Siemens SIMATIC NETS7-1200 Operating Instructions Manual
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
CP 1242-7
SIMATIC NET
S7-1200 - Telecontrol
CP 1242-7
Operating Instructions
_________________
Preface
_________________
Application and properties
_________________
Displays and connectors
Installing, connecting up and
_________________
commissioning
_________________
Notes on operation
_________________
Configuration
_________________
Technical specifications
_________________
Dimension drawings
_________________
Approvals
_________________
Accessories
_________________
References
_________________
Training, Service & Support
1
2
3
4
5
6
A
B
C
D
E
09/2011
C79000-G8976-C247-02
Legal information
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.
CAUTION
without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.
NOTICE
indicates that an unintended result or situation can occur if the relevant information is not taken into account.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Industry Sector
Postfach 48 48
90026 NÜRNBERG
GERMANY
Order number: C79000-G8976-C247
Ⓟ 10/2011
Copyright © Siemens AG 2011.
Technical data subject to change
Preface
Validity of this manual
This document contains information on the following product:
CP 1242-7
Order number 6GK7 242-7KX30-0XE0
Hardware product version 1, firmware version V1.0
The device is the communications processor for data transmission using GPRS for the
SIMATIC S7-1200.
Figure 1 CP 1242-7
At the top right behind the hinged cover of the module housing, you will see the hardware
product version printed as a placeholder "X" (for example X 2 3 4). In this case, "X" would be
the placeholder for hardware product version 1.
Product name
In this document, the term "CP" is also used instead of the full product name "CP 1242-7".
CP 1242-7
Operating Instructions, 09/2011, C79000-G8976-C247-02
3
Loading...