siemens AG .
All rights reserved
Warning notice system
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
Qualified Personnel
personnel qualified
Proper use of Siemens products
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
Disclaimer of Liability
Legal information
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
The product/system described in this documentation may be operated only by
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
for the specific
Note the following:
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Sector
02/2014 Technical data subject to change
Table of contents
1 Introduction................................................................................................................................... 5
2 Safety notes ................................................................................................................................. 7
3 Description ................................................................................................................................... 9
4 Assigning the IP address .............................................................................................................. 11
5 Installing and configuring the SITOP UPS1600 in STEP 7 V12 ......................................................... 17
6 Parameterizing the SITOP UPS1600 ............................................................................................. 25
1.1 Purpose of this document ......................................................................................................... 5
1.2 Technical support ..................................................................................................................... 5
1.3 Additional documentation ......................................................................................................... 6
3.1 System overview ...................................................................................................................... 9
6.1 Buffering an S7 IO controller, including the I/O when the power fails ....................................... 25
6.2 Switching off the UPS when the power fails by a user program ............................................... 29
SITOP UPS1600 under STEP 7 V12
Getting Started,
3
1
1.1
Purpose of this document
Basic knowledge required
Range of validity
1.2
Technical support
Technical support
Technical documentation on the Internet
SITOP power supply homepage
This Getting Started guides you through configuring the UPS1600 under STEP 7 V12 for the
following two tasks:
● Buffering the S7 IO controller, including the I/O when the power fails
● Switching off the UPS when the power fails by the user program
The following are required to understand the Getting Started:
● Knowledgeable about using personal computers with the Windows operating system
● Knowledgeable about how to configure an uninterruptible power supply using the
UPS1600, including the S7 IO controller and connected battery modules
● Creating and editing projects under STEP 7 V12 in the TIA-Portal.
Getting Started is valid for STEP 7 V12, Version 12.0 with service pack 1 (SP1).
Technical support for all IA/DT products can be accessed through the following
communication channels:
● Phone: + 49 (0) 911 895 7222
● E-Mail (mailto:support.automation@siemens.com
● Internet:
Online support request form (http://www.siemens.com/automation/support-request
Operating instructions and manuals for SITOP are available in the Internet:
Operating instructions/manuals (http://www.siemens.com/sitop/manuals
)
)
)
SITOP UPS1600 under STEP 7 V12
Getting Started,
General news about our power supplies is available in the Internet at the SITOP home page
(http://www.siemens.com/sitop
).
5
Introduction
1.3
Additional documentation
1.3 Additional documentation
Further information is available in the following documents:
● UPS1600 and UPS1100 manuals
● IO controller manual
● STEP 7 V12 manual
SITOP UPS1600 under STEP 7 V12
6 Getting Started,
2
WARNING
Correct handling of the devices
When operating electrical devices, it is inevitable that certain components will carry
dangerous voltages.
Therefore, failure to handle the units properly can result in death or serious physical injury
as well as extensive property damage.
Only appropriately qualified personnel may work on or in the vicinity of this equipment.
Perfect, safe, and reliable operation of this equipment is dependent on proper
transportation, storage, installation and mounting.
Before installation or maintenance work can begin, the system's main switch must be
switched off and measures taken to prevent it being switched on again.
If this instruction is not observed, touching live parts can result in death or serious injury.
The relevant DIN/VDE regulations or country-specific specifications (e.g. VDE 0510 Part 2 /
EN50272-2) must be observed for the storage, assembly and operation of the lead
accumulators. It must be ensured that the battery location is suitably ventilated. Potential
ignition sources must be separated by at least 50 cm.
SITOP UPS1600 under STEP 7 V12
Getting Started,
7
3
3.1
System overview
Application
Device integration
Languages
The principal tasks that you can perform with the SITOP UPS Management:
● Connecting the uninterruptible SITOP UPS1600 power supply to the IO controller S7
● Configuring the SITOP UPS1600 uninterruptible power supply
● Protecting a computer or a computer network using the uninterruptible power supply
● Defining the battery maintenance intervals
SITOP UPS Management supports the following devices:
● UPS1600
● UPS1100
UPS1600 can be used with STEP 7 V12 as of version 12.0 with Servicepack 1 (SP1).
After the UPS1600 has been saved in the hardware catalog of STEP 7 V12 by installing the
hardware support package, it can be integrated into projects, parameterized and diagnosed.
German, English
French, Italian, Spanish and Chinese being prepared.
SITOP UPS1600 under STEP 7 V12
Getting Started,
9
4
General information
Note
Additional information
Additional information is contained in the Primary Setup Tool manual. This manual and
further links can be found under
(
Preconditions
Just like all devices connected to PROFINET, SITOP UPS1600 requires an IP address. This
is defined by the person responsible for the system. In this Getting Started, the configuration
of the SITOP UPS1600 interface is described using the Primary Setup Tool.
The Primary Setup Tool is a Siemens product that is free of charge and which is used to
identify and configure network-conform devices. You can download the Primary Setup Tool
under (http://support.automation.siemens.com/WW/view/en/19440762
).
http://support.automation.siemens.com/WW/view/en/19440762).
● The SITOP UPS1600 is connected with the client (PG/PC) via the Ethernet interface.
● The Primary Setup Tool is installed on the client.
SITOP UPS1600 under STEP 7 V12
Getting Started,
11
Assigning the IP address
Procedure
1. Called the Primary Setup Tool.
2. In the Primary Setup Tool select the menu command "Settings > Set PG/PC Interface...".
SITOP UPS1600 under STEP 7 V12
12 Getting Started,
Loading...