Siemens RB500 Installation Manual
Siemens AG
Card reader
RB500
Installation Guide
1 2 3
65
98
4
7
B0
A
RB500 EM
Book Contents
English ..........................................................3
Svenska .......................................................19
Document nr: 82336-7
Edition: 04.2010
RB500 Installation Guide 3
ENG
English
Data and design subject to change without notice.
Supply subject to availability.
© 2010 Copyright by Siemens AG
We reserve all rights in this document and in the subject thereof. By
acceptance of the document the recipient acknowledges these rights and
undertakes not to publish the document nor the subject thereof in full or in
part, nor to make them available to any third party without our prior express
written authorization, nor to use it for any purpose other than for which it
was delivered to him.
4 RB500 Installation Guide
ENG
Contents
General ........................................................ 5
Important! .............................................................................. 5
About this document ............................................................ 5
Safety ........................................................... 6
Standards & guidelines.............................. 6
Power supply .............................................. 8
Cable recommendations ............................ 8
Technical data ............................................. 9
Reading distances ................................................................ 9
General features ....................................... 10
Power Up ............................................................................. 10
Programming Mode ............................................................ 10
Timeout Period .................................................................... 10
Exit Programming Mode ..................................................... 10
Preset Congurations (short commands) ........................ 11
Installation ................................................. 12
Mechanical ........................................................................... 12
Outdoor use ......................................................................... 12
Wiring ........................................................ 14
2010 E2V Connections ....................................................... 16
2010 E2V terminal blocks ................................................... 17
RB500 Installation Guide 5
ENG
General
The RB500 can be connected to the system
product Bewator 2010 Omnis. The RB500 can be
ordered in two different variants supporting two
different reading technologies:
• Cotag technology (both active & passive)
• EM4102 technology
Important!
For proper use, this card reader needs that the
Bewator 2010 Omnis reader-node E2V has a
rmware version 4.012, or higher.
About this document
This document only serves as a Installation Guide
when using the RB500 with the main factory setting and only the “short commands”.
6 RB500 Installation Guide
ENG
Safety
• Read the general safety precautions before
operating the device.
• Follow all warnings and instructions marked
on the device.
• Keep this document for reference.
• Always pass this document on together with
the product.
• The device has been approved for use in the
European Union. In countries outside the EU,
the local conditions and regulations need to be
checked before putting the device into service.
• Please also take into account any additional
country-specic, local safety standards or
regulations concerning project planning, operation and disposal of the product.
• Maintenance work must only be carried out by
trained specialists.
Standards & guidelines
This product complies with the requirements of the
European Directives.
The EU declaration of conformity is available from:
Siemens AG
Siemensalle 84
D-76187 Karlsruhe
RB500 Installation Guide 7
ENG
European Directive 1999/5/EC on Radio Equipment and Telecommunications Terminal Equipment (R&TTE):
Compliance with the European Directive 1999/5/
EC has been proven by testing according to the
following standards:
EN 300 330-2 V1.3.1: 2006-04
EN 301 489-3 V1-4-1:2002-08
European Directive 2004/108/EC on Electromagnetic Compatibility (EMC):
Compliance with the European Directive
2004/108/EC has been proven by testing according to the following standards:
EN 50130-4:1995 + A1:1998 + A2:2003
European Directive 2006/95/EC on Low-Voltage
Directive (Safety):
Compliance with the European Directive 2006/95/
EC has been proven by testing according to the
following standard:
EN 60950-1:2006
8 RB500 Installation Guide
ENG
Power supply
Any power supply connected to the RB500 must
conform to CE regulations regarding safety and
EMC.
This includes conformity to SELV (Safety Extra
Low Voltage) according to EN 60950-1.
The supply line fuse shall, independent of host
system, not in any case exceed 10A.
Cable recommendations
The cables between node and reader shall not
exceed 30 m.
RB500 Installation Guide 9
ENG
Technical data
Power supply: 12 -24 V DC
Min. 10,5 V DC
Max. 35V DC
Power consumption RB500-EM:
24V DC: Typ 17 mA (408 mW), Max*): 31 mA (744 mW)
12V DC: Typ 32 mA (384 mW), Max*): 68 mA (816 mW)
*) While horn sounds
Power consumption RB500-Cotag:
24V DC: Typ 23 mA (552 mW), Max*): 40 mA (960 mW)
12V DC: Typ 44 mA (528 mW), Max*): 90 mA (1080 mW)
*) While horn sounds
Frequency range: EM: 125 kHz.
Cotag: 66-132 kHz.
IP Class: IP54
Temperature range: -30° C to +50° C
Dimensions (HxWxD) mm: 140x80x40
If needed, complete the installation with ush mounting
kit BB3.
Reading distances
EM4102 (passive): up to 5 cm
Cotag (passive): up to 5 cm
Cotag (active): up to 10 cm
10 RB500 Installation Guide
ENG
General features
Power Up
Power up will give a rising tone from the Buzzer/
Horn. The factory setting gives that Clock&Data
conguration is selected and will work for the
Bewator 2010 Omnis. See also Preset Congura-
tion (short codes)
Programming Mode
Programming mode is enabled when powering
up the reader with the ‘B’ button pressed for 2
seconds. This is indicated by red and green LEDs
blinking.
Timeout Period
When the reader is in programming mode if no
cards are presented to the reader or short code
keys pressed the reader will automatically time out
and return to normal operation after 60 seconds.
Exit Programming Mode
Programming mode can be cancelled by pressing ‘B’ when red and green LEDs are ashing
together.
RB500 Installation Guide 11
ENG
Preset Congurations (short commands)
At factory the mode Clock&Data is precongured.
In programming mode, you can ensure the con-
guration by using short codes. After selecting the
pre-dened conguration the reader will return to
programming mode.
1. Press “A” and the “3”
Command Function
A3 Precongured interface Clock &
Data. Used for 2010.
The Precongured interface is stored in nonvolatile memory.
A3 Precongured is the interface Clock & Data,
with external control of Red LED, Green LED and
Horn. Also, the yellow LED is not active at all,
showing no indication of noise or key presses.
Loading...