Siemens RUGGEDCOM RX5000 Installation Manual

Preface

RUGGEDCOM RX5000

Installation Guide

Introduction

Installing the Device

Modules

Technical Specifications

Dimension Drawings

Certification

1

2

3

4

5

6

06/2017

RC1058-EN-06

RUGGEDCOM RX5000

Installation Guide

Copyright © 2017 Siemens Canada Ltd
All rights reserved. Dissemination or reproduction of this document, or evaluation and communication of its contents, is not authorized

except where expressly permitted. Violations are liable for damages. All rights reserved, particularly for the purposes of patent application or
trademark registration.

This document contains proprietary information, which is protected by copyright. All rights are reserved. No part of this document may be
photocopied, reproduced or translated to another language without the prior written consent of Siemens Canada Ltd.

Disclaimer Of Liability

Siemens has verified the contents of this document against the hardware and/or software described. However, deviations between the product
and the documentation may exist.

Siemens shall not be liable for any errors or omissions contained herein or for consequential damages in connection with the furnishing,
performance, or use of this material.

The information given in this document is reviewed regularly and any necessary corrections will be included in subsequent editions. We
appreciate any suggested improvements. We reserve the right to make technical improvements without notice.

Registered Trademarks

RUGGEDCOM™ and ROS™ are trademarks of Siemens Canada Ltd.
Linux® is the registered trademark of Linus Torvalds in the United States and other countries.
The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a

world-wide basis.
Other designations in this manual might be trademarks whose use by third parties for their own purposes would infringe the rights of the

owner.

Security Information

Siemens provides products and solutions with industrial security functions that support the secure operation of plants, machines, equipment
and/or networks. They are important components in a holistic industrial security concept. With this in mind, Siemens' products and solutions
undergo continuous development. Siemens recommends strongly that you regularly check for product updates.

For the secure operation of Siemens products and solutions, it is necessary to take suitable preventive action (e.g. cell protection concept) and
integrate each component into a holistic, state-of-the-art industrial security concept. Third-party products that may be in use should also be
considered. For more information about industrial security, visit http://www.siemens.com/industrialsecurity.

To stay informed about product updates as they occur, sign up for a product-specific newsletter. For more information, visit http://

support.automation.siemens.com.

Warranty

Siemens warrants this product for a period of five (5) years from the date of purchase, conditional upon the return to factory for maintenance
during the warranty term. This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall render all
warranties null and void. The warranties set forth in this article are exclusive and are in lieu of all other warranties, performance guarantees
and conditions whether written or oral, statutory, express or implied (including all warranties and conditions of merchantability and fitness for
a particular purpose, and all warranties and conditions arising from course of dealing or usage or trade). Correction of nonconformities in the
manner and for the period of time provided above shall constitute the Seller’s sole liability and the Customer’s exclusive remedy for defective
or nonconforming goods or services whether claims of the Customer are based in contract (including fundamental breach), in tort (including
negligence and strict liability) or otherwise.

For warranty details, visit www.siemens.com/ruggedcom or contact a Siemens customer service representative.

Contacting Siemens

Address

Siemens Canada Ltd

Telephone

Toll-free: 1 888 264 0006

E-mail

[e-mail]

ii

RUGGEDCOM RX5000

Installation Guide

Industry Sector
300 Applewood Crescent
Concord, Ontario
Canada, L4K 5C7

Tel: [phone]
Fax: [phone]

Web

www.siemens.com/ruggedcom

iii

RUGGEDCOM RX5000

Installation Guide

iv

RUGGEDCOM RX5000

Installation Guide

Table of Contents

Table of Contents

Preface ............................................................................................................ vii

Alerts ................................................................................................................................................. vii

Related Documents ............................................................................................................................ viii

Accessing Documentation .................................................................................................................. viii

Training ............................................................................................................................................ viii

Customer Support .............................................................................................................................. viii

Chapter 1

Introduction ..................................................................................................... 1

1.1Feature Highlights ........................................................................................................................ 1

1.2Description ................................................................................................................................... 2



Chapter 2

Installing the Device ......................................................................................... 5

2.1General Procedure ........................................................................................................................ 6

2.2Required Tools and Materials ......................................................................................................... 6

2.3Cabling Recommendations ............................................................................................................ 6

2.3.1Protection On Twisted-Pair Data Ports .................................................................................. 7

2.3.2Gigabit Ethernet 1000Base-TX Cabling Recommendations ..................................................... 7

2.4Mounting the Device .................................................................................................................... 8

2.4.1Mounting the Device to a Rack ........................................................................................... 8

2.4.2Mounting the Device to a Panel .......................................................................................... 9

2.5Installing the Chassis Ground Connection ..................................................................................... 10

2.6Grounding the Device ................................................................................................................. 11

2.7Connecting the Failsafe Alarm Relay ............................................................................................. 12

2.8Connecting Power ....................................................................................................................... 12

2.8.1Connecting AC Power ....................................................................................................... 13

2.8.2Connecting DC Power ....................................................................................................... 14

2.9Connecting to the Device ............................................................................................................ 15

2.10Configuring the Device .............................................................................................................. 16

Chapter 3

Modules .......................................................................................................... 17

3.1Available Modules ....................................................................................................................... 18

3.2Installing/Removing Line Modules ................................................................................................ 21

v



Table of Contents

RUGGEDCOM RX5000

Installation Guide

3.3Installing/Removing Power Supply Modules ................................................................................... 24

Chapter 4

Technical Specifications .................................................................................. 27

4.1Failsafe Relay Specifications ......................................................................................................... 27

4.2Operating Environment ............................................................................................................... 27

4.3Mechanical Specifications ............................................................................................................ 28

Chapter 5

Dimension Drawings ....................................................................................... 29

Chapter 6

Certification .................................................................................................... 31

6.1Approvals ................................................................................................................................... 31

6.1.1TÜV SÜD ......................................................................................................................... 31

6.1.2European Commission (EC) ............................................................................................... 32

6.1.3 FCC ................................................................................................................................. 32

6.1.4FDA/CDRH ........................................................................................................................ 32

6.1.5 ISED ................................................................................................................................ 33

6.1.6ACMA .............................................................................................................................. 33

6.1.7 ISO .................................................................................................................................. 33

6.1.8 RoHS ............................................................................................................................... 33

6.1.9Other Approvals ............................................................................................................... 34

6.2EMC and Environmental Type Tests .............................................................................................. 34

vi

RUGGEDCOM RX5000

Installation Guide

Preface

This guide describes the RUGGEDCOM RUGGEDCOM RX5000. It describes the major features of the device,
installation, commissioning and important technical specifications.

It is intended for use by network technical support personnel who are responsible for the installation,
commissioning and maintenance of the device. It is also recommended for use by network and system planners,
system programmers, and line technicians.

CONTENTS

• “Alerts”

• “Related Documents”

• “Accessing Documentation”

• “Training”

• “Customer Support”



Preface

Alerts

The following types of alerts are used when necessary to highlight important information.

DANGER!

DANGER alerts describe imminently hazardous situations that, if not avoided, will result in death or
serious injury.

WARNING!

WARNING alerts describe hazardous situations that, if not avoided, may result in serious injury and/or
equipment damage.

CAUTION!

CAUTION alerts describe hazardous situations that, if not avoided, may result in equipment damage.

IMPORTANT!

IMPORTANT alerts provide important information that should be known before performing a procedure
or step, or using a feature.

NOTE

NOTE alerts provide additional information, such as facts, tips and details.

Alerts vii



Preface

RUGGEDCOM RX5000

Installation Guide

Related Documents

Other documents that may be of interest include:

• RUGGEDCOM ROX II User Guide for the RUGGEDCOM RX5000

• RUGGEDCOM Module Catalog (https://support.industry.siemens.com/cs/ca/en/view/109748479)

Accessing Documentation

The latest user documentation for RUGGEDCOM RX5000 is available online at www.siemens.com/ruggedcom. To
request or inquire about a user document, contact Siemens Customer Support.

Training

Siemens offers a wide range of educational services ranging from in-house training of standard courses on
networking, Ethernet switches and routers, to on-site customized courses tailored to the customer's needs,
experience and application.

Siemens' Educational Services team thrives on providing our customers with the essential practical skills to make
sure users have the right knowledge and expertise to understand the various technologies associated with critical
communications network infrastructure technologies.

Siemens' unique mix of IT/Telecommunications expertise combined with domain knowledge in the utility,
transportation and industrial markets, allows Siemens to provide training specific to the customer's application.

For more information about training services and course availability, visit www.siemens.com/ruggedcom or
contact a Siemens Sales representative.

Customer Support

Customer support is available 24 hours, 7 days a week for all Siemens customers. For technical support or general
information, contact Siemens Customer Support through any of the following methods:

Online

Visit http://www.siemens.com/automation/support-request to submit a Support Request (SR) or check on the status of an
existing SR.

Telephone

Call a local hotline center to submit a Support Request (SR). To locate a local hotline center, visit http://

www.automation.siemens.com/mcms/aspa-db/en/automation-technology/Pages/default.aspx.

Mobile App

Install the Industry Online Support app by Siemens AG on any Android, Apple iOS or Windows mobile device and be able to:

• Access Siemens' extensive library of support documentation, including FAQs and manuals

• Submit SRs or check on the status of an existing SR

• Contact a local Siemens representative from Sales, Technical Support, Training, etc.

• Ask questions or share knowledge with fellow Siemens customers and the support community

viii Related Documents

RUGGEDCOM RX5000

Installation Guide

Introduction

The RUGGEDCOM RUGGEDCOM RX5000 is a high-port density routing and switching platform, designed
to operate in harsh environments.The RUGGEDCOM RX5000 can withstand high levels of electromagnetic
interference, radio frequency interference, and a wide temperature range of -40 to 85 °C (-40 to 185 °F). The
RUGGEDCOM RX5000 is designed to meet the challenging climatic and environmental demands found in utility,
industrial, and military network applications.

The RUGGEDCOM RX5000's superior hardware design, coupled with the embedded RUGGEDCOM RX5000
operating system, provides improved system reliability for the most demanding network applications. The cyber
security and networking features make it ideally suited for creating secure Ethernet networks for mission critical,
real-time, control applications.

The RUGGEDCOM RX5000 is a scalable, modular platform providing the ability to change the configuration as the
network grows and needs change.

This section provides more information about the RUGGEDCOM RX5000.

Chapter 1

Introduction

CONTENTS

• Section1.1, “Feature Highlights”

• Section1.2, “Description”

Section1.1

Feature Highlights

Ethernet Ports

• Up to 96 x 10/100Base-TX copper Ethernet ports

• 2 x 10/100/1000Base-TX copper Ethernet ports

• Up to 48 x 100Base-FX fiber optical Ethernet ports

• Up to 2 x Gigabit Ethernet ports

• Long-haul optics allow distances up to 90 km (56 mi)

• Multiple connector types: ST, MTRJ, LC, SC

Reliability in Harsh Environments

• Immunity to EMI and high voltage electrical transients

• Zero-Packet-Loss Technology

• -40 to 85 °C (-40 to 185 °F) operating temperature (no fans within chassis or modules)

• [Optional] Conformal coated printed circuit boards

Universal Power Supply Options

• Fully integrated, dual-redundant (optional) power supplies

Feature Highlights 1

Chapter 1

4

6

7

8

10

11

4

5

1

2

3

9

12

Introduction

RUGGEDCOM RX5000

Installation Guide

• Universal high voltage ranges: 88-300 VDC or 85-264 VAC

• Terminal blocks for reliable maintenance-free connections

• CSA/UL 60950-1 safety approved to 85 °C (185 °F)

Section1.2

Description

The RUGGEDCOM RX5000 features various ports, controls and indicator LEDs on individual modules and the front
panel for connecting, configuring and troubleshooting the device.

Figure1:RUGGEDCOM RX5000 Modules

1.Control Module 2.Power Supply Module 3.Line Module (Typical) 4.Alarm Indicator LED 5.Lamp Test/Alarm Cut-Off (LT/ACO)

Button 6.Management Ethernet Port 7.Utility USB Port 8.RS232 Serial Console Port (DB9) 9.Failsafe Alarm Relay 10.Compact
Flash Card Port 11.Power Supply Module Indicator LEDs 12.Power Supply Terminal Block

When the RUGGEDCOM RX5000 is configured for rack front mounting, these ports, controls and LEDs are located
on the front panel.

2 Description

RUGGEDCOM RX5000

435 6

1

1

2

Installation Guide

Figure2:Front Panel

1.Power Supply Module Indicator LEDs 2.Alarm Indicator LEDs 3.Utility USB Port 4.Management Ethernet Port 5.Lamp Test/Alarm

Cut-Off (LT/ACO) Button 6.RS232 Serial Console Port (DB9)

Chapter 1

Introduction

Power Supply Module Indicator LEDs Indicate the status of the power modules.

• I = The power supply is receiving power

• O = The power supply is supplying power

Alarm Indicator LED Indicates when an alarm condition exists.

• Green = Alarms cleared/acknowledged

• Red = Alarm

Lamp Test/Alarm Cut-Off (LT/ACO) Button This button performs two functions:

• Press and hold this button to test all indicator LEDs

• Press and release this button to acknowledge an active alarm

Management Port This 10/100Base-T Ethernet port is used for system management that is out-of-band from the

Utility USB Port Use the USB port to upgrade the ROX II software or install files, such as configuration files

Compact Flash Card Port Houses the compact flash card, which contains active and backup installations of ROX II,

RS232 Serial Console Port The serial console port is for interfacing directly with the device and accessing initial

Failsafe Alarm Relay Latches to default state when a power disruption or other alarm condition occurs. For more

switch fabric.

and feature key files. For more information, refer to the RUGGEDCOM ROX II User Guide for
the RUGGEDCOM RX5000.

along with the configuration database and other system data.

management functions. For information about connecting to the device via the serial
console port, refer to Section2.9, “Connecting to the Device”.

information, refer to:

• Section2.7, “Connecting the Failsafe Alarm Relay”

• Section4.1, “Failsafe Relay Specifications”

Power Supply Terminal Block A pluggable terminal block. For more information, refer to Section2.8, “Connecting Power”.

Description 3

Chapter 1

Introduction

RUGGEDCOM RX5000

Installation Guide

4 Description

RUGGEDCOM RX5000

Installation Guide

Installing the Device

Installing the Device

The following sections describe how to install the device, including mounting the device, connecting power, and
connecting the device to the network.

DANGER!

Electrocution hazard – risk of serious personal injury and/or damage to equipment. Before performing
any maintenance tasks, make sure all power to the device has been disconnected and wait
approximately two minutes for any remaining energy to dissipate.

WARNING!

Burn hazard – risk of serious personal injury. Avoid contact with the surface of the unit. The metal
surface may be hot due to the high allowable ambient temperature per specification.

Éviter tout contact avec la surface. La surface métallique peut être chaude a cause d'une température
ambiante élevée selon les spécifications. S.V.P. se référer à la version française de ce guide pour les
détails.

Chapter 2

WARNING!

Radiation hazard – risk of serious personal injury. This product contains a laser system and is classified
as a CLASS 1 LASER PRODUCT. Use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous radiation exposure.

IMPORTANT!

This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall
render all warranties null and void.

Changes or modifications not expressly approved by Siemens Canada Ltd could invalidate
specifications, test results, and agency approvals, and void the user's authority to operate the
equipment.

IMPORTANT!

This product should be installed in a restricted access location where access can only be gained by
authorized personnel who have been informed of the restrictions and any precautions that must be
taken. Access must only be possible through the use of a tool, lock and key, or other means of security,
and controlled by the authority responsible for the location.

CONTENTS

• Section2.1, “General Procedure”

• Section2.2, “Required Tools and Materials”

• Section2.3, “Cabling Recommendations”

• Section2.4, “Mounting the Device”

• Section2.5, “Installing the Chassis Ground Connection”

5

Chapter 2

Installing the Device

• Section2.6, “Grounding the Device”

• Section2.7, “Connecting the Failsafe Alarm Relay”

• Section2.8, “Connecting Power”

• Section2.9, “Connecting to the Device”

• Section2.10, “Configuring the Device”

Section2.1

RUGGEDCOM RX5000

Installation Guide

General Procedure

The general procedure for installing the device is as follows:

1. Review the relevant certification information for any regulatory requirements. For more information, refer to

Section6.1, “Approvals”.

2. Review the RUGGEDCOM RX5000 Modules Catalog for special installation or regulatory requirements related
to the modules installed in the device.

3. Mount the device.

4. Connect the failsafe alarm relay.

5. Connect power to the device and ground the device to safety Earth.

6. Connect the device to the network.

7. Configure the device.

Section2.2

Required Tools and Materials

The following tools and materials are required to install the RUGGEDCOM RX5000:

Tools/Materials Purpose

AC or DC power cord (16 AWG) For connecting power to the device.

CAT-5 Ethernet cables For connecting the device to the network.

Phillips screwdriver For mounting the device to a panel.

4 x #8-32 screws For mounting the device to a panel.

Section2.3

Cabling Recommendations

Before connecting the device, be aware of the recommendations and considerations outlined in this section.

CONTENTS

• Section2.3.1, “Protection On Twisted-Pair Data Ports”

6 General Procedure

RUGGEDCOM RX5000

Installation Guide

Installing the Device

• Section2.3.2, “Gigabit Ethernet 1000Base-TX Cabling Recommendations”

Section2.3.1

Protection On Twisted-Pair Data Ports

All copper Ethernet ports on RUGGEDCOM products include transient suppression circuitry to protect against
damage from electrical transients and conform with IEC 61850-3 and IEEE 1613 Class 1 standards. This means
that during a transient electrical event, communications errors or interruptions may occur, but recovery is
automatic.

Siemens also does not recommend using copper Ethernet ports to interface with devices in the field across
distances that could produce high levels of ground potential rise (i.e. greater than 2500 V), during line-to-ground
fault conditions.

Section2.3.2

Gigabit Ethernet 1000Base-TX Cabling Recommendations

The IEEE 802.3ab Gigabit Ethernet standard defines 1000 Mbit/s Ethernet communications over distances of up
to 100 m (328 ft) using all 4 pairs in category 5 (or higher) balanced, unshielded twisted-pair cabling. For wiring
guidelines, system designers and integrators should refer to the Telecommunications Industry Association (TIA)
TIA/EIA-568-A wiring standard that characterizes minimum cabling performance specifications required for proper
Gigabit Ethernet operation. For reliable, error-free data communication, new and pre-existing communication
paths should be verified for TIA/EIA-568-A compliance.

The following table summarizes the relevant cabling standards:

Chapter 2

Cabling Category

< 5 No New wiring infrastructure required.

5 Yes Verify TIA/EIA-568-A compliance.

5e Yes No action required. New installations should be designed with Category 5e or higher.

6 Yes No action required.

> 6 Yes Connector and wiring standards to be determined.

1000Base-

TX Compliant

Required Action

Follow these recommendations for copper data cabling in high electrical noise environments:

• Data cable lengths should be as short as possible, preferably 3 m (10 ft) in length. Copper data cables should
not be used for inter-building communications.

• Power and data cables should not be run in parallel for long distances, and should be installed in separate
conduits. Power and data cables should intersect at 90° angles when necessary to reduce inductive coupling.

• Shielded/screened cabling can be used when required. Care should be taken to avoid the creation of ground
loops with shielded cabling.

Protection On Twisted-Pair Data Ports 7

Chapter 2

Installing the Device

Section2.4

Mounting the Device

The RUGGEDCOM RX5000 is designed for maximum mounting and display flexibility. It can be equipped with
adapters that allow it to be installed in a 48 cm (19 in) rack or directly on a panel.

IMPORTANT!

Heat generated by the device is channeled outwards to the enclosure. As such, it is recommended that

2.5 cm (1 in) of space be maintained on all open sides of the device to allow for some convectional
airflow.

Forced airflow is not required. However, any increase in airflow will result in a reduction of ambient
temperature and improve the long-term reliability of all equipment mounted in the rack space.

NOTE

For detailed dimensions of the device with mounting hardware installed, refer to Chapter5, Dimension

Drawings.

CONTENTS

• Section2.4.1, “Mounting the Device to a Rack”

RUGGEDCOM RX5000

Installation Guide

• Section2.4.2, “Mounting the Device to a Panel”

Section2.4.1

Mounting the Device to a Rack

For installations, the RUGGEDCOM RX5000 can be equipped with adapters pre-installed at the front or rear of
the chassis. Additional adapters are provided to further secure the device in high-vibration or seismically active
locations.

To secure the device to a standard 48 cm (19 in) rack, do the following:

1. Make sure the adapters are installed on the correct side of the chassis.

• To make the modules and ports accessible, install the adapters at the rear of the chassis

• To make the management ports and LEDs accessible, install the adapters at the front of the chassis

NOTE

The chassis features multiple mounting holes, allowing the adapters to be installed up to 25 mm
(1 in) from the face of the device.

8 Mounting the Device

RUGGEDCOM RX5000

1

2

3

1

2

3

Installation Guide

Installing the Device

Chapter 2

Figure3:Adapters

1.Rear 2.Front 3.Adapter

2. If required, install adapters on the opposite side of the device to protect from vibrations.

3. Insert the device into the rack.

NOTE

4. Secure the adapters to the rack using the supplied hardware.

Section2.4.2

Since heat within the device is channeled to the enclosure, it is recommended that 1 rack-unit
of space, or 44 mm (1.75 in), be kept empty above the device. This allows a small amount of
convectional airflow.

Forced airflow is not required. However, any increase in airflow will result in a reduction of
ambient temperature and improve the long-term reliability of all equipment mounted in the rack
space.

Mounting the Device to a Panel

For panel installations, the RUGGEDCOM RX5000 can be equipped with adapters pre-installed on each side of the
chassis. The adapters allow the device to be attached to a panel using screws.

To mount the device to a panel, do the following:

Mounting the Device to a Panel 9

Chapter 2

1

2

2

Installing the Device

1. Place the device against the panel and align the adapters with the mounting holes.

RUGGEDCOM RX5000

Installation Guide

Figure4:Panel Mounting

1.Screw 2.Adapter

2. Install the supplied screws to secure the adapters to the panel. Make sure the screws are torqued to 2 ± 0.1
N·m (18 ± 1 lbf-in)

Section2.5

Installing the Chassis Ground Connection

If the ground terminal on the power supply module(s) is not connected to safety Earth, a connection must be
provided from the chassis ground terminal on the RUGGEDCOM MX5000 chassis.

IMPORTANT!

If the ground terminal on the power supply module(s) is connected to safety Earth, a connection from
the chassis ground terminal is not required.

1. Position the grounding cable and external tooth lock washer on the RUGGEDCOM MX5000.

10 Installing the Chassis Ground Connection

RUGGEDCOM RX5000

3

2

1

Installation Guide

Installing the Device

Chapter 2

Figure5:Chassis Ground Cable Assembly

1.External Tooth Lock Washer 2.#8-32×5/16" Pan Head Screw 3.Grounding Cable

2. Secure the grounding cable and external tooth lock washer to the RUGGEDCOM MX5000 with one pan head
screw. Torque the screw to 3.4 N·m (30 lbf·in).

NOTE

The other end of the grounding cable will be connected to the inside of the enclosure in later
steps.

Section2.6

Grounding the Device

Connect the chassis ground terminal to protective Earth if neither of the power supplies are already connected.
If the ground terminal on the power supply module(s) is not connected to safety Earth, a connection must be

provided from the chassis ground terminal.

IMPORTANT!

If the ground terminal on the power supply module(s) is connected to safety Earth, a connection from
the chassis ground terminal is not required.

The RUGGEDCOM RX5000 chassis ground terminal uses a #8-32 screw. It is recommended to terminate the
ground connection with a #8 ring lug and torque it to 3.4 N·m (30 lbf·in).

Grounding the Device 11

Chapter 2

2

1

21 3

Installing the Device

Figure6:Chassis Ground Connection

1.#8-32 Screw 2.#8 Ring Lug

Section2.7

Connecting the Failsafe Alarm Relay

RUGGEDCOM RX5000

Installation Guide

The failsafe relay on the Control Module (CM) can be configured to latch based on alarm conditions. The NO
(Normally Open) contact is closed when the unit is powered and there are no active alarms. If the device is not
powered or if an active alarm is configured, the relay opens the NO contact and closes the NC (Normally Closed)
contact.

Pin Function

NC Normally Closed

Common Ground

NO Normally Open

Figure7:Failsafe Alarm Relay Wiring

1.Normally Open 2.Common (Ground) 3.Normally Closed

Section2.8

Connecting Power

The RUGGEDCOM RX5000 supports dual redundant AC and/or DC power modules that can be installed in any
combination.

The RUGGEDCOM RX5000 is equipped with a screw-type terminal block, which provides power to both power
modules. The terminal block is installed using Philips screws and compression plates, allowing either bare wire

12 Connecting the Failsafe Alarm Relay

RUGGEDCOM RX5000

Installation Guide

Installing the Device

connections or crimped terminal lugs. Use #6 size ring lugs for secure, reliable connections under severe shock or
vibration.

For information about installing or removing a power module, refer to Section3.3, “Installing/Removing Power

Supply Modules”.

DANGER!

Electrocution hazard – risk of serious personal injury or death. The device may have two power
modules equipped, which may be connected to separate power sources. Make sure all power sources
are off before servicing the power module terminals.

IMPORTANT!

• In an AC/DC power arrangement, the placement of the AC and DC power modules is not slot­dependent. Either power module slot can be used for AC or DC power.

• For maximum redundancy in a dual power module configuration, use two independent power
sources.

• Use only #16 gage copper wiring when connecting terminal blocks.

• For 125/230 VAC rated equipment, an appropriately rated AC circuit breaker must be installed.

• For 125/250 VDC rated equipment, an appropriately rated DC circuit breaker must be installed.

• It is recommended to provide a separate circuit breaker for each power module module.

• Equipment must be installed according to applicable local wiring codes and standards.

Chapter 2

CONTENTS

• Section2.8.1, “Connecting AC Power”

• Section2.8.2, “Connecting DC Power”

Section2.8.1

Connecting AC Power

To connect AC power to the device, do the following:

DANGER!

Electrocution hazard – risk of death, serious personal injury and/or damage to the device. Make sure
the supplied cover is always installed over high voltage screw-type terminal blocks.

CAUTION!

Electrical hazard – risk of damage to equipment. Do not connect AC power cables to a DC power supply
terminal block. Damage to the power supply may occur.

NOTE

The terminal block is installed using Philips screws and compression plates, allowing either bare wire
connections or crimped terminal lugs. Use #6 size ring lugs for secure, reliable screws, which must be
removed to make connections.

1. Connect the positive wire from the power source to the live terminal on the terminal block.

Connecting AC Power 13

Chapter 2

1

2

3

Installing the Device

Figure8:AC Terminal Block Wiring

1.Live Terminal 2.Ground Terminal 3.Neutral Terminal

RUGGEDCOM RX5000

Installation Guide

2. Connect the negative wire from the power source to the neutral terminal on the terminal block.

IMPORTANT!

If the ground terminals are not connected to safety Earth, the chassis ground connection must be
connected. For more information, refer to Section2.6, “Grounding the Device”.

3. Using a braided wire or other appropriate grounding wire, connect the ground terminal to the chassis ground
connection. The ground terminal is used as the ground conductor for all surge and transient suppression
circuitry internal to the unit.

4. Connect the ground terminal on the power source to the ground terminal on the device. For more
information, refer to Section2.6, “Grounding the Device”.

Section2.8.2

Connecting DC Power

To connect DC power to the device, do the following:

NOTE

The terminal block is installed using Philips screws and compression plates, allowing either bare wire
connections or crimped terminal lugs. Use #6 size ring lugs for secure, reliable screws, which must be
removed to make connections.

1. Connect the positive wire from the power source to the positive terminal on the terminal block.

14 Connecting DC Power

RUGGEDCOM RX5000

1

2

3

Installation Guide

Figure9:DC Terminal Block Wiring

1.Live Terminal 2.Ground Terminal 3.Neutral Terminal

Installing the Device

2. Connect the negative wire from the power source to the neutral terminal on the terminal block.

IMPORTANT!

If the ground terminals are not connected to safety Earth, the chassis ground connection must be
connected. For more information, refer to Section2.6, “Grounding the Device”.

3. Using a braided wire or other appropriate grounding wire, connect the ground terminal to the chassis ground
connection. The ground terminal is used as the ground conductor for all surge and transient suppression
circuitry internal to the unit.

4. Connect the ground terminal on the power source to the ground terminal on the device. For more
information, refer to Section2.6, “Grounding the Device”.

Chapter 2

Section2.9

Connecting to the Device

The following describes the various methods for accessing the RUGGEDCOM ROX II console and Web interfaces
on the device. For more detailed instructions, refer to the RUGGEDCOM ROX II User Guide for the RUGGEDCOM
RX5000.

Serial Console and Management Ports

Connect a PC or terminal directly to the serial console or management ports to access the boot-time control and
ROX II interfaces. The serial console port provides access to ROX II's console interface, while the management port
provides access to ROX II's console and Web interfaces.

IMPORTANT!

The serial console and management (MGMT) ports are intended to be used only as temporary
connections during initial configuration or troubleshooting.

The serial console port implements RS232 DCE (Data Communication Equipment) on a DB9 connector. The
following is the pin-out for the port:

Connecting to the Device 15

Chapter 2

1

15

69

1

8

Installing the Device

RUGGEDCOM RX5000

Installation Guide

Pin Name Description

1 DCD Data Carrier Detect

2 RX Receive Data

3 TX Transmit Data

4 DTR Data Terminal Ready

5 GND Signal Ground

6 DSR Data Set Ready

Figure10:Serial DB9 Console Port

7 RTS Request to Send

8 CTS Clear To Send

9 Reserved (Do Not Connect)

The management port is a 10/100Base-TX copper Ethernet port with an RJ45 connector. The following is the pin­out for the management port:

Pin Name Description

1 TX+ Transmit Data+

2 TX- Transmit Data-

3 RX+ Receive Data+

Figure11:RJ45 Management Port

4 Reserved (Do Not Connect)

5 Reserved (Do Not Connect)

6 RX- Receive Data-

7 Reserved (Do Not Connect)

8 Reserved (Do Not Connect)

Communication Ports

Connect any of the available Ethernet ports on the device to a management switch and access the RUGGEDCOM
ROX II console and Web interfaces via the device's IP address. The factory default IP address for the RUGGEDCOM
RX5000 is https://192.168.0.2.

For more information about available ports, refer to Chapter3, Modules.

Section2.10

Configuring the Device

Once the device is installed and connected to the network, it must be configured. All configuration management
is done via the RUGGEDCOM ROX II interface. For more information about configuring the device, refer to the
RUGGEDCOM ROX II User Guide associated with the installed software release.

16 Configuring the Device

RUGGEDCOM RX5000

2

3

4

6 7 8 9

1

5

10

Installation Guide

Modules

The RUGGEDCOM RX5000 features slots for up to two power modules and eight line modules, which can be
used to expand and customize the capabilities of the device to suit specific applications. A variety of modules
are available, each featuring a specific type of communication port: copper Ethernet, fiber optic Ethernet, SFP or
serial.

Two slots are reserved for one control module (required) and one switch module (optional).
All modules are field-replaceable.
Use the RUGGEDCOM ROX II software to determine which ports are equipped on the device. For more information,

refer to the RUGGEDCOM ROX II User Guide for the device.

NOTE

Switch modules are only compatible with 8-port fiber optic Ethernet modules.

Chapter 3

Modules

Figure12:Available Chassis Slots

1.Power Supply Module (PS1) 2.Ethernet Module Slot (LM1) 3.Ethernet Module Slot (LM2) 4.Ethernet Module Slot (LM3) 5.Control
Module (CM) 6.Switch Module (SM) 7.Ethernet Module Slot (LM4) 8.Ethernet Module Slot (LM5) 9.Ethernet Module Slot (LM6)

10.Power Supply Module (PS2)

CONTENTS

• Section3.1, “Available Modules”

• Section3.2, “Installing/Removing Line Modules”

• Section3.3, “Installing/Removing Power Supply Modules”

17

Chapter 3

Modules

Section3.1

Available Modules

The following is a list of all power and line modules available for use in the RUGGEDCOM RX5000. For
more information about individual modules, refer to the RUGGEDCOM RX5000 Modules Catalog [https://
support.industry.siemens.com/cs/ca/en/view/109748479].

Power Supply Modules

RUGGEDCOM RX5000

Installation Guide

RUGGEDCOM RX5000PN PS HI Specifications

Input Range: 88 to 300 VDC or
85 to 264 VAC

Terminal Type: Screw

Copper Ethernet Modules

RUGGEDCOM RX5000PN LM 16TX01 Specifications

Ports: 16
Speed: 10/100Base-TX
Port Type: RJ45
Distance: 100 m (328 ft)

RUGGEDCOM RX5000PN LM 4CG01 Specifications

Ports: 4
Speed: 10/100/1000Base-TX
Port Type: RJ45
Distance: 100 m (328 ft)

Article Numbers

6GK6050-0AL13-0AA0
(Standard)

6GK6050-0AL13-0AA1
(Conformal Coated)

Article Numbers

6GK6050-0AL20-0NB0
(Standard)

6GK6050-0AL20-0NB1
(Conformal Coated)

Article Numbers

6GK6050-0AL20-0FC0
(Standard)

6GK6050-0AL20-0FC1
(Conformal Coated)

Fiber Optic Ethernet Modules

RUGGEDCOM RX5000PN LM 8FX01 Specifications

RUGGEDCOM RX5000PN LM 8FX11 Specifications

18 Available Modules

Mode: MM
Speed: 100Base-FX
Ports: 8
Port Type: ST
Distance: 2 km (1.2 mi)

Mode: MM
Speed: 100Base-FX
Ports: 8
Port Type: LC
Distance: 2 km (1.2 mi)

Article Numbers

6GK6050-0AL20-0BB0
(Standard)

6GK6050-0AL20-0BB1
(Conformal Coated)

Article Numbers

6GK6050-0AL20-0BD0
(Standard)

6GK6050-0AL20-0BD1
(Conformal Coated)

RUGGEDCOM RX5000

Installation Guide

Chapter 3

Modules

RUGGEDCOM RX5000PN LM 8FX50 Specifications

Speed: 100Base-FX
SFP Sockets: 8

RUGGEDCOM RX5000PN LM 4FG50 Specifications

Speed: 1000Base-LX
SFP Sockets: 4

Serial Modules

RUGGEDCOM RX5000PN LM S01 Specifications

Speed: RS232/RS422/RS485
Ports: 8
Port Type: DB9

Article Numbers

6GK6050-0AL20-0CU0
(Standard)

6GK6050-0AL20-0CU1
(Conformal Coated)

Article Numbers

6GK6050-0AL20-0JB0 (Standard)
6GK6050-0AL20-0JB1

(Conformal Coated)

Article Numbers

6GK6050-0AL20-0KB0
(Standard)

6GK6050-0AL20-0KB1
(Conformal Coated)

Control Modules

RUGGEDCOM RX5000PN CM01 L2SE Specifications

Layer 2 Standard Edition

RUGGEDCOM RX5000PN CM01 L3SEL3HW Specifications

Layer 3 Standard Edition, Layer 3
hardware

RUGGEDCOM RX5000PN CM01 L3SECL3HW Specifications

Layer 3 Security Edition, Layer 3
Hardware

Article Numbers

6GK6050-0AL30-0AA0
6GK6050-0AL30-0AA1

Article Numbers

6GK6050-0AL30-0BA0
6GK6050-0AL30-0BA1

Article Numbers

6GK6050-0AL30-0CA0
6GK6050-0AL30-0CA1

Available Modules 19

Chapter 3

Modules

RUGGEDCOM RX5000

Installation Guide

RUGGEDCOM RX5000PN CM01 L3SEL2HW Specifications

Layer 3 Standard Edition, Layer 2
Hardware

RUGGEDCOM RX5000PN CM01 L3SECL2HW Specifications

Layer 3 Security Edition, Layer 2
Hardware

Switch Modules

RUGGEDCOM RX5000PN SM02 Specifications

Ports: 2
Speed: 10/100/1000Base-TX
Port Type: RJ45
Distance: 100 m (328.1 ft)

Article Numbers

6GK6050-0AL30-0DA0
6GK6050-0AL30-0DA1

Article Numbers

6GK6050-0AL30-0EA0
6GK6050-0AL30-0EA1

Article Numbers

6GK6050-0AL40-0BA0
(Standard)

6GK6050-0AL40-0BA1
(Conformal Coated)

RUGGEDCOM RX5000PN SM09 Specifications

Speed: 1000Base-LX
SFP Sockets: 2

RUGGEDCOM RX5000PN SM32 Specifications

Ports: 2
Speed: 10/100/1000Base-TX
Port Type: RJ45
Distance: 100 m (328.1 ft)

RUGGEDCOM RX5000PN SM34 Specifications

Mode: MM
Speed: 1000Base-SX
Wavelength: 850 nm
Ports: 2
Port Type: LC
Distance: 500 m (1640 ft)

RUGGEDCOM RX5000PN SM39 Specifications

Speed: 1000Base-LX
SFP Sockets: 2

Article Numbers

6GK6050-0AL40-0JA0 (Standard)
6GK6050-0AL40-0JA1

(Conformal Coated)

Article Numbers

6GK6050-0AL40-0MA0
(Standard)

6GK6050-0AL40-0MA1
(Conformal Coated)

Article Numbers

6GK6050-0AL40-0PA0
(Standard)

6GK6050-0AL40-0PA1
(Conformal Coated)

Article Numbers

6GK6050-0AL40-0UA0
(Standard)

6GK6050-0AL40-0UA1
(Conformal Coated)

20 Available Modules

RUGGEDCOM RX5000

Installation Guide

Chapter 3

Modules

RUGGEDCOM RX5000PN SM61 Specifications

Layer 3/88 Gigabit Throughput,
no uplink ports

RUGGEDCOM RX5000PN SM69 Specifications

Layer 3/88 Gigabit Throughput,
2x 10G SFP + Slots Blank

Blank Modules

RUGGEDCOM RX5000PN PS XX Specifications

—

Article Numbers

6GK6050-0AL40-0VA0
(Standard)

6GK6050-0AL40-0VA1
(Conformal Coated)

Article Numbers

6GK6050-0AL40-0WA0
(Standard)

6GK6050-0AL40-0WA1
(Conformal Coated)

Article Numbers

6GK6050-0AL10-0AA0

RUGGEDCOM RX5000PN LM Blank Specifications

—

Article Numbers

6GK6050-0AL20-0AA0

Section3.2

Installing/Removing Line Modules

Upon installing a new line module in the device, all features associated with the module are available in
RUGGEDCOM ROX II. For more information, refer to the RUGGEDCOM ROX II User Guide for the RUGGEDCOM
RX5000.

Once a line module is removed, all the features associated with the module are hidden or disabled in RUGGEDCOM
ROX II.

Installing/Removing Line Modules 21

Chapter 3

1

2

3

5 6 7 8

4

Modules

Figure13:Line Modules

1.Ethernet Module Slot (LM1) 2.Ethernet Module Slot (LM2) 3.Ethernet Module Slot (LM3) 4.Control Module (CM) 5.Switch
Module (SM) 6.Ethernet Module Slot (LM4) 7.Ethernet Module Slot (LM5) 8.Ethernet Module Slot (LM6)

CAUTION!

Contamination hazard – risk of equipment damage. Prevent the ingress of water, dirts and other debris
that may lead to premature equipment failure. Always make sure slots are not left empty and open
ports are protected with plugs or covers.

RUGGEDCOM RX5000

Installation Guide

Removing a Line Module

To remove a line module, do the following:

1. Make sure power to the device has been disconnected and wait approximately two minutes for any remaining
energy to dissipate.

2. [Optional] If the device is installed in a rack, remove it from the rack.

3. Loosen the screws that secure the module.

4. Pull the module from the chassis to disconnect it.

22 Installing/Removing Line Modules

RUGGEDCOM RX5000

1

2

3

Installation Guide

Figure14:Removing a Module

1.Chassis 2.Module 3.Screw

Chapter 3

Modules

5. Install a new module or a blank module (to prevent the ingress of dust and dirt).

6. [Optional] If necessary, install the device in the rack.

7. Connect power to the device.

Installing a Line Module

To install a line module, do the following:

1. Make sure power to the device has been disconnected and wait approximately two minutes for any remaining
energy to dissipate.

2. [Optional] If the device is installed in a rack, remove it from the rack.

3. Remove the current module from the slot.

4. Insert the new module into the slot.

Installing/Removing Line Modules 23

Chapter 3

1

2

3

1

2

3

5 6 7 8

4

Modules

RUGGEDCOM RX5000

Installation Guide

Figure15:Installing a Module

1.Chassis 2.Module 3.Screw

5. Tighten the screws to secure the module.

6. [Optional] If necessary, install the device in the rack.

7. Connect power to the device.

Section3.3

Installing/Removing Power Supply Modules

The RUGGEDCOM RX5000 supports dual redundant AC and/or DC power supplies that can be installed in any
combination.

Figure16:Power Supply Modules

1.Power Supply Module (PS1) 2.Power Supply Module (PS2)

24 Installing/Removing Power Supply Modules

RUGGEDCOM RX5000

3

2

1

Installation Guide

CAUTION!

Contamination hazard – risk of equipment damage. Prevent the ingress of water, dirts and other debris
that may lead to premature equipment failure. Always make sure slots are not left empty.

NOTE

Power modules are hot swappable. When installing/removing a power module, it is not necessary to
turn off power to the redundant power module.

Removing a Power Supply Module

To remove a power module, do the following:

1. Loosen the screws that secure the module to the chassis until the module can be removed.

2. Slide the module out of the chassis.

Chapter 3

Modules

Figure17:Removing a Power Supply

1.Screws 2.Power Supply 3.Chassis

DANGER!

Electrocution hazard – risk of serious personal injury or death. Make sure power to the module is
turned off before servicing the power supply terminal.

3. Turn off power to the module.

4. Disconnect the power supply wiring from the terminal block. Alternatively, for convenience, remove the
terminal block with the wiring still connected and set it aside to be connected later to the new module.

5. Install a new or blank module to prevent the ingress of dust and dirt.

Installing a Power Supply Module

To install a power module, do the following:

1. If equipped, remove the existing module.

Installing/Removing Power Supply Modules 25

Chapter 3

3

2

1

Modules

2. If applicable, connect the supplied terminal block to the module or connect the terminal block from the
previous module.

3. Confirm or connect the wiring from the power supply to the module. For more information, refer to

Section2.8, “Connecting Power”.

4. Insert the module into the empty slot.

RUGGEDCOM RX5000

Installation Guide

Figure18:Installing a Power Supply Module

1.Screws 2.Power Supply 3.Chassis

5. Hand-tighten the screws to secure the power module to the chassis.

6. Turn on power to the module and confirm the module is receiving and supplying power. This is indicated by
the LEDs on the module.

LED State Description

O Green The module is supplying power

I Green The module is receiving power

26 Installing/Removing Power Supply Modules

RUGGEDCOM RX5000

Installation Guide

Technical Specifications

This section provides important technical specifications related to the device and available modules.

CONTENTS

• Section4.1, “Failsafe Relay Specifications”

• Section4.2, “Operating Environment”

• Section4.3, “Mechanical Specifications”

Section4.1

Technical Specifications

Chapter 4

Failsafe Relay Specifications

Maximum Switching Voltage Rated Switching Current Isolation

30 VDC 2 A, 60 W

125 VDC 0.24 A, 30 W

125 VAC 0.5 A, 62.5 W

220 VDC 0.24 A, 60 W

250 VAC 0.25 A, 62.5 W

Section4.2

Operating Environment

Parameter Range Comments

Ambient Operating Temperature -40 to 85 °C

(-40 to 185 °F)

Ambient Relative Humidity 5% to 95% Non-condensing

Ambient Storage Temperature -40 to 85 °C

(-40 to 185 °F)

Measured from a 30 cm (12 in) radius surrounding the center of the enclosure.

1500 V

for 1 minute

rms

Failsafe Relay Specifications 27

Chapter 4

Technical Specifications

Section4.3

Mechanical Specifications

Dimensions Refer to Chapter5, Dimension Drawings.

Weight 14-16 kg (30-35 lbs)

Ingress Protection IP40

Chassis Material Aluminum

RUGGEDCOM RX5000

Installation Guide

28 Mechanical Specifications

RUGGEDCOM RX5000

441.7

446.8

469.6

479.8

221.5

311.9

5.8

16.0

31.8

10.9

25.4

177.8

175.3

16.0

12.7

101.6

117.6

133.4

Installation Guide

Dimension Drawings

Dimension Drawings

Chapter 5

NOTE

All dimensions are in millimeters, unless otherwise stated.

Figure19:Overall Dimensions

29

Chapter 5

Dimension Drawings

RUGGEDCOM RX5000

Installation Guide

30

RUGGEDCOM RX5000

Installation Guide

Certification

The RUGGEDCOM RX5000 device has been thoroughly tested to guarantee its conformance with recognized
standards and has received approval from recognized regulatory agencies.

CONTENTS

• Section6.1, “Approvals”

• Section6.2, “EMC and Environmental Type Tests”

Section6.1

Approvals

Chapter 6

Certification

The following sections detail the approvals issued for the RUGGEDCOM RX5000.

CONTENTS

• Section6.1.1, “TÜV SÜD”

• Section6.1.2, “European Commission (EC)”

• Section6.1.3, “FCC”

• Section6.1.4, “FDA/CDRH”

• Section6.1.5, “ISED”

• Section6.1.6, “ACMA”

• Section6.1.7, “ISO”

• Section6.1.8, “RoHS”

• Section6.1.9, “Other Approvals”

Section6.1.1

TÜV SÜD

This device is certified by TÜV SÜD to meet the requirements of the following standards:

• CAN/CSA-C22.2 NO. 60950-1-07 (R2012)

Information Technology Equipment – Safety – Part 1: General Requirements (Bi-National standard, with UL
60950-1)

• UL 60950-1

Information Technology Equipment – Safety – Part 1: General Requirements)

Approvals 31

Chapter 6

Certification

Section6.1.2

RUGGEDCOM RX5000

Installation Guide

European Commission (EC)

This device is declared by Siemens Canada Ltd to comply with essential requirements and other relevant provisions
of the following EC directives:

• EN 60950-1

Information Technology Equipment – Safety – Part 1: General Requirements

• EN 61000-6-2

Electromagnetic Compatibility (EMC) – Part 6-2: Generic Standards – Immunity for Industrial Environments

• EN 60825-1

Safety of Laser Products – Equipment Classification and Requirements

• EN 55022

Information Technology Equipment – Radio disturbance characteristics – Limits and methods of measurement

• EN 50581

Technical Documentation for the Assessment of Electrical and Electronic Products with Respect to the Restriction
of Hazardous Substances

The device is marked with a CE marking and can be used throughout the European community.

A copy of the CE Declaration of Conformity is available from Siemens Canada Ltd. For contact information, refer to

“Contacting Siemens”.

Section6.1.3

FCC

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference in which case the user will be required
to correct the interference on his own expense.

Section6.1.4

FDA/CDRH

This device meets the requirements of the following U.S. Food and Drug Administration (FDA) standard:

• Title 21 Code of Federal Regulations (CFR) – Chapter I – Sub-chapter J – Radiological Health

32 European Commission (EC)

RUGGEDCOM RX5000

Installation Guide

Section6.1.5

ISED

This device is declared by Siemens Canada Ltd to meet the requirements of the following ISED (Innovation Science
and Economic Development Canada) standard:

• CAN ICES-3 (A)/NMB-3 (A)

Section6.1.6

ACMA

This device meets the requirements of the following Australian Communications and Media Authority (ACMA)
standards under certificate ABN 98 004 347 880:

• Radiocommunications (Compliance Labelling – Devices) Notice 2014 made under Section 182 of the
Radiocommunications Act 1992

• Radiocommunications Labelling (Electromagnetic Compatibility) Notice 2008 made under Section 182 of the
Radiocommunications Act 1992

• Radiocommunications (Compliance Labelling – Electromagnetic Radiation) Notice 2003 made under Section
182 of the Radiocommunications Act 1992

• Telecommunications Labelling (Customer Equipment and Customer Cabling) Notice 2001 made under Section
407 of the Telecommunication Act 1997

The device is marked with an RCM symbol to indicate compliance when sold in the Australian region.

Chapter 6

Certification

A copy of the Declaration of Conformity is available via Siemens Industry Online Support at https://

support.industry.siemens.com/cs/ww/en/view/89855782.

Section6.1.7

ISO

This device was designed and manufactured using a certified ISO (International Organization for Standardization)
quality program that adheres to the following standard:

• ISO 9001:2008
Quality management systems – Requirements

Section6.1.8

RoHS

This device is declared by Siemens Canada Ltd to meet the requirements of the following RoHS (Restriction of
Hazardous Substances) directives for the restricted use of certain hazardous substances in electrical and electronic
equipment:

ISED 33

Chapter 6

Certification

• China RoHS 2

Administrative Measure on the Control of Pollution Caused by Electronic Information Products

A copy of the Material Declaration is available online at https://support.industry.siemens.com/cs/ww/en/

view/109738831.

Section6.1.9

Other Approvals

This device meets the requirements of the following additional standards:

• IEEE 1613

IEEE Standard Environmental and Testing Requirements for Communications Networking Devices in Electric
Power Substations

• IEC 61850-3

Communications Networks and Systems for Power Utility Automation – Part 3: General Requirements

• IEC 61000-6-2

Electromagnetic Compatibility (EMC) – Part 6-2: Generic Standards – Immunity for Industrial Environments

RUGGEDCOM RX5000

Installation Guide

Section6.2

EMC and Environmental Type Tests

The RUGGEDCOM RX5000 has passed the following EMC and environmental tests.

IEC 61850-3 EMC Type Tests

Test Description Test Levels

IEC 61000-4-2 ESD

IEC 61000-4-3 Radiated RFI Enclosure Ports 20 V/m Note

IEC 61000-4-4 Burst (Fast Transient)

IEC 61000-4-5 Surge

Enclosure Contact +/- 8 kV 4

Enclosure Air +/- 15 kV 4

Signal ports +/- 4 kV @ 2.5 kHz Note

DC Power ports +/- 4 kV 4

AC Power ports +/- 4 kV 4

Earth ground ports +/- 4 kV 4

Signal ports

DC Power ports

+/- 4 kV line-to-earth,

+/- 2 kV line-to-line

+/- 2 kV line-to-earth,

+/- 1 kV line-to-line

Severity

Levels

a

a

4

3

IEC 61000-4-6 Induced (Conducted) RFI

34 Other Approvals

AC Power ports

Signal ports 10 V 3

D.C Power ports 10V 3

+/- 4 kV line-to-earth,

+/- 2 kV line-to-line

4

RUGGEDCOM RX5000

Installation Guide

Chapter 6

Certification

Test Description Test Levels

AC Power ports 10V 3

Earth ground ports 10V 3

IEC 61000-4-8 Magnetic Field Enclosure Ports

IEC 61000-4-29 Voltage Dips & Interrupts

IEC 61000-4-11 Voltage Dips & Interrupts AC Power ports

IEC 61000-4-12 Damped Oscillatory

IEC 61000-4-16 Mains Frequency Voltage

DC Power ports

AC Power ports 30% for 1 period, 60% for 50 periods

Signal ports

DC Power ports

AC Power ports

Signal ports 30 V Continuous, 300 V for 1 s 4

DC Power ports 30 V Continuous, 300 V for 1 s 4

1000 A/m for 1 s 5

30% for 0.1 s, 60% for

0.1 s, 100% for 0.05 s

100% for 5 periods,

100% for 50 periods

2.5 kV common, 1 kV

differential mode @1 MHz

2.5 kV common, 1 kV

differential mode @1MHz

2.5 kV common, 1 kV

differential mode @1MHz

Severity

Levels

100 A/m

3

3

3

IEC 61000-4-17 Ripple on DC Power Supply DC Power ports 10% 3

Signal ports 2 kV (Fail-Safe Relay output)

DC Power ports 2 kVDielectric Strength

IEC 60255-5

a

Siemens-specified severity levels

HV Impulse

AC Power ports 2 kV

Signal ports 5 kV (Fail-Safe Relay output)

DC Power ports 5 kV

AC Power ports 5 kV

IEEE 1613 EMC Type Tests

NOTE

The RUGGEDCOM RX5000 meets Class 2 requirements for an all-fiber configuration and Class 1
requirements for copper ports.

Description Test Levels

Enclosure Contact +/-2 kV, +/-4 kV, +/- 8 kVESD

Enclosure Air +/-4 kV, +/-8 kV, +/-15 kV

Radiated RFI Enclosure ports 35 V/m

EMC and Environmental Type Tests 35

Signal ports +/- 4 kV @ 2.5 kHzFast Transient

DC Power ports +/- 4 kV

Chapter 6

Certification

RUGGEDCOM RX5000

Installation Guide

Description Test Levels

AC Power ports +/- 4 kV

Earth ground ports +/- 4 kV

Oscillatory

HV Impulse

Dielectric Strength

Signal ports 2.5 kV common mode @1 MHz

DC Power ports 2.5 kV common, 1 kV differential mode @ 1 MHz

AC Power ports 2.5 kV common, 1 kV differential mode @ 1 MHz

Signal ports 5 kV (Fail-Safe Relay output)

DC Power ports 5 kV

AC Power ports 5 kV

Signal ports 2 kV

DC Power ports 2 kV

AC Power ports 2 kV

Environmental Type Tests

Test Description Test Levels

IEC 60068-2-1 Cold Temperature Test Ad -40 °C (-40 °F), 16 Hours

IEC 60068-2-2 Dry Heat Test Bd 85 °C (185 °F), 16 Hours

IEC 60068-2-30 Humidity (Damp Heat, Cyclic) Test Db 95% (non-condensing), 55 °C (131 °F), 6 cycles

IEC 60255-21-1 Vibration 2 g @ 10 - 150 Hz

IEC 60255-21-2 Shock 30 g @ 11 mS

36 EMC and Environmental Type Tests