Siemens SIMATIC HMI IPC477C Comapct Operating Instructions
SIMATIC HMI IPC477C / HMI IPC477C
PRO
_
_________________
_
SIMATIC
Industrial PC
SIMATIC HMI IPC477C / HMI IPC477C PRO
Compact Operating Instructions
10/2010
A5E02368072-02
Compact Operating
Instructions
1
Legal information
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.
CAUTION
without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.
NOTICE
indicates that an unintended result or situation can occur if the corresponding information is not taken into
account.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation for the specific task, in particular its warning notices and
safety instructions. Qualified personnel are those who, based on their training and experience, are capable of
identifying risks and avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be adhered to. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this
publication may be trademarks whose use by third parties for their own purposes could violate the rights of the
owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Industry Sector
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E02368072-02
Ⓟ 11/2010
Copyright © Siemens AG 2010.
Technical data subject to change
SIMATIC HMI IPC477C / HMI IPC477C PRO
Compact Operating Instructions, 10/2010, A5E02368072-02
3
Table of contents
1 Compact Operating Instructions ................................................................................................................ 5
1.1
Safety instructions..........................................................................................................................5
1.2
Unpacking and checking the delivery ............................................................................................5
1.3
Components of the Product ...........................................................................................................6
1.4
Device identification data...............................................................................................................7
1.5
Accessories....................................................................................................................................8
1.6
Affixing Labeling Strips for Function Keys and Softkeys ...............................................................8
1.7
Installing/Mounting .......................................................................................................................11
1.7.1
Permitted mounting positions.......................................................................................................11
1.7.2
Preparing the mounting cut-out....................................................................................................12
1.7.3
Securing the Device with Clamps ................................................................................................13
1.7.4
Securing the Device with Screws.................................................................................................15
1.8
Connecting...................................................................................................................................17
1.8.1
Connection elements and operator controls ................................................................................17
1.8.2
Connecting the 24 VDC power supply.........................................................................................19
1.8.3
Connecting the PE conductor ......................................................................................................21
1.9
Commissioning.............................................................................................................................22
1.9.1
Commissioning Information .........................................................................................................22
1.9.2
Basic commissioning - initial startup............................................................................................23
1.9.3
Setting up the language selection in Windows Embedded Standard 2009.................................24
1.9.4
Language selection in Windows Embedded Standard 7.............................................................25
1.9.5
Setting the panel type ..................................................................................................................26
1.9.5.1
First commissioning .....................................................................................................................26
1.9.5.2
Touch panel configuration............................................................................................................27
1.9.5.3
Key panel configuration ...............................................................................................................28
1.9.5.4
Automatic restart..........................................................................................................................29
1.9.6
Device with key panel ..................................................................................................................29
1.9.6.1
Activating KeyTools .....................................................................................................................29
1.9.7
Device with touch screen.............................................................................................................30
1.9.7.1
Recalibrating the Touch Screen...................................................................................................30
1.9.7.2
Activating the Screen Keyboard ..................................................................................................33
1.10
Service and support.....................................................................................................................34
Index........................................................................................................................................................ 35
Table of contents
SIMATIC HMI IPC477C / HMI IPC477C PRO
4 Compact Operating Instructions, 10/2010, A5E02368072-02
SIMATIC HMI IPC477C / HMI IPC477C PRO
Compact Operating Instructions, 10/2010, A5E02368072-02
5
Compact Operating Instructions
1
1.1 Safety instructions
CAUTION
In order to avoid substantial damage and for your own safety, note the safety instructions in
this documentation and in the operating instructions.
WARNING
Function test while installing the device in machines or execute systems
Following the results of a risk analysis, additional protection equipment on the machine or
the system is necessary to avoid endangering persons. With this, especially the
programming, configuration and wiring of the inserted I/O modules have to be executed, in
accordance with the safety performance (SIL, PL or Cat.) identified by the necessary risk
analysis. The intended use of the device has to be ensured.
The correct use of the device has to be verified with a function test on the system. This test
can detect programming, configuration and wiring errors. The test results have to be
documented and, if necessary, entered into the relevant documents that verify safety.
1.2 Unpacking and checking the delivery
1. Please check the packaging material for transport damage upon delivery.
2. If any transport damage is present at the time of delivery, lodge a complaint at the
shipping company in charge. Have the shipper confirm the transport damage
immediately.
3. Unpack the device.
NOTICE
Lie the front side on a soft surface to avoid damaging the front panel USB port.
4. Keep the packaging material in case you have to transport the unit again.
Note
The packaging protects the device during transport and storage. Therefore, never
dispose of the original packaging material!
5. Please keep the enclosed documentation in a safe place. You will need the
documentation when you start up the device for the first time.
Compact Operating Instructions
1.3 Components of the Product
SIMATIC HMI IPC477C / HMI IPC477C PRO
6 Compact Operating Instructions, 10/2010, A5E02368072-02
6. Check the contents of the package for completeness and transportation damage. Check
for completeness using the enclosed scope of delivery list.
7. Should the contents of the package be incomplete or damaged, please inform the
responsible supply service immediately and fax us the enclosed form "SIMATIC IPC/PG
quality control report".
WARNING
Make sure that a damaged device is not installed nor put into operation.
8. Note the identification information (see chapter "Identification data of the device").
Notes on display
A small number of faults in the display is unavoidable.
Bad pixels Permissible number
Permanently bright and permanently dark pixels ≤ 12
Permanently bright, green pixels ≤ 5
1.3 Components of the Product
Scope of delivery for SIMATIC HMI IPC477C
Number Name Description
1 SIMATIC HMI IPC477C
1 Documentation and Drivers CD/DVD Contains the documentation and the hardware
drivers.
1 Operating instructions (compact)
SIMATIC HMI IPC 477C / HMI IPC477C
PRO
Printed copy in German and English of
Operating Instructions (compact).
6 Clamp Mounting clamp for SIMATIC HMI IPC477C.
1 DC power plug Only supply variant with 24 V DC power supply.
Compact Operating Instructions
1.4 Device identification data
SIMATIC HMI IPC477C / HMI IPC477C PRO
Compact Operating Instructions, 10/2010, A5E02368072-02
7
Scope of delivery for SIMATIC HMI IPC477C PRO
Number Name Description
1 SIMATIC HMI IPC477C PRO
1 Documentation and Drivers CD/DVD Contains the documentation and the hardware
drivers.
1 Operating instructions (compact)
SIMATIC HMI IPC 477C / HMI IPC477C
PRO
Printed copy in German and English of
Operating Instructions (compact).
1 Basic adapter Basic adapter as a basic element for mounting
to a supporting arm
4 Screws Screws for mounting the basic adapter to an
adapter
1 DC power plug Only supply variant with 24 V DC power supply.
1.4 Device identification data
Enter the identification data of the device into the table.
Serial number (on the type plate) S VP ...
Order no. of the device 6AV7 884-... (SIMATIC HMI IPC477C)
6AV7 883-... (SIMATIC HMI IPC477 PRO)
For the versions with
Windows Embedded Standard / XP Professional /
Windows 7:
Microsoft Windows Product Key from the
"Certificate of Authenticity" (COA)
Ethernet address 1
In the BIOS Setup (F2 Key) under Main >
Hardware Options > Ethernet Address
Ethernet address 2
(not for PROFINET versions) in BIOS Setup (F2
key) under Main > Hardware Options > Ethernet
Address
CP 1616 onboard MAC address layer 2
CP 1616 onboard Mac address PROFINET
Compact Operating Instructions
1.5 Accessories
SIMATIC HMI IPC477C / HMI IPC477C PRO
8 Compact Operating Instructions, 10/2010, A5E02368072-02
1.5 Accessories
These accessories are not included in the product package.
Accessories Order no.
2 GB Compact Flash card 6ES7648 - 2BF02 - 0XF0
4 GB Compact Flash card 6ES7648 - 2BF02 - 0XG0
8 GB Compact Flash card 6ES7648 - 2BF02 - 0XH0
1 GB DDR3 memory module 6ES7648 - 2AH40 - 0AH0
2 GB DDR3 memory module 6ES7648 - 2AH50 - 0AH0
4 GB DDR3 memory module 6ES7648 - 2AH60 - 0AH0
Touch pen 6AV7672 - 1JB00 - 0AA0
Note
Replace Compact Flash cards only with cards of the same product versions
Only SIMATIC PC Compact Flash cards with product version number 02 (ES 02 or higher)
can be used for this device.
1.6 Affixing Labeling Strips for Function Keys and Softkeys
Note
The following table applies only to devices with a key panel.
The control unit has two horizontal and two vertical keypads for the function keys and the
softkeys. Assign user specific functions to the keys as needed. You can mark these keys
with labeling strips. A4 films for creating the labeling strips are available as accessories.
Proceed as follows to affix the labeling strips:
Compact Operating Instructions
1.6 Affixing Labeling Strips for Function Keys and Softkeys
SIMATIC HMI IPC477C / HMI IPC477C PRO
Compact Operating Instructions, 10/2010, A5E02368072-02
9
Preparing the labeling strips
1. Label the DIN A4 film with a laser printer, for example using the printing templates
provided on the Documentation and Drivers CD.
2. Cut the labeling strips along the pre-printed lines.
Note
Do not insert handwritten labeling strips until the ink has dried.
Affixing the labeling strips
Insert the labeling strips into the slots provided on the rear of the control unit.
① Insert strips, vertical key rows
② Insert strips, horizontal key rows
Figure 1-1 12" touch screen device: Device rear with labeling strips
Compact Operating Instructions
1.6 Affixing Labeling Strips for Function Keys and Softkeys
SIMATIC HMI IPC477C / HMI IPC477C PRO
10 Compact Operating Instructions, 10/2010, A5E02368072-02
① Insert strips, vertical key rows
② Insert strips, horizontal key rows
Figure 1-2 15" touch screen device: Device rear with labeling strips
Compact Operating Instructions
1.7 Installing/Mounting
SIMATIC HMI IPC477C / HMI IPC477C PRO
Compact Operating Instructions, 10/2010, A5E02368072-02
11
1.7 Installing/Mounting
1.7.1 Permitted mounting positions
Mounting positions
Only vertical mounting at angles up to +45° and -45° are permitted for the device.
$%
Temperature at the device
Rear Front
Angle A Angle B
0° - 50° C1) Max. 40°C +45° -45°
0° to 45°C 0° to 45°C +45° -45°
1)
For RAL mounting only (RAL = Restricted Access Location)
(installation of device in operating facilities with restricted access - for example, a locked
control cabinet)
Mechanical environmental conditions
● Vibration
– Operation, tested in accordance with DIN IEC 60068-2-6
10 to 58 Hz: 0.075 mm 58 to 200 Hz: 9.8 m/s²
– Storage/transport, tested according to IEC 60068-2-27, IEC 60068-2-29
50 m/s², 30 ms
250 m/s², 6 ms
Loading...