Siemens SIMATIC NET SCALANCE X-300M, SCALANCE X308-2M, SCALANCE X308-2M TS Compact Operating Instructions

SCALANCE X-300M

___________________

SIMATIC NET

Industrial Ethernet switches SCALANCE X-300M

Compact Operating Instructions

10/2014

A5E02630801

-06

Introduction

Safety notes

Description

Assembling

Connecting

Technical data

Dimension drawings

Approvals

Siemens AG Industry Sector Postfach 48 48 90026 NÜRNBERG GERMANY

A5E02630801-06

Ⓟ

10/2014 Subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified personnel are those who, based on their training and experience, are capable of identifying risks and avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions.

SCALANCE X-300M Compact Operating Instructions, 10/2014, A5E02630801-06

Table of contents

1 Introduction ............................................................................................................................................. 5

1.1 Introduction to the X-300M ....................................................................................................... 5

1.2 Product group X-300M .............................................................................................................. 7

1.3 Type designation ....................................................................................................................... 8

2 Safety notes ............................................................................................................................................ 9

2.1 Important notes on using the SCALANCE X-300 product family ............................................. 9

2.2 Important notes on using the device in hazardous areas ....................................................... 11

3 Description ............................................................................................................................................ 13

3.1 Unpacking and checking ......................................................................................................... 13

3.2 X-300M components of the product ........................................................................................ 13

3.3 Product group X-300M ............................................................................................................ 14

3.3.1 SCALANCE X308-2M and X308-2M TS................................................................................. 14

3.4 The SET / SELECT button ...................................................................................................... 16

3.5 LED display ............................................................................................................................. 17

3.6 Area of application and function of the C-PLUG ..................................................................... 21

3.7 Removing and inserting the C-PLUG (compact housing)....................................................... 22

4 Assembling ........................................................................................................................................... 23

4.1 Installation ............................................................................................................................... 23

4.2 Installation options .................................................................................................................. 24

4.3 General installation ................................................................................................................. 25

4.3.1 Installation on a DIN rail .......................................................................................................... 25

4.3.2 Installation on a standard rail .................................................................................................. 27

4.3.3 Wall mounting ......................................................................................................................... 28

4.4 Installation of modular devices ............................................................................................... 29

4.4.1 Installation and removal of media modules ............................................................................ 29

4.4.2 SFP installation in SFP media module ................................................................................... 33

5 Connecting ........................................................................................................................................... 35

5.1 Notes on commissioning ......................................................................................................... 35

5.2 Connecting functional ground ................................................................................................. 36

5.3 Signaling contact ..................................................................................................................... 36

5.3.1 Connecting the signaling contact ............................................................................................ 37

Table of contents

SCALANCE X-300M

4 Compact Operating Instructions, 10/2014, A5E02630801-06

5.4 Power supply .......................................................................................................................... 38

5.4.1 Power supply - general .......................................................................................................... 38

5.4.2 12 / 24 VDC - product group X-300M .................................................................................... 38

5.4.3 Connecting the power supply ................................................................................................. 39

6 Technical data ...................................................................................................................................... 41

6.1 Construction, installation and environmental conditions ........................................................ 41

6.2 Connectors and electrical data .............................................................................................. 43

6.3 Cable lengths ......................................................................................................................... 45

6.4 Other properties ..................................................................................................................... 46

7 Dimension drawings .............................................................................................................................. 49

7.1 X-300M dimension drawings .................................................................................................. 49

8 Approvals ............................................................................................................................................. 51

8.1 X-300M approvals, certificates ............................................................................................... 51

8.2 Declaration of conformity ....................................................................................................... 55

8.3 X-300M FDA and IEC approvals............................................................................................ 55

8.4 Overview of X-300M approvals .............................................................................................. 56

8.5 X-300M mechanical stability (in operation) ............................................................................ 56

Index .................................................................................................................................................... 57

SCALANCE X-300M Compact Operating Instructions, 10/2014, A5E02630801-06

1.1

Introduction to the X-300M

Purpose of the Operating Instructions (compact)

These operating instructions (compact) contain information with which you will be able to install and connect up a device of the SCALANCE X-300 product line.

Validity of these Operating Instructions (compact)

These Operating Instructions (compact) are valid for the product group

X-300M

of the

SCALANCE X-300 product line (see product overview).

Names of the devices in these operating instructions (compact)

Classification

Description

Terms used

Product line For all devices and variants of all product groups within the SCALANCE

X-300 product line, the term

IE switches X-300

is used.

IE switches X-300

Product group

For all devices and variants of a product group, only the product group is used.

X-300M Device

For a device, only the device name is used.

X308-2M

Variant For a variant of the device, the device name has the appropriate variant

added to it in brackets (2x24V).

(-)

All variants of a

device

For all variants of the device, the device name has (all) added to it. (-)

Where can I find more detailed information on the product?

A CD is supplied with the IE Switches X-300 on which you will find a detailed description of the products in PDF format in the relevant subfolder.

Introduction

1.1 Introduction to the X-300M

SCALANCE X-300M

6 Compact Operating Instructions, 10/2014, A5E02630801-06

Security messages

Note

Siemens offers IT security mechanisms for its automation and drive product portfolio in order to

support the safe operation of the plant/machine. Our products are also continuously

developed further with regard to IT security. We therefore recommend that you regularly check for updates of our products and that you only use the latest versions. You wil

l find

information in:

(

http://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo2&aktprim=99&lang=

)

Here, you can register for a pr

oduct-specific newsletter.

For the safe operation of a plant/machine, however, it is also necessary to integrate the automation components into an overall IT security concept for the entire plant/machine, which corresponds to the state

-of-the-art IT technology. You will find information on this in:

(http://www.siemens.com/industrialsecurity)

Products from other manufacturers that are being used must also be taken into account.

SIMATIC NET glossary

Explanations of many of the specialist terms used in this documentation can be found in the SIMATIC NET glossary.

You will find the SIMATIC NET glossary here:

● SIMATIC NET Manual Collection or product DVD

The DVD ships with certain SIMATIC NET products.

● On the Internet under the following entry ID:

50305045 (http://support.automation.siemens.com/WW/view/en/50305045

)

Introduction

1.2 Product group X-300M

SCALANCE X-300M Compact Operating Instructions, 10/2014, A5E02630801-06

1.2

Product group X-300M

Device

Properties

Order number

X308-2M

1 x 24 VDC

4 x 10/100/1000 Mbps, RJ-45 ports electrical 2 x 100/1000 Mbps for 2-port media modules LEDs, connector power supply and data cable outlet on

front

Diagnostics port at rear

6GK5 308-2GG00-2AA2

X308-2M TS

1 x 12 VDC, module varnished

4 x 10/100/1000 Mbps, RJ-45 ports electrical 2 x 100/1000 Mbps for 2-port media modules LEDs, connector power supply and data cable outlet on

front

Diagnostics port at rear

6GK5 308-2GG00-2CA2

Introduction

1.3 Type designation

SCALANCE X-300M

8 Compact Operating Instructions, 10/2014, A5E02630801-06

1.3

Type designation

Structure of the type designation

The type designation of an IE Switch X-300 is made up of several parts that have the following meaning:

Interfaces of devices without optical ports:

Interface

Property

Electrical RJ-45 port for 10/100 Mbps.

[-]

Electrical RJ-45 port for 10/100 Mbps or 10/100/1000 Mbps.

Interfaces of devices with optical ports:

Interface

Property

SC port 100 Mbps multimode FO cable (up to max. 5 km).

LD FE

SC port 100 Mbps single mode FO cable (up to max. 26 km).

[-]

SC port 1000 Mbps multimode FO cable (up to max. 750 m).

SC port 1000 Mbps single mode FO cable (up to max. 10 km).

SC port 1000 Mbps single mode FO cable (up to max. 40 km).

LH+

SC port 1000 Mbps single mode FO cable (up to max. 70 km).

If information applies to all devices, the term "IE Switches X-300" is used. If information applies to only a particular product group, the relevant names will be used without extra information on the type or number of interfaces. Examples: "X-300" stands for non-modular devices with a compact housing, "XR-300" means all rack devices, "X-300M" means all modular devices etc.

SCALANCE X-300M Compact Operating Instructions, 10/2014, A5E02630801-06

2.1

Important notes on using the SCALANCE X-300 product family

Safety notices on the use of the device

The following safety notices must be adhered to when setting up and operating the device and during all associated work such as installation, connecting up, replacing or opening the device.

General information

WARNING

Safety extra low voltage

The equipment is designed for operation with Safety Extra-Low Voltage (SELV) by a Limited Power Source (LPS). (This does not apply to 100 V...240 V devices.)

This means that only SELV / LPS (Limited Power Source) complying with IEC 60950-1 / EN 60950-1 / VDE 0805-1 must be connected to the power supply terminals. The power supply unit for the equipment power supply must comply with NEC Class 2, as described by the National Electrical Code (r) (ANSI / NFPA 70).

There is an additional requirement if devices are operated with a redundant power supply:

If the equipment is connected to a redundant power supply (two separate power supplies), both must meet these requirements.

WARNING

Opening the device

DO NOT OPEN WHEN ENERGIZED.

Safety notes

2.1 Important notes on using the SCALANCE X-300 product family

SCALANCE X-300M

10 Compact Operating Instructions, 10/2014, A5E02630801-06

General notices about use in hazardous areas

WARNING

Risk of explosion when connecting or disconnecting the device

EXPLOSION HAZARD

DO NOT CONNECT OR DISCONNECT EQUIPMENT WHEN A FLAMMABLE OR COMBUSTIBLE ATMOSPHERE IS PRESENT.

WARNING

Replacing components

EXPLOSION HAZARD

SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I, DIVISION 2 OR ZONE 2.

WARNING

Requirements for the cabinet/enclosure

When used in hazardous environments corresponding to Class I, Division 2 or Class I, Zone 2, the device must be installed in a cabinet or a suitable enclosure.

Safety notices on use in hazardous areas according to ATEX and IECEx

WARNING

Requirements for the cabinet/enclosure

To comply with EC Directive 94/9 (ATEX95) or the conditions of IECEx, this enclosure must meet the requirements of at least IP54 in compliance with EN 60529.

WARNING

Suitable cables for temperatures in excess of 70 °C

If the cable or conduit entry point exceeds 70 °C or the branching point of conductors exceeds 80 °C, special precautions must be taken. If the equipment is operated in an air ambient in excess of 50 °C - 70 °C, only use cables with admitted maximum operating temperature of at least 80 °C.

Safety notes

2.2 Important notes on using the device in hazardous areas

SCALANCE X-300M Compact Operating Instructions, 10/2014, A5E02630801-06

WARNING

Protection against transient voltage surges

Provisions shall be made to prevent the rated voltage from being exceeded by transient voltage surges of more than 40%. This criterion is fulfilled, if supplies are derived from SELV (Safety Extra-Low Voltage) only.

2.2

Important notes on using the device in hazardous areas

WARNING

WARNING - EXPLOSION HAZARD -

DO NOT DISCONNECT WHILE CIRCUIT IS LIVE UNLESS AREA IS KNOWN TO BE NON-HAZARDOUS.

WARNING

Restricted area of application

This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D or nonhazardous locations only.

WARNING

Restricted area of application

This equipment is suitable for use in Class I, Zone 2, Group IIC or non-hazardous locations only.

Safety notes

2.2 Important notes on using the device in hazardous areas

SCALANCE X-300M

12 Compact Operating Instructions, 10/2014, A5E02630801-06

SCALANCE X-300M Compact Operating Instructions, 10/2014, A5E02630801-06

3.1

Unpacking and checking

Unpacking, checking

WARNING

Do not use any parts that show evidence of damage

If you use damaged parts, there is no guarantee that the device will function according to the specification.

If you use damaged parts, this can lead to the following problems:

• Injury to persons

• Loss of the approvals

• Violation of the EMC regulations

Use only undamaged parts.

1. Make sure that the package is complete.

2. Check all the parts for transport damage.

3.2

X-300M components of the product

Note

When shipped, all devices have a C

-PLUG exchangeable medium.

Note

When shipped, the slots for the media modules have a dummy cover fitted.

Note

Labels to identify the installed MM900 media

modules are supplied with the modular devices

(M).

Table 3- 1 Overview of the components shipped with the

X-300M

product group

Device: SCALANCE

Variant

Plug-in terminal block

Device

BAK

Product CD

Signaling contact

Power supply X308-2M

(-)

2-pin

4-pin (24 V)

● ● ●

X308-2M TS

(-)

2-pin

4-pin (12 V)

● ● ●

Description

3.3 Product group X-300M

SCALANCE X-300M

14 Compact Operating Instructions, 10/2014, A5E02630801-06

3.3

Product group X-300M

3.3.1

SCALANCE X308-2M and X308-2M TS

Possible attachments

The SCALANCE X308-2M and X308-2M TS are partly modular devices and each has 8 ports.

●

4 fixed ports in the base device: 4 electrical RJ-45 jacks (with securing collars) for connection of end devices or other network segments.

●

4 modular ports via module slots: Two media modules (optical or electrical as required) can be combined using slots (S1S2) depending on the application. End devices and other network segments are connected according to the media modules being used.

Note

When shipped, the slots for the media modules have a dummy co

ver fitted.

Figure 3-1 SCALANCE X308-2M with dummy covers

Description

3.3 Product group X-300M

SCALANCE X-300M Compact Operating Instructions, 10/2014, A5E02630801-06

Possible attachments (example)

CAUTION

Use only approved media modules in the module slots

The connection of end devices or other network segments does not depend on the module slot, but rather on the selected media module.

Refer to the section Media module installation in slot.

Example of connections

Figure 3-2 SCALANCE X308-2M with MM992-2 and MM991-2

Column

1 2 3

Slot number

- - S1

Media modules used

MM992-2 MM991-2

Port number

P5 P7

- P3 P6 P8

Connection type

- Optical:

Gigabit Ethernet

Connection type depending on module used

Description

3.4 The SET / SELECT button

SCALANCE X-300M

16 Compact Operating Instructions, 10/2014, A5E02630801-06

3.4

The SET / SELECT button

The SET/SELECT button is located on the top of the housing of devices of the X-300 EEC series. On all other devices, this button is on the front panel of the housing beside the LED display. The SET/SELECT button has several functions that are described below.

Change the display mode

By pressing the button briefly, you change to the display mode of the LED display. For more detailed information on this topic, refer to the section "LED display".

Resetting the device to the factory defaults

If you reset, all the changes you have made will be overwritten by factory defaults. Follow the steps outlined below:

1. Turn on display mode A. Display mode A is active when the "DM" LED is not lit. If this LED is lit or flashing, you will need to press the SET/SELECT briefly (possibly several times) until the "DM" LED goes off. If the SELECT/SET button is not pressed for longer than a minute, the device also turns on display mode A.

2. Hold down the SELECT/SET button for 12 seconds. If you release the button before the 12 seconds have elapsed, the reset is canceled.

Definition of the fault mask

Using the fault mask, you specify an individual "good status" for the connected ports and the power supply. Deviations from this status are then displayed as errors/faults.

1. Turn on display mode A or D. Display mode A is active when the "DM" LED is not lit. Display mode D is active when the "DM" LED flashes yellow/orange. If a different display mode is active, you will need to press the SET/SELECT briefly (possibly several times) until the required display mode is active.

2. Hold down the SET/SELECT button for five seconds. After three seconds, the "DM" LED begins to flash. If you release the button before the five seconds have elapsed, the previous fault mask will be retained.

Enable/disable the redundancy manager

1. Turn on display mode B. Display mode B is active when the "DM" LED is lit green. If a different display mode is active, you will need to press the SET/SELECT briefly (possibly several times) until display mode B is active.

2. Hold down the SET/SELECT button for five seconds. After three seconds, the "DM" LED begins to flash. If you release the button before the five seconds have elapsed, the action is aborted.

3. The result of the action depends on the initial situation:

– If the redundancy manager and media redundancy were disabled, media redundancy

is also enabled after enabling the redundancy manager.

– If you disable the redundancy manager, media redundancy remains enabled.

Description

3.5 LED display

SCALANCE X-300M Compact Operating Instructions, 10/2014, A5E02630801-06

3.5

LED display

The "RM" LED for the "redundancy manager" function

The "RM" LED indicates whether or not the device is operating in the role of redundancy manager and whether or not the ring is operating error-free.

LED color

LED status

Meaning

off

The device is not operating in the role of "redundancy manager".

green on The device is operating in the role of redundancy manager. The

ring is working without problems, monitoring is activated.

green flashes The device is operating in the role of redundancy manager. An

interruption has been detected on the ring and the device has

switched through.

The "SB" LED for the standby function

This LED shows the status of the standby function.

LED color

LED status

Meaning

off

The standby function is disabled.

green

The standby function is enabled. The standby section is passive.

green

flashes

The standby function is enabled. The standby section is active.

The "F" LED for the fault status

The "F" LED (fault) provides information on the error/fault status of the device. While the device is starting up, this LED has the following meaning:

LED color

LED status

Meaning during the device startup

off

Device startup completed successfully.

red

Device startup not yet completed or a fault/error has occurred.

red

flashes

Bad firmware image.

During normal operation, the "F" LED provides the following information:

LED color

LED status

Meaning during operation

off

No operating problems.

red

The device has detected an error. The signaling contact opens.

Description

3.5 LED display

SCALANCE X-300M

18 Compact Operating Instructions, 10/2014, A5E02630801-06

The "DM" LED for the display mode

The "DM" LED (Display Mode) indicates which of the four display modes A, B, C or D is currently active. The meaning of the L1, L2 and P1, P2, ... LEDs depends on the display mode.

LED color

LED status

Meaning

off

Display mode A

green

Display mode B

orange

Display mode C

yellow/orange flashes Display mode D

Selecting the display mode

Press the SELECT/SET button to set the required display mode. If the SELECT/SET button is not pressed for longer than a minute, the device automatically changes to display mode A.

Pressing the SELECT/SET button starting at display mode A

Status of the "DM" LED

Display mode

off

Display mode A (default mode)

Press once

lit green

Display mode B

Press twice

lit orange

Display mode C

Press 3 times

flashes yellow/orange

Display mode D

The "L1" and "L2" or "L" LEDs for the power supply

Whereas on other devices, the "L1" and "L2" LEDs indicate information about the power, on the SCALANCE X306-1LD FE, this is done by the "L" LED. A redundant power supply for this device can be recognized by the color of the LED.

Meaning in display mode A, B or C

LED

Color

Status

Meaning

X308-2M (24 VDC)

X308-2M TS (12 VDC)

L1 / L2 - off Power supply L1 / L2 lower

than 17 V *

)

Power supply L1 / L2 less than 12 V,

device switched off

green on Power supply L1 / L2 higher

than 17 V *)

Power supply L1 / L2 higher

than 12 V

off

Power supplies L1 and L2 less than 17 V or not connected.

orange on Power supply L1 or L2 higher than 17 V

(no redundant supply).

green on Power supplies L1 and L2 higher than 17 V

(redundant supply).

*) Limit voltage = 17 VDC

+ 40 hidden pages

Siemens SIMATIC NET SCALANCE X-300M, SCALANCE X308-2M, SCALANCE X308-2M TS Compact Operating Instructions

Specifications and Main Features

Frequently Asked Questions

User Manual