Siemens SIMATIC IPC277D Operating Instructions Manual

___________________

SIMATIC

Industrial PC SIMATIC IPC277D

Operating Instructions

12/2016

A5E03409486

Preface

Overview

Safety instructions

Installing and connecting the device

Commissioning the device

Advanced device functions

Operating the device

Device expansion and parameter assignment

Device maintenance and repairs

Technical specifications

Technical Support

Markings and symbols

List of abbreviations

-AE

Siemens AG Division Digital Factory Postfach 48 48 90026 NÜRNBERG GERMANY

A5E03409486-AE

Ⓟ

Legal information

Warning notice system

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

Qualified Personnel

personnel qualified

Proper use of Siemens products

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

Disclaimer of Liability

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage.

The product/system described in this documentation may be operated only by task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified personnel are those who, based on their training and experience, are capable of identifying risks and avoiding potential hazards when working with these products/systems.

Note the following:

for the specific

documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems. The permissible

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

We have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions.

12/2016 Subject to change

Preface

Basic knowledge required

Scope of validity of this documentation

Scope of this documentation

Conventions

These operating instructions contain all the information you need for commissioning and operation of the SIMATIC IPC277D.

It is intended both for programming and testing personnel who commission the device and connect it with other units (automation systems, programming devices), as well as for service and maintenance personnel who install add-ons or carry out fault/error analyses.

A solid background in personal computers and Microsoft operating systems is required to understand this manual. General knowledge in the field automation control engineering is recommended.

These operating instructions are valid for all versions of the SIMATIC IPC277D.

The documentation for the SIMATIC IPC277D consists of:

● Product information, e.g. "Important notes on your device"

● Quick Install Guide SIMATIC IPC277D

● SIMATIC IPC277D operating instructions in English and German

The PDF version of the documentation is supplied with the device on the "Documentation and Drivers" CD/DVD.

The terms "PC" or "device" are used in place of the product name SIMATIC IPC277D in these operating instructions.

In these operating instructions, the terms "Windows Embedded Standard 2009" and "Windows Embedded Standard 7" are also abbreviated with the term "Windows Embedded Standard". "Windows 7" is used as an abbreviation for "Windows 7 Ultimate".

SIMATIC IPC277D Operating Instructions, 12/2016, A5E03409486-AE

Preface

History

Edition

Comment

07/2011

First edition, valid for the first delivery stage

02/2012

Third edition with corrections

06/2013

Fourth edition with corrections

12/2016

Fifth edition with corrections

Guideline to the operating instructions

Content structure

Contents

and chapters

device

tions

device

The following earlier release versions of these operating instructions have been published:

11/2011 Second edition, valid for all delivery stages

Preface Purpose, layout and description of the important topics Table of contents Detailed organization of the documentation, including the index of pages

Overview

Safety instructions All generally valid safety aspects:

Installing and connecting the device

Commissioning the

Extended device func-

• Description of the product: Characteristics and field of application

• Product package

• Structure of the product/system: Operator control and connection ele-

ments

• Accessories

• Legal requirements

• Product/system view during installation

• General information on commissioning

• Notes on operation

• Application planning: Aspects of storage, transport, environmental and

EMC conditions to be considered in the preparatory stage.

• Installation: Product installation options and installation instructions

• Connection: Options of connecting the product and wiring instructions

• Integration: Options of integrating the product into existing or planned

automation systems and networks.

Commissioning the product/system

Monitoring and display functions

Expanding and assigning parameters to the

SIMATIC IPC277D

4 Operating Instructions, 12/2016, A5E03409486-AE

Procedure for installing device expansions (modules, drives)

Preface

Content structure

Contents

Abbreviations

Abbreviations of the technical terms used

Device maintenance and repair

Technical specifications

Technical support

• Replacing hardware components

• Restoring and setting up the operating system and BIOS (Recovery)

• Installing drivers and software

• Service and spare parts

• Recycling and disposal

• General specifications in compliance with relevant standards and cur-

rent/voltage values

• Guidelines and certifications, ESD guidelines, notes on retrofitting

• Dimension drawings: Dimensions of the device and of modules

• Detailed descriptions of boards and system resources

• Service and support

• Troubleshooting: Problems, causes, remedy

• BIOS Setup

SIMATIC IPC277D Operating Instructions, 12/2016, A5E03409486-AE

Preface

SIMATIC IPC277D

6 Operating Instructions, 12/2016, A5E03409486-AE

Preface ...................................................................................................................................................... 3

1 Overview .................................................................................................................................................. 11

2 Safety instructions ................................................................................................................................... 23

3 Installing and connecting the device ........................................................................................................ 29

4 Commissioning the device ....................................................................................................................... 53

1.1 Product description ................................................................................................................. 11

1.2 Configuration of the devices ................................................................................................... 13

1.2.1 SIMATIC IPC277D 7" ............................................................................................................. 13

1.2.2 SIMATIC IPC277D 9" ............................................................................................................. 15

1.2.3 SIMATIC IPC277D 12", 15" and 19" ....................................................................................... 17

1.2.4 IPC277D 7" and 9" – interfaces and operator controls ........................................................... 20

1.2.5 IPC277D 12", 15" and 19" – interfaces and operator controls ................................................ 20

1.3 Accessories ............................................................................................................................. 21

2.1 General safety instructions ..................................................................................................... 23

2.2 Notes on usage ....................................................................................................................... 27

3.1 Preparing for installation ......................................................................................................... 29

3.1.1 Checking the delivery package ............................................................................................... 29

3.1.2 Identification data of the device .............................................................................................. 31

3.1.3 Permitted mounting positions ................................................................................................. 33

3.1.4 Preparing the mounting cutout ................................................................................................ 35

3.2 Installing the device ................................................................................................................ 37

3.2.1 Installation guidelines ............................................................................................................. 37

3.2.2 Securing with clamps .............................................................................................................. 39

3.2.3 Securing with clamps (can be ordered as options) ................................................................. 41

3.3 Connecting the device ............................................................................................................ 42

3.3.1 Notes on connecting ............................................................................................................... 42

3.3.2 Connecting the protective earth .............................................................................................. 44

3.3.3 Connecting the power supply to the 7" and 9" devices .......................................................... 45

3.3.4 Connecting the power supply to the 12", 15 and 19" devices ................................................ 47

3.3.5 Connect device to networks .................................................................................................... 49

3.3.6 Mounting the Ethernet connector strain relief ......................................................................... 50

3.3.7 Securing the cables ................................................................................................................ 51

4.1 General information on commissioning .................................................................................. 53

4.2 Initial commissioning ............................................................................................................... 54

4.3 Windows Security Center ....................................................................................................... 55

SIMATIC IPC277D Operating Instructions, 12/2016, A5E03409486-AE

Table of contents

5 Advanced device functions ...................................................................................................................... 57

6 Operating the device ................................................................................................................................ 65

7 Device expansion and parameter assignment ......................................................................................... 77

8 Device maintenance and repairs ............................................................................................................. 81

5.1 Monitoring functions ............................................................................................................... 57

5.1.1 Overview of the monitoring functions ..................................................................................... 57

5.1.2 Temperature monitoring/display ............................................................................................ 58

5.1.3 Watchdog (WD) ...................................................................................................................... 58

5.1.4 Battery monitoring .................................................................................................................. 59

5.2 Enhanced Write Filter ............................................................................................................ 60

5.3 File-Based Write Filter ........................................................................................................... 62

5.4 Buffer memory MRAM (option) .............................................................................................. 63

6.1 Overview ................................................................................................................................ 65

6.2 Operating the touch screen .................................................................................................... 66

6.3 Configuring the touch screen ................................................................................................. 67

6.3.1 Standard calibration ............................................................................................................... 67

6.3.2 Extended calibration .............................................................................................................. 69

6.3.3 Extended Touch touch functionality ....................................................................................... 70

6.4 Using the on-screen keyboard ............................................................................................... 71

6.5 Setting the display brightness ................................................................................................ 72

6.6 Command line call ................................................................................................................. 73

6.7 Setting the screen saver ........................................................................................................ 74

6.8 WinMove ................................................................................................................................ 76

7.1 Open the device. .................................................................................................................... 77

7.2 Inserting and removing CompactFlash cards ........................................................................ 79

8.1 Cleaning the Device Front ..................................................................................................... 81

8.2 Recycling and disposal .......................................................................................................... 82

8.3 Installing and removing hardware .......................................................................................... 82

8.3.1 Repair information .................................................................................................................. 82

8.3.2 Maintenance ........................................................................................................................... 84

8.3.3 Replacing the backup battery ................................................................................................ 85

8.3.4 Replacing drives of IPC277D 7" and 9" ................................................................................. 88

8.3.5 Replacing the drive of an IPC277D 12", 15" and 19" ............................................................ 90

8.4 Installing the software ............................................................................................................ 92

8.4.1 Reinstalling the operating system .......................................................................................... 92

8.4.1.1 General installation procedure ............................................................................................... 92

8.4.1.2 Restoring the factory state ..................................................................................................... 93

8.4.1.3 Installing Windows XP ........................................................................................................... 94

8.4.1.4 Installation of Windows 7 ....................................................................................................... 96

8.4.1.5 Setting up the language selection by means of the Multilanguage User Interface (MUI) .... 100

SIMATIC IPC277D

8 Operating Instructions, 12/2016, A5E03409486-AE

Table of contents

9 Technical specifications ......................................................................................................................... 109

8.4.2 Partitioning data media ......................................................................................................... 102

8.4.2.1 Partitions in Windows Embedded Standard 2009 and Windows Embedded Standard 7 .... 102

8.4.2.2 Partitions under Windows 7 Ultimate and Windows XP Professional .................................. 103

8.4.2.3 Adapting partitions in Windows 7 Ultimate and Windows Embedded Standard 7 ............... 103

8.4.2.4 Adapting partitions in Windows XP and Windows Embedded Standard 2009 ..................... 104

8.4.3 Drivers and software ............................................................................................................. 105

8.4.3.1 Driver installation for Windows Embedded Standard 7 and 2009 ........................................ 105

8.4.3.2 Installing drivers and software .............................................................................................. 105

8.4.4 Installing updates .................................................................................................................. 107

8.4.4.1 Updating the operating system ............................................................................................. 107

8.4.4.2 Installing or updating application programs and drivers ....................................................... 107

9.1 Certificates and approvals .................................................................................................... 109

9.2 Directives and declarations ................................................................................................... 112

9.2.1 Electromagnetic compatibility for industrial environments .................................................... 112

9.2.2 ESD guideline ....................................................................................................................... 112

9.3 Dimension drawings.............................................................................................................. 115

9.3.1 Dimensional drawing IPC277D, 7" display ........................................................................... 115

9.3.2 Dimensional drawing IPC277D, 9" display ........................................................................... 116

9.3.3 Dimensional drawing IPC277D, 12" display ......................................................................... 117

9.3.4 Dimensional drawing IPC277D, 15" display ......................................................................... 118

9.3.5 Dimensional drawing IPC277D, 19" display ......................................................................... 119

9.4 Technical specifications ........................................................................................................ 120

9.4.1 General technical specifications ........................................................................................... 120

9.4.2 Environmental conditions ...................................................................................................... 123

9.4.3 Shipbuilding .......................................................................................................................... 124

9.4.4 Power supply IPC277D, 7" and 9" displays .......................................................................... 124

9.4.4.1 Power requirements of additional components .................................................................... 124

9.4.4.2 Power consumption .............................................................................................................. 125

9.4.4.3 DC power supply ................................................................................................................... 125

9.4.5 Power supply IPC277D, 12", 15" and 19" display ................................................................ 126

9.4.5.1 Power requirements of additional components .................................................................... 126

9.4.5.2 Power consumption .............................................................................................................. 126

9.4.5.3 DC power supply ................................................................................................................... 127

9.5 Hardware description ............................................................................................................ 128

9.5.1 Technical features of the motherboard ................................................................................. 128

9.5.2 External interfaces ................................................................................................................ 128

9.5.2.1 Overview of interfaces .......................................................................................................... 128

9.5.2.2 Serial interface ...................................................................................................................... 129

9.5.2.3 Ethernet port ......................................................................................................................... 129

9.5.2.4 USB 2.0 port ......................................................................................................................... 130

9.5.3 System resources ................................................................................................................. 131

9.5.3.1 Currently allocated system resources ................................................................................... 131

9.5.3.2 System resources used by the BIOS/DOS ........................................................................... 131

9.5.4 Input/output address areas ................................................................................................... 133

9.5.4.1 Overview of the internal module registers ............................................................................ 133

9.5.4.2 Battery status register (read-only) ........................................................................................ 133

9.5.4.3 MRAM address register ........................................................................................................ 133

SIMATIC IPC277D Operating Instructions, 12/2016, A5E03409486-AE

Table of contents

A Technical Support .................................................................................................................................. 161

B Markings and symbols ........................................................................................................................... 163

C List of abbreviations ............................................................................................................................... 167

Glossary ................................................................................................................................................ 171

Index ...................................................................................................................................................... 179

9.6 BIOS description .................................................................................................................. 134

9.6.1 Overview .............................................................................................................................. 134

9.6.2 Starting BIOS Setup ............................................................................................................. 134

9.6.3 BIOS Setup menus .............................................................................................................. 135

9.6.3.1 BIOS Setup overview ........................................................................................................... 135

9.6.3.2 Main menu ........................................................................................................................... 137

9.6.3.3 Advanced menu ................................................................................................................... 138

9.6.3.4 Security menu ...................................................................................................................... 143

9.6.3.5 Power menu ......................................................................................................................... 144

9.6.3.6 Boot menu ............................................................................................................................ 145

9.6.3.7 Version menu ....................................................................................................................... 151

9.6.3.8 Exit menu ............................................................................................................................. 152

9.6.4 BIOS Setup default settings ................................................................................................. 153

9.6.5 Alarm, error and system messages ..................................................................................... 156

9.7 Functional scope in Windows .............................................................................................. 157

9.7.1 Windows Embedded Standard 2009 ................................................................................... 157

9.7.2 Windows Embedded Standard 7 ......................................................................................... 159

A.1 Service and support ............................................................................................................. 161

A.2 Problem solving .................................................................................................................... 162

B.1 Overview .............................................................................................................................. 163

B.2 Safety ................................................................................................................................... 163

B.3 Operator controls ................................................................................................................. 163

B.4 Certificates, approvals and markings ................................................................................... 164

B.5 Interfaces ............................................................................................................................. 165

SIMATIC IPC277D

10 Operating Instructions, 12/2016, A5E03409486-AE

1.1

Product description

The SIMATIC IPC277D provides high-level industrial performance.

● Compact design

● Rugged

● Maintenance-free operation possible

SIMATIC IPC277D is available with various control units that differ with regard to the display size. This display is a color display with a backlit "wide-screen" format TFT color display.

Displays are available in the following sizes for the SIMATIC IPC277D:

● 7" touch

● 9" touch

● 12" touch

● 15" touch

● 19" touch

SIMATIC IPC277D Operating Instructions, 12/2016, A5E03409486-AE

Overview

Basic data

Conditions of use

Operation without fan

Monitoring and safety functions

Buffer memory

512 KB MRAM

1.1 Product description

Power supply 24V DC (19.2 to 28.8 V), max. 1.8 A

Watchdog

Voltage drop Up to 15 ms buffer time at full load

• Monitoring function for program execution

• Restart can be parameterized in the event of a fault

SIMATIC IPC277D

12 Operating Instructions, 12/2016, A5E03409486-AE

Overview

1.2

Configuration of the devices

1.2.1

SIMATIC IPC277D 7"

Front and side view

①

Display/touch screen

②

Mounting clamp recess

③

Mounting seal

Rear view

①

Rating plate

②

Interface designation

1.2 Configuration of the devices

SIMATIC IPC277D Operating Instructions, 12/2016, A5E03409486-AE

Overview

Bottom view

①

Interfaces and operating elements

②

Mounting clamp recess

③

Flap for memory card slot

1.2 Configuration of the devices

SIMATIC IPC277D

14 Operating Instructions, 12/2016, A5E03409486-AE

Overview

1.2.2

SIMATIC IPC277D 9"

Front and side view

①

Display/touch screen

②

Mounting clamp recess

③

Mounting seal

Rear view

①

Rating plate

②

Interface designation

1.2 Configuration of the devices

SIMATIC IPC277D Operating Instructions, 12/2016, A5E03409486-AE

Overview

Bottom view

①

Interfaces and operating elements

②

Mounting clamp recess

③

Flap for memory card slot

1.2 Configuration of the devices

SIMATIC IPC277D

16 Operating Instructions, 12/2016, A5E03409486-AE

1.2.3

SIMATIC IPC277D 12", 15" and 19"

Front and side view, 12"

①

Display/touch screen

②

Mounting clamp recess

③

Mounting seal

This section describes the 12", 15" and 19" devices using the example of the SIMATIC IPC277D 12". The 15" and 19" devices have an additional USB port at the front.

Overview

1.2 Configuration of the devices

SIMATIC IPC277D Operating Instructions, 12/2016, A5E03409486-AE

Overview

Front view, 15"

①

Front USB port

②

Display/touch screen

1.2 Configuration of the devices

The front view of the 19" device is similar.

SIMATIC IPC277D

18 Operating Instructions, 12/2016, A5E03409486-AE

Overview

Rear view

①

Rating plate

②

Interface designation

Bottom view

①

Mounting clamp recess

②

Interfaces and operating elements

③

Flap for memory card slot

1.2 Configuration of the devices

SIMATIC IPC277D Operating Instructions, 12/2016, A5E03409486-AE

Overview

1.2.4

IPC277D 7" and 9" – interfaces and operator controls

①

RJ45 Ethernet connection LAN2 for 10/100/1000 Mbps

②

RJ45 Ethernet connection LAN1 for 10/100/1000 Mbps

③

RS-232 interface, D-sub connector, 9-pin

④

Only two USB interfaces may be operated simultaneously in high-current mode.

⑤

On/off switch. OFF position, when the symbol "C-" is pressed in.

⑥

Connection for a 24 VDC power supply

⑦

Protective conductor connection

1.2.5

IPC277D 12", 15" and 19" – interfaces and operator controls

①

Protective conductor connection

②

On/off switch: OFF position, when the symbol "C-" is pressed in.

③

Connection for a 24 VDC power supply

④

RJ45 Ethernet connection LAN2 for 10/100/1000 Mbps

⑤

RJ45 Ethernet connection LAN1 for 10/100/1000 Mbps

⑥

RS-232 interface, D-sub connector, 9-pin

⑦

Only two USB interfaces may be operated simultaneously in high-current mode.

1.2 Configuration of the devices

USB 2.0 connection, high speed

Observe the printing on the rear of the device.

USB 2.0 connection, high speed

Observe the printing on the rear of the device.

SIMATIC IPC277D

20 Operating Instructions, 12/2016, A5E03409486-AE

Overview

1.3

Accessories

CompactFlash cards

Note Replace CompactFlash cards only with replacement cards of the same product versions

You may only operate this device with SIMATIC PC Co 03 (ES03 or higher).

Touch pen

1.3 Accessories

This section contains the scope of accessories valid at the time these operating instructions were written. Additional accessories can be found on the Internet at:

● Expansion components and accessories (http://www.automation.siemens.com/mcms/pc-

based-automation/en/industrial-pc/expansion_components_accessories)

● Industry Mall (http://mall.automation.siemens.com)

mpactFlash cards of product version

The following CompactFlash cards can be ordered:

● CompactFlash card, 2 GB

● CompactFlash card, 4 GB

● CompactFlash card, 8 GB

● CompactFlash card, 16 GB

The SIMATIC IPC touch pen is used for convenient operation of devices with touch screen.

SIMATIC IPC277D Operating Instructions, 12/2016, A5E03409486-AE

Overview

1.3 Accessories

SIMATIC IPC277D

22 Operating Instructions, 12/2016, A5E03409486-AE

2.1

General safety instructions

WARNING

Life-threatening voltages are present with an open control cabinet

System expansions

NOTICE

Damage through system expansions

WARNING

Risk of fire

When you install the device in a control cabinet, some areas or components in the open control cabinet may be carrying life-threatening voltages.

If you touch these areas or components, you may be killed by electric shock.

Switch off the power supply to the cabinet before opening it.

Device and system expansions may be faulty and can affect the entire machine or plant.

The installation of expansions can damage the device, machine or plant. Device and system expansions may violate safety rules and regulations regarding radio interference suppression. If you install or exchange system expansions and damage your device, the warranty becomes void.

Note the following for system expansions:

• Only install system expansion devices designed for this device. Contact your technical support team or where you purchased your PC to find out which system expansion devices may safely be installed.

• Observe the information on electromagnetic compatibility (Page 112).

The device is classified as "Open Type" for use in the area of industrial control equipment in accordance with UL508. Burning substances may escape and cause fire in the event of overheating.

Please therefore note the following:

• The installation of the device in an enclosure conforming to UL508 is a mandatory requirement for approval and operation in accordance with UL508.

• Install the device in an enclosure that meets the requirements of paragraphs 4.6 and

4.7.3 of the standards EN 60950-1:2006 and IEC/UL/EN/DIN-EN 60950-1.

SIMATIC IPC277D Operating Instructions, 12/2016, A5E03409486-AE

Safety instructions

Battery and rechargeable battery

WARNING

Risk of explosion and release of harmful substances

High frequency radiation

NOTICE

Unintentional operating situations

2.1 General safety instructions

Improper handling of lithium batteries can result in an explosion of the batteries.

Explosion of the batteries and the released pollutants can cause severe physical injury. Worn batteries jeopardize the function of the device.

Note the following when handling lithium batteries:

• Replace used batteries in good time; see the section "Replacing the backup battery" in the operating instructions.

• Replace the lithium battery only with an identical battery or types recommended by the manufacturer (order no.: A5E30314053).

• Do not throw lithium batteries into fire, do not solder on the cell body, do not recharge, do not open, do not short-circuit, do not reverse polarity, do not heat above 100°C, and protect from direct sunlight, moisture and condensation.

High frequency radiation, e g. from a cellular phone, interferes with device functions and can result in malfunctioning of the device.

Persons are injured and the plant is damaged.

Avoid high-frequency radiation:

• Remove radiation sources from the environment of the device.

• Switch off radiating devices.

• Reduce the radio output of radiating devices.

• Observe the information on electromagnetic compatibility (Page 112).

SIMATIC IPC277D

24 Operating Instructions, 12/2016, A5E03409486-AE

Safety instructions

ESD Guideline

NOTICE

Electrostatic sensitive devices (ESD)

through voltages

Industrial Security

Disclaimer for third-party software updates

2.1 General safety instructions

Electrostatic sensitive devices can be labeled with an appropriate symbol.

When you touch electrostatic sensitive components, you can destroy them that are far below the human perception threshold.

If you work with components that can be destroyed by electrostatic discharge, observe the ESD Guideline (Page 112).

Siemens provides products and solutions with industrial security functions that support the secure operation of plants, systems, machines and networks.

In order to protect plants, systems, machines and networks against cyber threats, it is necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial security concept. Siemens’ products and solutions only form one element of such a concept.

Customer is responsible to prevent unauthorized access to its plants, systems, machines and networks. Systems, machines and components should only be connected to the enterprise network or the internet if and to the extent necessary and with appropriate security measures (e.g. use of firewalls and network segmentation) in place.

Additionally, Siemens’ guidance on appropriate security measures should be taken into account. For more information about industrial security, please visit (http://www.siemens.com/industrialsecurity).

Siemens’ products and solutions undergo continuous development to make them more secure. Siemens strongly recommends to apply product updates as soon as available and to always use the latest product versions. Use of product versions that are no longer supported, and failure to apply latest updates may increase customer’s exposure to cyber threats.

To stay informed about product updates, subscribe to the Siemens Industrial Security RSS Feed under (http://www.siemens.de/automation/csi_en_WW).

This product includes third-party software. Siemens AG only provides a warranty for updates/patches of the third-party software, if these have been distributed as part of a Siemens software update service contract or officially released by Siemens AG. Otherwise, updates/patches are undertaken at your own risk. You can find more information about our Software Update Service offer on the Internet at Software Update Service (http://www.automation.siemens.com/mcms/automation-software/en/software-update-

service/Pages/Default.aspx).

SIMATIC IPC277D Operating Instructions, 12/2016, A5E03409486-AE

Safety instructions

Notes on protecting administrator accounts

2.1 General safety instructions

A user with administrator privileges has extensive access and manipulation options in the system.

Therefore, ensure there are adequate safeguards for protecting the administrator accounts to prevent unauthorized changes. To do this, use secure passwords and a standard user account for normal operation. Other measures, such as the use of security policies, should be applied as needed.

SIMATIC IPC277D

26 Operating Instructions, 12/2016, A5E03409486-AE

Safety instructions

2.2

Notes on usage

WARNING

Risks associated with the unprotected machine or plant

Environment

NOTICE

Ambient conditions and chemical resistance

Without additional safety measures, such as a supply of clean air, the device may not be

2.2 Notes on usage

According to the results of a risk analysis, certain hazard potentials associated with the unprotected machine exist. These hazards could lead to personal injury.

Avoid such hazards by taking the following precautions in accordance with the risk analysis:

• Installation of additional safety equipment on the machine or plant. In particular, the

programming, parameter assignment and wiring of the inserted I/O modules must be executed in accordance with the safety performance identified by the necessary risk analysis (SIL, PL or Cat.).

• Use as intended must be validated for the device by means of a function test on the

plant. These tests help you to identify programming, parameter assignment and wiring errors.

• Documentation of the test results that you can enter in the relevant safety verification

documents, if necessary.

Unsuitable environmental conditions have a negative impact on device operation. Chemical substances such as cleaners or fuels may alter the color, shape and structure of the device surface, for example, the front panel.

The device may be damaged. possibly resulting in malfunctions.

For this reason, please observe the following precautions:

• Always operate the device in closed rooms. All warranties shall be void in the case of

noncompliance.

• Operate the device only in accordance with the ambient conditions specified in the

technical specifications.

• Protect the device against dust, moisture and heat.

• Do not expose the device to direct sunlight or to other strong sources of light.

•

used in locations with harsh operating conditions caused by acidic vapors or gases.

• Always use suitable cleaning agents. Read the information on the Internet concerning

chemical resistance, see the "After Sales Information System for SIMATIC PC/PG" (http://www.siemens.com/asis) link in the chapter "Technical Support" in section service and support (Page 161).

SIMATIC IPC277D Operating Instructions, 12/2016, A5E03409486-AE

Safety instructions

Note Use in an industrial environment without additional protective measures

The device has been designed for use in a normal industrial environment in accordance with IEC

TFT displays

NOTICE

Burn-in effect and backlighting

eensaver. The backlight brightness is reduced while the screensaver is

Defective pixels in the display

2.2 Notes on usage

60721-3-3 (pollutant class 3C2 for chemical influences, 3S2 for sand and dust).

A permanent picture with bright screen objects leads to a burn-in effect. The longer the same screen contents are displayed, the longer it will take for the burn-in effect to disappear. Screensavers (for example, "starfield simulation") for the backlit active black mode reduce the burn-in effect. The brightness of the backlighting deteriorates over the course of the screen's life cycle.

The service life of the screen and backlighting is extended by the following measures:

• Switch on the scr active.

• You should also reduce the backlighting.

• Observe the backlighting operating time.

At present, the manufacturing process of modern displays does not guarantee that all pixels of the display will be perfect. A small number of defective pixels in the display is therefore unavoidable. This does not present a functional problem as long as the defective pixels are not bunched in one location.

Additional information is available in the section "General technical specifications (Page 120)".

SIMATIC IPC277D

28 Operating Instructions, 12/2016, A5E03409486-AE

3.1

Preparing for installation

3.1.1

Checking the delivery package

Procedure

Note Damage to the device during transport and storage

If a device is transported or stored without packaging, shocks, vibrations, pressure and moisture may impact the unprotected unit. A damaged pack conditions have already had a massive impact on the device.

The device may be damaged.

Do not dispose of the original packaging. Pack the device during transportation and storage.

1. When accepting a delivery, please check the packaging for visible transport damage.

2. If any transport damage is present at the time of delivery, lodge a complaint at the shipping company in charge. Have the shipper confirm the transport damage immediately.

3. Unpack the device at its installation location.

4. Keep the original packaging in case you have to transport the unit again.

aging indicates that ambient

5. Check the contents of the packaging and any accessories you may have ordered for completeness and damage.

SIMATIC IPC277D Operating Instructions, 12/2016, A5E03409486-AE

Installing and connecting the device

WARNING

Electric shock and fire hazard due to damaged device

NOTICE

Damage from condensation

3.1 Preparing for installation

6. If the contents of the packaging are incomplete, damaged or do not match your order, inform the responsible delivery service immediately. Fax the enclosed form "SIMATIC IPC/PG Quality Control Report".

A damaged device can be under hazardous voltage and trigger a fire in the machine or plant. A damaged device has unpredictable properties and states.

Death or serious injury could occur.

Make sure that the damaged device is not inadvertently installed and put into operation. Label the damaged device and keep it locked away. Send off the device for immediate repair.

If the device is subjected to low temperatures or extreme fluctuations in temperature during transportation, for example in cold weather, moisture could build up on or inside the HMI device.

Moisture can result in short-circuits in electrical circuits and damage the device.

In order to prevent damage to the device, proceed as follows:

• Store the device in a dry place.

• Bring the device to room temperature before starting it up.

• Do not expose the device to direct heat radiation from a heating device.

• If condensation develops, wait approximately 12 hours or until the device is

completely dry before switching it on.

7. Please keep the enclosed documentation in a safe place. It belongs to the device. You

the documentation when you commission the device for the first time.

need

8. Write down the identification data of the device.

30 Operating Instructions, 12/2016, A5E03409486-AE

SIMATIC IPC277D

+ 152 hidden pages

Siemens SIMATIC IPC277D Operating Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Legal information

Preface

Table of contents

Product description

SIMATIC IPC277D 7"

1.2 Configuration of the devices

SIMATIC IPC277D 9"

SIMATIC IPC277D 12", 15" and 19"

IPC277D 7" and 9" – interfaces and operator controls

IPC277D 12", 15" and 19" – interfaces and operator controls

1.3 Accessories

General safety instructions

2.2 Notes on usage

Preparing for installation

Checking the delivery package