Siemens SIMATIC HMI TP900 Operator's Manual
Function Manual
Operator Panel
10/2016Edition
SIMATIC HMI
TP900
www.siemens.com
Medium-voltage converters
SIMATIC
TP900 Function Manual
Function Manual
10/2016
A5E39487277A
Introduction
1
Safety notes
2
Description
3
Screens
4
Installing software
5
Service & Support
A
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be
used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property
damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified
personnel are those who, based on their training and experience, are capable of identifying risks and avoiding
potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software described.
Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in
this publication is reviewed regularly and any necessary corrections are included in subsequent editions.
Siemens AG
Division Process Industries and Drives
Postfach 48 48
90026 NÜRNBERG
GERMANY
Document order number: A5E39487277A
Ⓟ 12/2016 Subject to change
Copyright © Siemens AG 2016.
All rights reserved
Table of contents
1 Introduction...................................................................................................................................................7
1.1 About these instructions...........................................................................................................7
2 Safety notes..................................................................................................................................................9
3 Description..................................................................................................................................................11
3.1 TP900 operator panel............................................................................................................11
3.2 Screen display areas..............................................................................................................12
3.3 Color information ...................................................................................................................15
3.4 Setting the screen..................................................................................................................16
4 Screens......................................................................................................................................................17
4.1 Overview screen....................................................................................................................17
4.2 "Status" screen selection.......................................................................................................18
4.2.1 "DC Link" screen....................................................................................................................18
4.2.2 "Recooling Unit" screen.........................................................................................................19
4.2.3 "Power Cells" screen..............................................................................................................19
4.2.4 "Drive" screen........................................................................................................................20
4.2.5 "Infeed" screen.......................................................................................................................21
4.3 "Temperature" screen selection.............................................................................................22
4.3.1 "Temperature" screen............................................................................................................22
4.4 "Trace" screen selection........................................................................................................23
4.4.1 "Trace" screen........................................................................................................................23
4.5 "Fault/Alarm" screen selection...............................................................................................25
4.5.1 "Fault/Alarm" screen..............................................................................................................25
4.6 "Local Operation" screen selection........................................................................................26
4.6.1 "Speed control" screen...........................................................................................................26
4.6.2 "Parameters" screen..............................................................................................................27
4.6.3 "Expert" screen......................................................................................................................28
5 Installing software.......................................................................................................................................29
5.1 Setting up the operator panel.................................................................................................29
A Service & Support.......................................................................................................................................31
Index...........................................................................................................................................................33
TP900 Function Manual
Function Manual, 10/2016, A5E39487277A 5
Table of contents
TP900 Function Manual
6 Function Manual, 10/2016, A5E39487277A
Introduction
1
1.1 About these instructions
These instructions describe the software and functions of the TP900 operator panel and how
to work with it.
These instruction are valid as of software version 1.9.9.2.
Keep these instructions for later use. Read these instructions before you work with the operator
panel and follow the instructions.
If you have suggestions for improving the document, please contact our Service Center.
Additional documents
Further information can be found in the following documentation:
● Converter operating instructions
● Converter List Manual
TP900 Function Manual
Function Manual, 10/2016, A5E39487277A 7
Introduction
1.1 About these instructions
TP900 Function Manual
8 Function Manual, 10/2016, A5E39487277A
Safety notes
2
It is essential that you follow all the safety instructions listed in the converter operating
instructions, for your own safety, to protect other people and to avoid damage to property.
The product/system described in this documentation may only be operated by personnel
qualified for the specific task in accordance with the relevant documentation for the specific
task, in particular its warning notices and safety instructions. Because of their training and
experience, qualified personnel can recognize any risks involved with handling these products/
systems and avoid any possible dangers.
For your own personal safety and to prevent material damage when carrying out any work,
always observe the safety-relevant instructions and the following five safety rules according
to EN 50110‑1 "Working in a voltage-free state". Apply the five safety rules in the sequence
stated before starting work.
Five safety rules
1. Disconnect the system.
Also disconnect the auxiliary circuits, for example, anti-condensation heating.
2. Secure against reconnection.
3. Verify absence of operating voltage.
4. Ground and short-circuit.
5. Provide protection against adjacent live parts.
To energize the system, apply the measures in reverse order.
TP900 Function Manual
Function Manual, 10/2016, A5E39487277A 9
Safety notes
TP900 Function Manual
10 Function Manual, 10/2016, A5E39487277A
Description
3
3.1 TP900 operator panel
The converter is operated and diagnosed using the operator panel.
Figure 3-1 Operator panel
The operator panel communicates with the drive via Ethernet.
The operator panel has the following functions:
● Touch-screen operation
● Screen saver
● Language switching
● Local operation
● TRACE function
● Display of converter faults and alarms
● Fault memory, can be read out via USB
TP900 Function Manual
Function Manual, 10/2016, A5E39487277A 11
Loading...