Siemens SIMATIC IFP2200, SIMATIC IFP1900, SIMATIC IFP1500, SIMATIC IFP1900 ETH, SIMATIC IFP2200 ETH Operating Instructions Manual

...

Industrial Flat Panel IFP1500, IFP1900,

IFP2200, IFP1900 PRO, IFP2200 PRO, IFP1900 ETH, IFP2200 ETH

___________________

SIMATIC

Industrial Monitors Industrial Flat Panel IFP1500, IFP1900, IFP2200, IFP1900 PRO, IFP2200 PRO, IFP1900 ETH, IFP2200 ETH

Operating Instructions

07/2016

A5E31298376

Preface

Overview

Safety information

Installing and connecting the device

Commissioning the device

Operating the device

Maintaining and servicing your device

Technical information

Technical Support

List of abbreviations

-AF

Siemens AG Division Digital Factory Postfach 48 48 90026 NÜRNBERG GERMANY

A5E31298376-AF

Ⓟ

Legal information

Warning notice system

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

Qualified Personnel

personnel qualified

Proper use of Siemens products

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

maintenance are required to ensure that the products operate safely and without any problems. The permissible ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

Disclaimer of Liability

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage.

The product/system described in this documentation may be operated only by task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified personnel are those who, based on their training and experience, are capable of identifying risks and avoiding potential hazards when working with these products/systems.

Note the following:

documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

We have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions.

for the specific

08/2016 Subject to change

Preface

Basic knowledge required

Scope of the operating instructions

Scope of this documentation

These operating instructions contain all the information you need for commissioning and operation of the SIMATIC Industrial Flat Panel IFP.

It is intended both for programming and testing personnel who commission the device and connect it with other units (automation systems, programming devices), as well as for service and maintenance personnel who install add-ons or carry out fault/error analyses.

A solid background in personal computers and Microsoft operating systems is required to understand this manual. General knowledge in the field automation control engineering is recommended.

These operating instructions apply to the following Industrial Flat Panels with the order

numbers 6AV7863-.....-....:

● SIMATIC IFP1500, IFP1900, IFP2200

● SIMATIC IFP1900 ETH, IFP2200 ETH

● SIMATIC IFP1900 PRO, IFP2200 PRO

The SIMATIC Industrial Flat Panel is supplied with the following documents:

● In printed form: Quick Install Guide for the device, Installation and Commissioning Instructions

● Electronically as PDF file on the "Documentation and Drivers" CD/DVD:

– Operating instructions Industrial Flat Panel IFP1500, IFP1900, IFP2200,

IFP1900 ETH, IFP2200 ETH, IFP1900 PRO, IFP2200 PRO

– Operating manual SIMATIC Industry PC Panel Drivers and Tools PDT

You can find the operating manual in the PDT installation directory after installing PDT.

Industrial Flat Panel IFP1500, IFP1900, IFP2200, IFP1900 PRO, IFP2200 PRO, IFP1900 ETH, IFP2200 ETH Operating Instructions, 07/2016, A5E31298376-AF

Preface

Conventions

Figures

History

Edition

Comment

09/2012

First Edition

11/2014

Update with IPC Wizard 2.1 and corrections

07/2015

Corrections

In these operating instructions, the SIMATIC IFP is also referred to as "Flat Panel" or "device".

The devices SIMATIC IFP1900 ETH and IFP2200 ETH are also referred to as "Ethernet Monitor" and "ETH version".

A touch device generally refers to a device with a touch screen, as opposed to a pure "display device". Touch screen is the general term for a capacitive multi-touch screen and resistive single touch screen.

The devices IFP1500, IFP1900, IFP2200, IFP1900 ETH and IFP2200 ETH are referred to as "built-in units".

The devices IFP1900 PRO and PRO IFP2200 are referred to as "PRO devices".

At some places in these operating instructions, the general term "Windows Embedded Standard" is used to refer to "Windows Embedded Standard 2009" and "Windows Embedded Standard 7". "Windows 7" is used as an abbreviation for "Windows 7 Ultimate".

This manual contains figures of the described devices. The supplied device may differ in some details from the figures. Within some of the figures, one device is used to represent all Industrial Flat Panels.

The following earlier release versions of these operating instructions have been published:

06/2014 Description of devices with capacitive multi-touch screen

06/2015 The description of the following devices has been added:

• SIMATIC IFP1900 PRO, suitable for pedestal

• SIMATIC IFP1900 PRO, suitable for support arm

• SIMATIC IFP1900 ETH, IFP2200 ETH

07/2016 The description of the following devices has been added:

• SIMATIC IFP2200 PRO, suitable for support arm

• SIMATIC IFP2200 PRO, suitable for pedestal and extension components

• SIMATIC IFP1900 PRO, suitable for support arm and extension components

• SIMATIC IFP2200 PRO, suitable for support arm and extension components

Industrial Flat Panel IFP1500, IFP1900, IFP2200, IFP1900 PRO, IFP2200 PRO, IFP1900 ETH, IFP2200 ETH

4 Operating Instructions, 07/2016, A5E31298376-AF

Preface ................................................................................................................................................... 3

1 Overview................................................................................................................................................. 9

2 Safety information ................................................................................................................................. 27

3 Installing and connecting the device ...................................................................................................... 33

1.1 Product description ................................................................................................................... 9

1.2 Scope of delivery .................................................................................................................... 12

1.3 Design of the built-in units ...................................................................................................... 13

1.3.1 IFP1500/1900/2200 Multitouch, IFP1900/2200 ETH .............................................................. 13

1.3.2 IFP1500/1900/2200 Touch ..................................................................................................... 15

1.3.3 IFP1500 Touch/Key ................................................................................................................ 16

1.3.4 Interfaces ................................................................................................................................ 16

1.3.4.1 Standard versions ................................................................................................................... 16

1.3.4.2 Ethernet Monitor devices ........................................................................................................ 17

1.3.4.3 Extended versions .................................................................................................................. 17

1.4 Design of the PRO devices ..................................................................................................... 18

1.4.1 PRO devices, suitable for support arm ................................................................................... 18

1.4.2 PRO devices, suitable for pedestal and extension components ............................................ 19

1.4.3 PRO devices, suitable for support arm and extension components ....................................... 21

1.4.4 Interfaces ................................................................................................................................ 22

1.5 Accessories ............................................................................................................................. 23

1.6 System components for PRO devices .................................................................................... 24

2.1 General safety instructions ..................................................................................................... 27

2.2 Notes about usage .................................................................................................................. 30

3.1 Preparing for installation ......................................................................................................... 33

3.1.1 Checking the delivery package ............................................................................................... 33

3.1.2 Built-in unit .............................................................................................................................. 34

3.1.2.1 Permitted mounting positions ................................................................................................. 34

3.1.2.2 Checking clearances............................................................................................................... 36

3.1.2.3 Preparing the mounting cutout ................................................................................................ 37

3.1.2.4 Labeling the function keys ...................................................................................................... 38

3.1.3 PRO devices ........................................................................................................................... 40

3.1.3.1 Permitted mounting positions ................................................................................................. 40

3.2 Installing the built-in unit ......................................................................................................... 40

3.2.1 Notes on installation................................................................................................................ 40

3.2.2 Mounting clips or mounting brackets, position for IP65 .......................................................... 41

3.2.3 Fastening the device with mounting clips or mounting brackets ............................................ 43

3.2.4 Position of the mounting clips for IP66-complaint installation................................................. 44

Industrial Flat Panel IFP1500, IFP1900, IFP2200, IFP1900 PRO, IFP2200 PRO, IFP1900 ETH, IFP2200 ETH Operating Instructions, 07/2016, A5E31298376-AF

Table of contents

4 Commissioning the device .................................................................................................................... 63

5 Operating the device ............................................................................................................................. 65

6 Maintaining and servicing your device ................................................................................................... 73

3.3 Mounting the PRO device ...................................................................................................... 45

3.3.1 Notes on mounting ................................................................................................................. 45

3.3.2 PRO devices, suitable for support arm / pedestal and extension components ..................... 47

3.3.3 PRO devices, suitable for support arm and extension components ...................................... 49

3.4 Connecting the device ........................................................................................................... 51

3.4.1 Notes on connection .............................................................................................................. 51

3.4.2 Earthing the device ................................................................................................................ 52

3.4.3 Connecting the power supply ................................................................................................. 53

3.4.3.1 Connecting devices with 24 V DC 2-pin ................................................................................ 53

3.4.3.2 Connecting devices with 3-pin 24 V DC ................................................................................ 55

3.4.3.3 Connecting an AC power supply ............................................................................................ 56

3.4.4 Connecting IFP Standard, Extended and PRO to a PC ........................................................ 58

3.4.4.1 Overview ................................................................................................................................ 58

3.4.4.2 Standard version .................................................................................................................... 59

3.4.4.3 Extended version, PRO device .............................................................................................. 59

3.4.5 Connecting Ethernet Monitor to a PC .................................................................................... 60

3.4.5.1 Overview ................................................................................................................................ 60

3.4.5.2 Connection versions .............................................................................................................. 61

3.4.6 Connecting a USB device ...................................................................................................... 61

3.4.7 Securing the cables ............................................................................................................... 62

5.1 Operator input options ........................................................................................................... 65

5.2 Operating a device with resistive single touch screen ........................................................... 66

5.3 Operating a device with capacitive multi-touch screen .......................................................... 67

5.4 Operating a Touch/Key device............................................................................................... 69

5.5 Advanced device functions .................................................................................................... 72

6.1 Cleaning the device ............................................................................................................... 73

6.2 Ethernet Monitors - Diagnostics and reset ............................................................................. 74

6.2.1 Diagnostics screen ................................................................................................................. 74

6.2.2 Restoring the factory settings for an Ethernet Monitor .......................................................... 75

6.3 Spare parts and repairs ......................................................................................................... 76

6.4 Recycling and disposal .......................................................................................................... 76

Industrial Flat Panel IFP1500, IFP1900, IFP2200, IFP1900 PRO, IFP2200 PRO, IFP1900 ETH, IFP2200 ETH

6 Operating Instructions, 07/2016, A5E31298376-AF

Table of contents

7 Technical information ............................................................................................................................ 77

A Technical Support ............................................................................................................................... 111

B List of abbreviations ............................................................................................................................ 113

Glossary ............................................................................................................................................. 115

Index................................................................................................................................................... 117

7.1 Certificates and approvals ...................................................................................................... 77

7.2 Directives and declarations ..................................................................................................... 80

7.2.1 ESD guideline ......................................................................................................................... 80

7.2.2 Electromagnetic compatibility ................................................................................................. 82

7.3 Dimension drawings ................................................................................................................ 83

7.3.1 Dimension drawing of the IFP1500 Multitouch ....................................................................... 83

7.3.2 Dimension drawing of the IFP1500 Monitor and Touch ......................................................... 84

7.3.3 Dimension drawing of the IFP1900 Multitouch and IFP1900 ETH ......................................... 85

7.3.4 Dimension drawing of the IFP1900 Monitor and Touch ......................................................... 86

7.3.5 Dimension drawing of the IFP2200 Multitouch and IFP2200 ETH ......................................... 87

7.3.6 Dimension drawing of the IFP2200 Monitor and Touch ......................................................... 88

7.3.7 Dimension dimensional drawing of the IFP1900 PRO ........................................................... 89

7.3.8 Dimension drawing of the IFP2200 PRO ................................................................................ 92

7.3.9 Dimension drawing of the IFP1500 Touch/Key ...................................................................... 95

7.3.10 Dimension drawing Host Unit USB ......................................................................................... 96

7.3.11 Dimensions for labeling strips ................................................................................................. 97

7.4 Rating plate ............................................................................................................................. 98

7.5 Technical specifications .......................................................................................................... 98

7.5.1 General technical specifications ............................................................................................. 98

7.5.2 Ambient conditions ................................................................................................................ 101

7.5.2.1 Transport and storage conditions ......................................................................................... 101

7.5.2.2 Operating conditions ............................................................................................................. 102

7.5.2.3 Information on insulation tests, protection class and degree of protection........................... 105

7.6 Interface description .............................................................................................................. 106

7.6.1 24 V DC Power Supply ......................................................................................................... 106

7.6.2 DVI-D interface ..................................................................................................................... 108

7.6.3 DisplayPort ............................................................................................................................ 109

7.6.4 USB interface, Type B .......................................................................................................... 109

7.6.5 USB hub, Type A .................................................................................................................. 110

7.6.6 Ethernet ................................................................................................................................ 110

A.1 Service and support .............................................................................................................. 111

A.2 Troubleshooting .................................................................................................................... 112

Industrial Flat Panel IFP1500, IFP1900, IFP2200, IFP1900 PRO, IFP2200 PRO, IFP1900 ETH, IFP2200 ETH Operating Instructions, 07/2016, A5E31298376-AF

Table of contents

Industrial Flat Panel IFP1500, IFP1900, IFP2200, IFP1900 PRO, IFP2200 PRO, IFP1900 ETH, IFP2200 ETH

8 Operating Instructions, 07/2016, A5E31298376-AF

1.1

Product description

SIMATIC Industrial Flat Panels are LCD monitors suitable for industrial use with a brilliant TFT display which can be connected to all SIMATIC IPCs as well as almost all generally available PCs.

Industrial Flat Panel IFP1500, IFP1900, IFP2200, IFP1900 PRO, IFP2200 PRO, IFP1900 ETH, IFP2200 ETH Operating Instructions, 07/2016, A5E31298376-AF

Overview

Features of the built-in units

Additional features of the Extended versions

1.1 Product description

● Rugged front

● Brilliant TFT display with a wide reading angle;

Resistive single touch screen in sizes 15", 19" and 22"

Capacitive multi-touch screen available in sizes 15", 19" and 22"

● Available as pure display device (monitor) or touch device

● Can be placed up to 5 m from the IPC

● DVI-D and DisplayPort V1.1 interface

● Multi-monitoring support

● Backlighting can be dimmed via software

● 24 V DC power supply

● Degree of protection IP65 in installed state

● Enclosure type: Front face only Type 4X/Type 12 (indoor use only)

● Up to 16 million colors

● Up to 30 m away from PC possible via DVI

● Power supply (with USB) 24 V DC and 100-240 V AC

● 2 USB ports

● Also available as touch/key version with front USB interface

Industrial Flat Panel IFP1500, IFP1900, IFP2200, IFP1900 PRO, IFP2200 PRO, IFP1900 ETH, IFP2200 ETH

10 Operating Instructions, 07/2016, A5E31298376-AF

Overview

Additional features of the PRO devices

Additional features of the Ethernet Monitors

1.1 Product description

● All-round dust-proof and splash-proof with IP65 degree of protection and Enclosure Type 4X / 12 (indoor use only)

● Can be mounted directly on the machine

● 19" display, 22" display; capacitive multi-touch screen

● Device versions for mounting:

– IFP PRO, suitable for support arm (flange above)

– IFP PRO, suitable for support arm and extension components (round tube)

– IFP PRO, suitable for pedestal and extension components (flange below)

● Adapters and adapter sets that can be ordered separately support mounting systems from various manufacturers.

– Base adapter for device versions with flange above and flange below included in the

product package.

– For the IFP PRO device version, suitable for support arm and extension components:

- Cover for the mechanical interface below, included in the product package

- Flange mount available as accessory

● Can be placed up to 30 m away via DVI

● 2 USB ports

● Configuration and operation in the Ethernet/LAN network

● Length of the Ethernet/LAN connection as customary with conventional LAN technology

● Automatic establishment of connection to SIMATIC IPC

● Automatic configuration using 1:1 cable connection

● Ethernet Monitor software and monitor diagnostic function

Industrial Flat Panel IFP1500, IFP1900, IFP2200, IFP1900 PRO, IFP2200 PRO, IFP1900 ETH, IFP2200 ETH Operating Instructions, 07/2016, A5E31298376-AF

Overview

1.2

Scope of delivery

Name

Figure

Number

cable; 2 m in length, for commissioning

USB connecting cable, 2 m in length2

Ethernet connecting cable, 2 m in length3

Power supply cable 230 V AC 4

"Documentation and Drivers" CD

Only for PRO devices of the type "suitable for support arm and extension components"

1.2 Scope of delivery

The product package includes the following components:

Industrial Flat Panel

Installation instructions (Quick Install Guide)

Accessory kit "Mounting clips 1

and power supply connector"

"Connecting cables" accessory kit 1 DVI connecting cable or DisplayPort connecting

Base adapter 5

Cover for mechanical interface 6

Not with PRO devices Not with standard display device (monitor) Only with devices of the Ethernet Monitor type Only with devices with AC power supply Only for PRO devices of the type "suitable for support arm" and "suitable for pedestal and

extension components"

Industrial Flat Panel IFP1500, IFP1900, IFP2200, IFP1900 PRO, IFP2200 PRO, IFP1900 ETH, IFP2200 ETH

12 Operating Instructions, 07/2016, A5E31298376-AF

Overview

1.3

Design of the built-in units

1.3.1

IFP1500/1900/2200 Multitouch, IFP1900/2200 ETH

Front view and bottom view

①

Display/touch screen

②

Recesses for mounting clips

③

Mounting seal

1.3 Design of the built-in units

This section describes the design of the multi-touch devices, using the IFP1900 Multitouch as an example.

Industrial Flat Panel IFP1500, IFP1900, IFP2200, IFP1900 PRO, IFP2200 PRO, IFP1900 ETH, IFP2200 ETH Operating Instructions, 07/2016, A5E31298376-AF

Overview

Rear view

①

Rating plate

②

Interface name

③

Equipotential bonding

④

Retaining elements for strain relief of the connecting cables

1.3 Design of the built-in units

Industrial Flat Panel IFP1500, IFP1900, IFP2200, IFP1900 PRO, IFP2200 PRO, IFP1900 ETH, IFP2200 ETH

14 Operating Instructions, 07/2016, A5E31298376-AF

Overview

1.3.2

IFP1500/1900/2200 Touch

Front view and side view

①

Display/touch screen

②

Recesses for mounting clips

③

Mounting seal

Rear view

1.3 Design of the built-in units

This section describes the design of the monitor and touch devices, using the IFP1500 Touch as an example.

See section "IFP1500/1900/2200 Multitouch".

Industrial Flat Panel IFP1500, IFP1900, IFP2200, IFP1900 PRO, IFP2200 PRO, IFP1900 ETH, IFP2200 ETH Operating Instructions, 07/2016, A5E31298376-AF

Overview

1.3.3

IFP1500 Touch/Key

Front view

①

Display and function keys with LED

②

Alphanumeric keys

③

Control keys

④

Cursor keys

⑤

USB port

1.3.4

Interfaces

1.3.4.1

Standard versions

①

X80 connector for 24 V DC power supply

②

X71 DVI-D interface

③

X70 DisplayPort interface

④

X60 USB Type B

1.3 Design of the built-in units

Industrial Flat Panel IFP1500, IFP1900, IFP2200, IFP1900 PRO, IFP2200 PRO, IFP1900 ETH, IFP2200 ETH

16 Operating Instructions, 07/2016, A5E31298376-AF

Overview

1.3.4.2

Ethernet Monitor devices

①

X80 connector for 24 V DC power supply

②

X1 Ethernet port

③

Reset button

④

X70 DisplayPort interface

⑤

X61/X62 USB Type A

⑥

X60 USB Type B

1.3.4.3

Extended versions

①

Connection for 100 to 240 V AC power supply

⑤

X61/X62 USB Type A

②

X80 connector for 24 V DC power supply

⑥

X63 USB link interface

③

X71 DVI-D interface

⑦

X60 USB Type B

④

X70 DisplayPort interface

1.3 Design of the built-in units

Industrial Flat Panel IFP1500, IFP1900, IFP2200, IFP1900 PRO, IFP2200 PRO, IFP1900 ETH, IFP2200 ETH Operating Instructions, 07/2016, A5E31298376-AF

Overview

1.4

Design of the PRO devices

1.4.1

PRO devices, suitable for support arm

Front view and side view

①

Display with touch screen

②

Enclosure

③

Backplane cover

Top view

①

Mechanical interface for fastening

1.4 Design of the PRO devices

The following figures show the design of the devices using IFP1900 PRO suitable for support arm as an example.

Industrial Flat Panel IFP1500, IFP1900, IFP2200, IFP1900 PRO, IFP2200 PRO, IFP1900 ETH, IFP2200 ETH

18 Operating Instructions, 07/2016, A5E31298376-AF

Overview

Rear view

①

Mechanical interface for fastening

②

Rating plate

③

Enclosure

④

Backplane cover

1.4.2

PRO devices, suitable for pedestal and extension components

Front view and side view

①

Display with touch screen

②

Enclosure

③

Backplane cover

1.4 Design of the PRO devices

The following figures shows the design of the devices using IFP1900 PRO suitable for pedestal and extension components as an example.

Industrial Flat Panel IFP1500, IFP1900, IFP2200, IFP1900 PRO, IFP2200 PRO, IFP1900 ETH, IFP2200 ETH Operating Instructions, 07/2016, A5E31298376-AF

Overview

Bottom view

①

Mechanical interface for fastening

Rear view

①

Backplane cover

②

Enclosure

③

Rating plate

④

Mechanical interface for fastening

1.4 Design of the PRO devices

Industrial Flat Panel IFP1500, IFP1900, IFP2200, IFP1900 PRO, IFP2200 PRO, IFP1900 ETH, IFP2200 ETH

20 Operating Instructions, 07/2016, A5E31298376-AF

Overview

1.4.3

PRO devices, suitable for support arm and extension components

Front view and side view

①

Display with touch screen

②

Enclosure

③

Mechanical interface for fastening (round tube)

④

Terminal compartment cover

⑤

Mechanical interface below

1.4 Design of the PRO devices

The following figures show the design of the devices using IFP1900 PRO suitable for support arm and extension components as an example.

Industrial Flat Panel IFP1500, IFP1900, IFP2200, IFP1900 PRO, IFP2200 PRO, IFP1900 ETH, IFP2200 ETH Operating Instructions, 07/2016, A5E31298376-AF

Overview

Rear view

①

Mechanical interface for fastening (round tube)

②

Terminal compartment cover

③

Nameplate

④

Mechanical interface below

⑤

Lower cover, included in the product package

1.4.4

Interfaces

①

Protective conductor terminal

⑤

X61/X62 USB Type A

②

X80 connector for 24 V DC power supply

⑥

X63 USB link interface

③

X71 DVI-D interface

⑦

X60 USB Type B

④

X70 DisplayPort interface

1.4 Design of the PRO devices

Industrial Flat Panel IFP1500, IFP1900, IFP2200, IFP1900 PRO, IFP2200 PRO, IFP1900 ETH, IFP2200 ETH

22 Operating Instructions, 07/2016, A5E31298376-AF

Overview

1.5

Accessories

Introduction

All Industrial Flat Panels

Name

Specification

Article number

3 m long

6AV7860-0BH30-0AA0

3 m long

6AV7860-0DH30-0AA0

3 m long

6AV7860-0CH30-0AA0

5 m long

6AV7860-0CH50-0AA0

15"

6AV2124-6QJ00-0AX0

19"

6AV2124-6UJ00-0AX0

22"

6AV2124-6XJ00-0AX0

For resistive touch screen

6AV7672-1JB00-0AA0

For capacitive and resistive touch screen

6AV2181-8AV20-0AX0

Built-in units

Name

Specification

Article number

Mounting clips service pack

20 pieces

6AV6671-8XK00-0AX3

Mounting brackets service pack

2 x 8 latch fasteners

6AV7672-1JC00-0AA0

Extended version

Name

Specification

Article number

10 m long

6AV7860-1EX21-0AA1

15 m long

6AV7860-1EX21-5AA1

20 m long

6AV7860-1EX22-0AA1

30 m long

6AV7860-1EX23-0AA1

1.5 Accessories

This section contains the number of accessories available at the time of publication of the operating instructions. You will find additional accessories on the Internet at:

● Industry Mall (https://mall.industry.siemens.com)

● Expansion components and accessories (http://www.automation.siemens.com/mcms/pc-

based-automation/en/industrial-pc/expansion_components_accessories)

● Ethernet cable accessories (https://support.industry.siemens.com/cs/ww/en/view/98278804

DVI line

DisplayPort line

USB line

5 m long 6AV7860-0BH50-0AA0

5 m long 6AV7860-0DH50-0AA0

)

Protective foil for the touch screen

Touch pen

Cable set (DVI/USB cable)

Industrial Flat Panel IFP1500, IFP1900, IFP2200, IFP1900 PRO, IFP2200 PRO, IFP1900 ETH, IFP2200 ETH Operating Instructions, 07/2016, A5E31298376-AF

Overview

Touch/Key Extended version

Name

Article number

Drivers" CD/DVD.

Ethernet Monitors

Name

Specification

Article number

TP Cord RJ45/RJ45, 15 m

6XV1870-3QN15

TP Cord RJ45/RJ45, 20 m

6XV1870-3QN20

TP Cord RJ45/RJ45, 30 m

6XV1870-3QN30

TP Cord RJ45/RJ45, 50 m

6XV1870-3QN50

1.6

System components for PRO devices

Base adapter

①

Seal

②

Channel cable

③

Mechanical interface to the PRO device

④

Cover

⑤

Mechanical interface to the support arm or pedestal including seal

1.6 System components for PRO devices

Film for labeling the function keys (slide-in labels)

Recommended Ethernet RJ45 cables (selection)

Print templates for the slide-in labels are available on the "Documentation and

6AV7672-0DA00-0AA0

Additional Ethernet cables: See link "Accessories Ethernet cables" at the beginning of this section.

PRO devices of the type "suitable for support arm" or "suitable for pedestal" can be mounted on the support arm or pedestal using the base adapter. A base adapter is included with the corresponding PRO devices. The base adapter can also be ordered separately.

Article number: 6AV7674-1KA00-0AA0

Industrial Flat Panel IFP1500, IFP1900, IFP2200, IFP1900 PRO, IFP2200 PRO, IFP1900 ETH, IFP2200 ETH

24 Operating Instructions, 07/2016, A5E31298376-AF

Overview

Adapter sets and couplings

Adapter version

Suitable for supporting arm systems

Article number

SIEMENS

RITTAL

ROLEC

BERNSTEIN

All information subject to change.

1.6 System components for PRO devices

The following mechanical adapter versions are also available for mounting a PRO device of the types "suitable for support arm" and "suitable for pedestal" via the base adapter:

● A Siemens VESA adapter set for VESA compatible systems

● Manufacturer-specific adapter or couplings

The following table shows the available Siemens adapter sets and examples of vendorspecific adapter versions:

• Adapter set VESA75

• Adapter set VESA100

Adapter for Siemens PRO Panel

• Intermediate plate

• Screws

Adapter for Siemens PRO Panel

• Intermediate plate

• Screws

Coupling for Siemens SIMATIC PRO

• No intermediate plate required

• Coupling with integrated adaptation for PRO devices

VESA75-compatible systems 6AV7674-0KE00-0AA0

VESA100-compatible systems 6AV7674-0KD00-0AA0

• CP40 steel

• CP60/120 for support arm

connection 120 × 65 mm

• profiPlus-50

• taraPLUS for ∅ 65 mm hole circle

• CS-3000 • 1015300187 RAL 9006

6206.500

142.024.000

White aluminum

• 1015300043 RAL 7016 Anthracite grey

Industrial Flat Panel IFP1500, IFP1900, IFP2200, IFP1900 PRO, IFP2200 PRO, IFP1900 ETH, IFP2200 ETH Operating Instructions, 07/2016, A5E31298376-AF

Overview

Flange mount

①

Flange mount

②

Ring groove for fastening on PRO device with setscrews

③

Mechanical interface to support arm

1.6 System components for PRO devices

A flange mount is available for mounting a PRO device of the type "suitable for support arm and extension components".

Article number: 6AV7674-1KF00-0AA0

You can find additional system components for PRO devices on the Internet (

https://mall.industry.siemens.com/mall/en/WW/Catalog/Products/10299123?tree=CatalogTr

ee).

Industrial Flat Panel IFP1500, IFP1900, IFP2200, IFP1900 PRO, IFP2200 PRO, IFP1900 ETH, IFP2200 ETH

26 Operating Instructions, 07/2016, A5E31298376-AF

2.1

General safety instructions

Machinery Directive

WARNING

The device may only be used in machines which comply with the Machinery Directive

Hazardous areas

WARNING

Explosion Hazard

Risque d'Explosion

The Machinery Directive specifies precautions to be taken when commissioning and operating machinery within the European Economic Area.

Failure to follow these precautions is a breach of the Machinery Directive. Such failure may also cause personal injury and damage depending on the machine operated.

The machine in which the HMI device is to be operated must conform to Directive 2006/42/EC.

When operating the HMI device in hazardous areas the following warning applies.

Do not disconnect while circuit is live unless area is known to be non-hazardous. Substitution of components may impair suitability for Class I, Division 2 or Zone 2.

Ne pas déconnecter pendant que le circuit est sous tension, sauf si la zone est nondangereuse. Le remplacement de composants peut compromettre leur capacité à satisfaire à la Classe I, Division 2 ou Zone 2.

Industrial Flat Panel IFP1500, IFP1900, IFP2200, IFP1900 PRO, IFP2200 PRO, IFP1900 ETH, IFP2200 ETH Operating Instructions, 07/2016, A5E31298376-AF

Safety information

Strong high-frequency radiation

NOTICE

Observe immunity to RF radiation

Additional notes for built-in units

WARNING

The device constitutes open equipment

Life-threatening voltages are present with an open control cabinet

2.1 General safety instructions

The device has increased immunity to RF radiation according to the specifications on electromagnetic compatibility in the technical specifications.

Radiation exposure in excess of the specified immunity limits can impair device functions, result in malfunctions and therefore injuries or damages.

Read the information on immunity to RF radiation in the technical specifications.

The device constitutes open equipment. This means that the device may only be installed in enclosures or cabinets which provide front access for operating the device.

When you open the control cabinet, some areas or components may be conducting life-threatening voltages.

Contact with these areas or components may result in death by electric shock.

Switch off the power supply to the cabinet before opening it.

Industrial Flat Panel IFP1500, IFP1900, IFP2200, IFP1900 PRO, IFP2200 PRO, IFP1900 ETH, IFP2200 ETH

28 Operating Instructions, 07/2016, A5E31298376-AF

Safety information

Industrial Security

Disclaimer for third-party software updates

Notes on protecting administrator accounts

2.2 Notes about usage

The device may be damaged if operated outdoors.

• "Indoor use only"

• Operate the device indoors only.

The device is designed for industrial use. It conforms to the following standards:

● Requirements of the emission standard for industrial environments, EN 61000-6-4: 2007

● Requirements for interference immunity EN 61000-6-2: 2005

● Immunity to interference acc. to EN 55024

● Radio interference suppression acc. to EN 55022, Class B

If you operate the device in a residential area, you must ensure conformance to Class B limits according to EN 55011 regarding the emission of radio interference.

Suitable measures for achieving the degree of noise suppression for Limit Class B include, for example:

● Install built-in units in grounded control cabinets

● Use of filters in electrical supply lines

Individual acceptance is required.

Industrial Flat Panel IFP1500, IFP1900, IFP2200, IFP1900 PRO, IFP2200 PRO, IFP1900 ETH, IFP2200 ETH

30 Operating Instructions, 07/2016, A5E31298376-AF

+ 90 hidden pages

Siemens SIMATIC IFP2200, SIMATIC IFP1900, SIMATIC IFP1500, SIMATIC IFP1900 ETH, SIMATIC IFP2200 ETH Operating Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Industrial Flat Panel IFP1500, IFP1900,

IFP2200, IFP1900 PRO, IFP2200 PRO, IFP1900 ETH, IFP2200 ETH

Legal information

Preface

Table of contents

Product description

1.2 Scope of delivery

IFP1500/1900/2200 Multitouch, IFP1900/2200 ETH

1.3 Design of the built-in units

IFP1500/1900/2200 Touch

IFP1500 Touch/Key

Interfaces

Standard versions

Ethernet Monitor devices

Extended versions

PRO devices, suitable for support arm

1.4 Design of the PRO devices

PRO devices, suitable for pedestal and extension components

PRO devices, suitable for support arm and extension components

Interfaces

1.5 Accessories

1.6 System components for PRO devices

General safety instructions

2.2 Notes about usage