Siemens SCALANCE X101-1,SCALANCE X101-1LD Operating Instructions Manual

SCALANCE X-100 media converter

___________________

SIMATIC NET

Industrial Ethernet switches SCALANCE X-100 media converter

Operating Instructions

04/2016

C79000

-G8976-C346-02

Introduction

Network topologies

Description of the device

Installation

Connecting up

Maintenance

Technical specifications

Approvals

Dimension drawings

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified personnel are those who, based on their training and experience, are capable of identifying risks and avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions.

SCALANCE X-100 media converter Operating Instructions, 04/2016, C79000-G8976-C346-02

Table of contents

1 Introduction ............................................................................................................................................. 5

1.1 On the Operating Instructions ................................................................................................... 5

1.2 On the product .......................................................................................................................... 7

2 Network topologies ............................................................................................................................... 11

2.1 Possible network topologies ................................................................................................... 11

2.2 Coupling of network segments ............................................................................................... 14

3 Description of the device ....................................................................................................................... 15

3.1 Overview of the SCALANCE X-100 media converters ........................................................... 15

3.2 Product characteristics............................................................................................................ 16

3.2.1 SCALANCE X101-1 ................................................................................................................ 16

3.2.2 SCALANCE X101-1LD ........................................................................................................... 17

3.3 TP ports (twisted pair) ............................................................................................................. 18

3.4 FO port (fiber optic) ................................................................................................................. 20

3.4.1 SCALANCE X101-1 ................................................................................................................ 20

3.4.2 SCALANCE X101-1LD ........................................................................................................... 21

3.5 LEDs ....................................................................................................................................... 22

3.6 SET button .............................................................................................................................. 24

3.7 Cascading two media converters ............................................................................................ 26

4 Installation ............................................................................................................................................ 27

4.1 Types of installation ................................................................................................................ 27

4.2 Installation on a DIN rail .......................................................................................................... 28

4.3 Installation on a standard rail .................................................................................................. 30

4.4 Wall mounting ......................................................................................................................... 31

5 Connecting up ....................................................................................................................................... 33

5.1 Wiring rules ............................................................................................................................. 33

5.2 Power supply .......................................................................................................................... 33

5.3 Signaling contact ..................................................................................................................... 35

5.4 Grounding ............................................................................................................................... 36

5.5 IE FC RJ-45 Plug 180 ............................................................................................................. 36

6 Maintenance ......................................................................................................................................... 39

7 Technical specifications ........................................................................................................................ 41

7.1 SCALANCE X101-1 ................................................................................................................ 41

Table of contents

SCALANCE X-100 media converter

4 Operating Instructions, 04/2016, C79000-G8976-C346-02

7.2 SCALANCE X101-1LD .......................................................................................................... 43

8 Approvals ............................................................................................................................................. 47

9 Dimension drawings .............................................................................................................................. 51

Index .................................................................................................................................................... 55

SCALANCE X-100 media converter Operating Instructions, 04/2016, C79000-G8976-C346-02

1.1

On the Operating Instructions

Purpose of the Operating Instructions

These operating instructions support you when commissioning networks with the media converters of the SCALANCE X-100.

Validity of the Operating Instructions

These operating instructions are valid for the following devices:

Device

Article number

SCALANCE X101-1 6GK5101-1BB00-2AA3

SCALANCE X101-1LD

6GK5101-1BC00-2AA3

Further documentation

The "SIMATIC NET Industrial Ethernet Twisted Pair and Fiber Optic Networks" manual contains additional information on other SIMATIC NET products that you can operate along with the media converters of the SCALANCE X-100 product line in an Industrial Ethernet network.

You can order the manual "SIMATIC NET Industrial Twisted Pair and Fiber Optic Networks", release 05/2001, using the following order numbers: 6GK1970-1BA10-0AA0 German 6GK1970-1BA10-0AA1 English 6GK1970-1BA10-0AA2 French 6GK1970-1BA10-0AA4 Italian

You will also find this network manual on the Internet pages of Service & Support under the following entry ID: 1172207 (http://support.automation.siemens.com/WW/view/en/1172207

You will find further information in the "System Manual Industrial Ethernet" in the Manual Collection.

You will find further information on the SCALANCE system on the Internet at www.siemens.com/scalance (www.siemens.com/scalance

You can obtain the "PROFINET Installation Guide" from the PROFIBUS User Organization (PNO).

Audience

These Operating Instructions are intended for persons commissioning networks with SCALANCE X-100 media converters.

Introduction

1.1 On the Operating Instructions

SCALANCE X-100 media converter

6 Operating Instructions, 04/2016, C79000-G8976-C346-02

SIMATIC NET glossary

Explanations of many of the specialist terms used in this documentation can be found in the SIMATIC NET glossary.

You will find the SIMATIC NET glossary on the Internet at the following address:

50305045 (http://support.automation.siemens.com/WW/view/en/50305045

)

Security information

Siemens provides products and solutions with industrial security functions that support the secure operation of plants, solutions, machines, equipment and/or networks. They are important components in a holistic industrial security concept. With this in mind, Siemens’ products and solutions undergo continuous development. Siemens recommends strongly that you regularly check for product updates.

For the secure operation of Siemens products and solutions, it is necessary to take suitable preventive action (e.g. cell protection concept) and integrate each component into a holistic, state-of-the-art industrial security concept. Third-party products that may be in use should also be considered. You will find more information about Industrial Security in: Industrial security (http://www.siemens.com/industrialsecurity

)

To stay informed about product updates as they occur, sign up for a product-specific newsletter. You will find more information about this in Product support (https://support.industry.siemens.com/cs/ww/en/ps/15247/pm

)

Introduction

1.2 On the product

SCALANCE X-100 media converter Operating Instructions, 04/2016, C79000-G8976-C346-02

1.2

On the product

What is possible?

The media converters of the SCALANCE X-100 allow the cost-effective installation of Industrial Ethernet linear (bus) and star structures with transitions from one media to another.

The passive use of two identical SCALANCE X-100 media converters in series (cascaded) within a redundant ring is possible. In this case, the media converters behave "like a section of cable". A simple, passive coupling of two rings is also possible. See also "Coupling of network segments (Page 14)".

Note

If devices are supplied over long 24 V power supply lines or networks, measures are necessary to prevent interference by strong electromagnetic pulses on the supply lines. These can result, for example, due to lightning or switching of large inductive load

One of the tests used to attest the immunity of these devices to electromagnetic interference is the "surge immunity test" according to EN 61000

-4-5. This test requires overvoltage

protection for the power supply lines. A suitable device is, for exampl

e, the Dehn Blitzductor

BVT AVD 24 V type no. 918 422 or a comparable protective element.

Manufacturer: DEHN+SÖHNE GmbH+Co.KG Hans Dehn Str.1 Postfach 1640 D

-92306 Neumarkt,

Germany

WARNING

When used in hazardous environments corresponding to Class I, Division 2 or Class I, Zone 2, the device must be installed in a cabinet or a suitable enclosure.

WARNING

To comply with EU Directive 94/9 (ATEX95), this enclosure must meet the requirements of at least IP54 in compliance with EN 60529.

WARNING

EXPLOSION HAZARD

DO NOT CONNECT OR DISCONNECT EQUIPMENT WHEN A FLAMMABLE OR COMBUSTIBLE ATMOSPHERE IS PRESENT.

Introduction

1.2 On the product

SCALANCE X-100 media converter

8 Operating Instructions, 04/2016, C79000-G8976-C346-02

WARNING

Ambient temperature above 55 °C

If a device is operated in an ambient temperature of more than 55 °C, the temperature of the device housing may be higher than 70 °C. The device must therefore be installed so that it is only accessible to service personnel or users that are aware of the reason for restricted access and the required safety measures at an ambient temperature higher than 55 °C.

Scope of delivery

The following components are supplied with a SCALANCE X-100 media converter:

● SCALANCE X-100 media converter

● 2-pin plug-in terminal block (signaling contact)

● 4-terminal plug-in block (power supply)

● Product information

Accessories

Component

Packaging unit

Article number

IE FC Stripping Tool

6GK1 901-1GA00

IE FC blade cassettes

6GK1 901-1GB00

IE FC TP standard cable GP

6XV1 840 2AH10

IE FC TP trailing cable

6XV1 840-3AH10

IE FC TP marine cable

6XV1 840-4AH10

IE FC TP trailing cable GP

6XV1 870-2D

IE FC TP flexible cable GP 1 6XV1 870-2B

IE FC RJ-45 Plug 180

6GK1 901-1BB10-2AA0

IE FC RJ-45 Plug 180

6GK1 901-1BB10-2AB0

IE FC RJ-45 Plug 180

6GK1 901-1BB10-2AE0

Introduction

1.2 On the product

SCALANCE X-100 media converter Operating Instructions, 04/2016, C79000-G8976-C346-02

Unpacking and checking

WARNING

Do not use any parts that show evidence of damage

If you use damaged parts, there is no guarantee that the device will function according to the specification.

If you use damaged parts, this can lead to the following problems:

• Injury to persons

• Loss of the approvals

• Violation of the EMC regulations

• Damage to the device and other components

Use only undamaged parts.

1. Make sure that the package is complete.

2. Check all the parts for transport damage.

Electrostatic discharge

NOTICE

Electrostatic sensitive devices (ESD)

Electronic modules contain electrostatic sensitive components

These components can easily be destroyed if handled incorrectly.

Note the following instructions to avoid damage.

• Touch electronic modules only when you absolutely need to work on them.

• If electronic modules need to be touched, the body of the person involved must first be

electrostatically discharged and grounded.

• Do not bring electronic modules in contact with electrically isolating materials such as plastic film, isolating table top pads or clothing made of synthetic fibers.

• Place the modules only on conductive surfaces.

• Pack, store and transport electronic modules and components only in conductive

packaging such as metalized plastic or metal containers, conductive foam or household aluminum foil.

Introduction

1.2 On the product

SCALANCE X-100 media converter

10 Operating Instructions, 04/2016, C79000-G8976-C346-02

SCALANCE X-100 media converter Operating Instructions, 04/2016, C79000-G8976-C346-02

2.1

Possible network topologies

Switching technology allows extensive networks to be set up with numerous nodes and simplifies network expansion.

Which topologies can be implemented?

Using the media converters of the SCALANCE X-100 product line, you can implement bus and star topologies. It is also possible to link rings and to use two identical media converters in a ring structure. See also "Cascading two media converters (Page 26)".

Note

Keep to the maximum permitted cable lengths of the devices you are

using. You will find the

permitted cable lengths in the section "

Technical specifications (Page 41)".

Bus topology

Figure 2-1 Example of an electrical/optical bus topology with SCALANCE X101-1

Network topologies

2.1 Possible network topologies

SCALANCE X-100 media converter

12 Operating Instructions, 04/2016, C79000-G8976-C346-02

Star topology

The following figure shows an optical star structure with the IE switches X-400 and X106-1. A SCALANCE W access point and SIMATIC NET 200 systems are electrically connected via the media converters SCALANCE X101-1 or SCALANCE X101-1LD.

Figure 2-2 Example of an optical star topology with SCALANCE X101-1 or SCALANCE X101-1LD

Network topologies

2.1 Possible network topologies

SCALANCE X-100 media converter Operating Instructions, 04/2016, C79000-G8976-C346-02

Ring topology

The following figure shows an electrical ring with a SCALANCE X204IRT as redundancy manager and SCALANCE X208 IE switches. Using the media converters SCALANCE X1011 or SCALANCE X101-1LD, there is a conversion to an optical section.

Figure 2-3 Example of an electrical ring with SCALANCE X101-1 or SCALANCE X101-1LD

Network topologies

2.2 Coupling of network segments

SCALANCE X-100 media converter

14 Operating Instructions, 04/2016, C79000-G8976-C346-02

2.2

Coupling of network segments

The example of a coupling between two ring networks using two SCALANCE X101-1 media converters is only indirectly possible via nodes capable of redundancy (e.g. SCALANCE X-

400). This applies to all SCALANCE X-100 media converters.

The following figure shows the standby coupling of two redundant rings using the master/slave concept of the SCALANCE X-400 with SCALANCE X101-1 or SCALANCE X101-1LD media converters.

Figure 2-4 Example of a standby coupling of two redundant rings

SCALANCE X-100 media converter Operating Instructions, 04/2016, C79000-G8976-C346-02

3.1

Overview of the SCALANCE X-100 media converters

Table 3- 1 Overview of the product characteristics

Properties

X101-1

X101-1LD

SIMATIC environment + +

Diagnostics LED

24 VDC + +

2 x 24 VDC + +

Compact housing 40 mm (securing collar, etc.)

Signaling contact + on-site operation

Diagnostics: Web, SNMP, PROFINET

C-PLUG - -

Ring redundancy with RM

Passive ring redundancy

Standby redundancy

IRT capability - -

Fast learning - -

Passive listening

Log table - -

SNTP + SICLOCK

Cut Through + +

Table 3- 2 Overview of the connection options

X101-1

X101-1LD

TP (RJ-45)

Fast Ethernet 10 / 100 Mbps

1 1

Fiber multimode (BFOC)

1300 nm

1 -

Fiber long distance single mode (BFOC) 1310 nm

- 1

Description of the device

3.2 Product characteristics

SCALANCE X-100 media converter

16 Operating Instructions, 04/2016, C79000-G8976-C346-02

3.2

Product characteristics

3.2.1

SCALANCE X101-1

Possible attachments

The SCALANCE X101-1 media converter has an RJ-45 jack and a BFOC socket for connecting end devices or further network segments.

Note

The BFOC socket (Bayonet

Fiber Optic Connector) corresponds to the ST socket.

Figure 3-1 SCALANCE X101-1

+ 37 hidden pages

Siemens SCALANCE X101-1,SCALANCE X101-1LD Operating Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual