Siemens Metro 21 M216KASPC , SIMATIC ET 200S Operator's Manual

SIMATIC ET 200S distributed I/O Power module PM-E DC24..48V/AC24..230V (6ES7138-4CB11-0AB0)

_

_____________

_

_____________

_

_____________

_

_____________

Preface

Properties

1

Parameters

2

Diagnostics

3

Configuring

4

SIMATIC

ET 200S distributed I/O
Power module PM-E
DC24..48V/AC24..230V
(6ES7138-4CB11-0AB0)

Manual

04/2007

A5E01120024-01

Safety Guidelines

Safety Guidelines

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.

CAUTION
without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.

NOTICE
indicates that an unintended result or situation can occur if the corresponding information is not taken into

account.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.

Qualified Personnel

The device/system may only be set up and used in conjunction with this documentation. Commissioning and
operation of a device/system may only be performed by qualified personnel. Within the context of the safety notes
in this documentation qualified persons are defined as persons who are authorized to commission, ground and
label devices, systems and circuits in accordance with established safety practices and standards.

Prescribed Usage

Note the following:

WARNING

This device may only be used for the applications described in the catalog or the technical description and only
in connection with devices or components from other manufacturers which have been approved or
recommended by Siemens. Correct, reliable operation of the product requires proper transport, storage,
positioning and assembly as well as careful operation and maintenance.

Trademarks

All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this
publication may be trademarks whose use by third parties for their own purposes could violate the rights of the
owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

Siemens AG

Automation and Drives
Postfach 48 48
90327 NÜRNBERG
GERMANY

Ordernumber: A5E01120024-01
Ⓟ 12/2007

Copyright © Siemens AG 2007.
Technical data subject to change

Power module PM-E DC24..48V/AC24..230V (6ES7138-4CB11-0AB0)
Manual, 04/2007, A5E01120024-01

3

Preface

Preface

Purpose of the manual

This manual supplements the

ET 200S Distributed I/O System

Operating Instructions.

General functions for the ET 200S are described in the

ET 200S Distributed I/O System

Operating Instructions.
The information in this document along with the operating instructions enables you to

commission the ET 200S.

Basic knowledge requirements

To understand these operating instructions you should have general knowledge of
automation engineering.

Scope of the manual

This manual applies to this ET 200S module. It describes the components that are valid at
the time of publication.

Recycling and disposal

Thanks to the fact that it is low in contaminants, this ET 200S module is recyclable.
For environmentally compliant recycling and disposal of your electronic waste, please
contact a company certified for the disposal of electronic waste.

Additional support

If you have any questions relating to the products described in these operating instructions,
and do not find the answers in this document, please contact your local Siemens
representative.

http://www.siemens.com/automation/partner
The portal to our technical documentation for the various SIMATIC products and systems is

available at:
http://www.siemens.com/automation/simatic/portal
The online catalog and ordering system are available at:

http://www.siemens.com/automation/mall

Preface

Power module PM-E DC24..48V/AC24..230V (6ES7138-4CB11-0AB0)

4 Manual, 04/2007, A5E01120024-01

Training center

We offer courses to help you get started with the ET 200S and the SIMATIC S7 automation
system. Please contact your regional training center or the central training center in
D -90327, Nuremberg, Germany.
Phone: [phone].

http://www.siemens.com/sitrain

Technical Support

You can reach technical support for all A&D projects

● using the support request web form:
http://www.siemens.com/automation/support-request

● Phone: + 49 180 5050 222

● Fax: + 49 180 5050 223

For more information about our technical support, refer to our Web site at
http://www.siemens.de/automation/service

Service & Support on the Internet

In addition to our documentation services, you can also make use of our comprehensive
online knowledge base on the Internet.

http://www.siemens.com/automation/service&support
There you will find:

● Our Newsletter, which constantly provides you with the latest information about your
products.

● The right documentation for you using our Service & Support search engine.

● The bulletin board, a worldwide knowledge exchange for users and experts.

● Your local contact for Automation & Drives in our contact database.

● Information about on-site services, repairs, spare parts. Lots more can be found on our
"Services" pages.

Power module PM-E DC24..48V/AC24..230V (6ES7138-4CB11-0AB0)
Manual, 04/2007, A5E01120024-01

5

Table of contents

Preface ...................................................................................................................................................... 3

1 Properties ..................................................................................................................................................

7

1.1 Power module PM-E DC24..48V/AC24..230V (6ES7138-4CB11-0AB0) ......................................

7

2 Parameters..............................................................................................................................................

11

3 Diagnostics..............................................................................................................................................

13

3.1 Diagnostics using LED display.....................................................................................................

13

3.2 Error types....................................................................................................................................

14

4 Configuring ..............................................................................................................................................

15

4.1 Configuring the address space ....................................................................................................

15

Index........................................................................................................................................................

17

Table of contents

Power module PM-E DC24..48V/AC24..230V (6ES7138-4CB11-0AB0)

6 Manual, 04/2007, A5E01120024-01

Power module PM-E DC24..48V/AC24..230V (6ES7138-4CB11-0AB0)
Manual, 04/2007, A5E01120024-01

7

Properties

1

1.1 Power module PM-E DC24..48V/AC24..230V (6ES7138-4CB11-0AB0)

Properties

The power module PM-E DC24V..48V/AC24..230V

● Monitors the supply voltage for all the electronic modules in the voltage group. The

supply voltage is fed in by means of the TM-P terminal module.

● Can be used universally and can be assigned parameters for DC and AC load voltage for

use with any electronic module.

● Is required at least once for the ET 200S (to the right of the interface module).

Exception: Design of the ET 200S with an IM151-1 COMPACT

● Control interface (PIQ) and feedback interface (PII) in the process image for option

handling.

● The current status of the power module is stored in the status byte in the process input

image (PII). This is updated irrespective of whether the "No Load Voltage" diagnosis has
been enabled.

● Is additionally equipped with a replaceable fuse (5 mm x 20 mm).

Replacing the fuse:

1

2

① Screwdriver with 3 mm blade
② Fuse

Properties

1.1 Power module PM-E DC24..48V/AC24..230V (6ES7138-4CB11-0AB0)

Power module PM-E DC24..48V/AC24..230V (6ES7138-4CB11-0AB0)

8 Manual, 04/2007, A5E01120024-01

Maximum configuration per voltage group

The number of modules that can be connected depends on the total current of all modules in
a voltage group. This total must not exceed the maximum current carrying capacity.

Address space of inputs/outputs

Address space of inputs/outputs by selecting the following as an option:

Options Address space of the inputs Address space of the outputs
Status byte (S) 1 byte -­Option handling (O) 8 bytes 8 bytes
Status byte and option handling (SO) 9-byte inputs 9 bytes (9th byte not relevant)

General terminal assignment

Note
Terminals A4 and A8 are only available at specified terminal modules.

Terminal assignment PM-E DC24..48V/AC24..230V (6ES7138-4CB11-0AB0)
Terminal Assignment Terminal Assignment Notes
2 L+/L1 6 L+/L1
3 M/ N 7 M/ N
A4 AUX1 A8 AUX1

• L+/L1: Rated load voltage 24 VDC to 48 VDC

• M: Chassis ground

• N: Neutral conductor

• AUX1: Protective-conductor terminal or potential bus (freely usable

up to 230 VAC)

Properties

1.1 Power module PM-E DC24..48V/AC24..230V (6ES7138-4CB11-0AB0)

Power module PM-E DC24..48V/AC24..230V (6ES7138-4CB11-0AB0)
Manual, 04/2007, A5E01120024-01

9

Usable terminal modules

Terminal modules that can be used for PM-E DC24..48V/AC24..230V (6ES7138-4CB11-0AB0)

TM-P15C23-A1
(6ES7193­4CC30-0AA0)

TM-P15C23-A0
(6ES7193-4CD30­0AA0)

TM-P15C22-01
(6ES7193-4CE10­0AA0)

Spring terminal

TM-P15S23-A1
(6ES7193­4CC20-0AA0)

TM-P15S23-A0
(6ES7193-4CD20­0AA0)

TM-P15S22-01
(6ES7193-4CE00­0AA0)

Screw-type terminal

TM-P15N23-A1
(6ES7193­4CC70-0AA0)

TM-P15N23-A0
(6ES7193-4CD70­0AA0)

TM-P15N22-01
(6ES7193-4CE60­0AA0)

Fast Connect

$8;

 

$$













$$

$8;

$8;

$8;

 

$$













$$





$8;

a

$&

9'&

b9'&WRb9'&/ b9'&WRb9'&/

01

3($8;

01

3($8;

:LULQJH[DPSOHV

Block diagram

01

3







3

)6*

3:5

9'&/

%DFNSODQHEXV

(76

EDFNSODQH

EXV

FLUFXLW

)XVH

PRQLWRULQJ

/RDG

YROWDJH

PRQLWRULQJ

)XVHV

Figure 1-1 Block diagram of the PM-E DC24..48V/AC24..230V

Properties

1.1 Power module PM-E DC24..48V/AC24..230V (6ES7138-4CB11-0AB0)

Power module PM-E DC24..48V/AC24..230V (6ES7138-4CB11-0AB0)

10 Manual, 04/2007, A5E01120024-01

Technical data PM-E DC24..48V/AC24..230V (6ES7138-4CB11-0AB0)

Dimensions and weight
Dimension B (mm) 15
Weight 34 g

Voltages, currents, potentials

Rated load voltage 24 VDC to 56.7 VDC

24 V to 48 V / 120 V / 230 V AC

• Overvoltage protection

Yes
Protection with automatic circuit breakers Yes, tripping characteristic B, C
Max. current-carrying capacity 10 A

• For 24 to 56.7 VDC

Up to 30°C: Max. 10 A

Up to 40°C: Max. 9 A

Up to 60°C: Max. 7 A

• For 24 to 48/120/230 VAC

Up to 30°C: Max. 8 A

Up to 40°C: Max. 7 A

Up to 60°C: Max. 5 A

• Short-circuit protection

Yes, IEC 127-2/1, 250 V, 10 A,

fast fuse (5 x 20 mm), replaceable1
Electrical isolation

• Between rated load voltage and backplane

bus

Yes

• Between the power modules

Yes
Insulation test voltage 1500 VAC
Current consumption from backplane bus Max. 9.5 mA

• From load voltage L1/L+ (no load)

Max. 9 mA
Power dissipation of the module Max. 5 W
Parameter length 3 bytes

Status, interrupts, diagnostics

Diagnostic function Yes

• Group error

Red "SF" LED

• Load voltage monitoring

Green "PWR" LED

• Fuse

Green LED "FSG"

• Diagnostic information can be displayed

Yes

1

The fuses (order number: 6ES7193-4KA10-0AA0) for this module are only intended to serve as
supplementary fuses. External overcurrent protection (suitable for branch circuits in accordance with
the electrical engineering regulations that apply to your country) is required for the supply lines of the
load circuit.

Power module PM-E DC24..48V/AC24..230V (6ES7138-4CB11-0AB0)
Manual, 04/2007, A5E01120024-01

11

Parameters

2

Parameters

The following table lists the power module parameters.

Table 2-1 Parameters for power modules

PM-E DC24..48V/

AC24..230V 1

Range of values Default setting Applicability

Diagnostics: No load voltage Disable/enable Disable Power module
Diagnostics: Fuse blown Disable/enable Disable Power module
Voltage type DC/AC DC Power module

1

The power module PM-E DC24..48V/AC24..230V (6ES7138-4CB11-0AB0) is not a direct replacement for the device with
order number 6ES7138-4CB00-0AB0 for AC applications, because the supply voltage must be set to either AC or DC. In
the case of DC applications, the new module does act as a direct replacement because the default setting of the new
parameter is "DC". If you want to replace the device with order number 6ES7138-4CB00-0AB0 in AC applications, you
have to create a new hardware configuration and set the value "AC" in the "Voltage type" parameter.

The parameters are explained below.

Diagnostics: No load voltage

Use this parameter to enable a diagnostic message because there is no load voltage.
If there is no load voltage, only the diagnostic message of the affected power module is sent

to the DP master. The SF error LEDs of all modules in the relevant voltage group light up.

Diagnostics: Fuse blown

Use this parameter to enable a diagnostic message because of a blown fuse.
If a fuse has blown, only the diagnostic message of the affected power module is sent to the

DP master. The SF error LEDs of all modules in the relevant voltage group light up.

Voltage type

Use this parameter to select the load voltage that is connected to the power module: Direct
(DC) voltage or alternating (AC) voltage.

This enables the correct diagnostics to be obtained when the load voltage fails or a fuse
blows.

Parameters

Power module PM-E DC24..48V/AC24..230V (6ES7138-4CB11-0AB0)

12 Manual, 04/2007, A5E01120024-01

Power module PM-E DC24..48V/AC24..230V (6ES7138-4CB11-0AB0)
Manual, 04/2007, A5E01120024-01

13

Diagnostics

3

3.1 Diagnostics using LED display

Power module

LED displays on the power module:

1

2

3

6)

)6*3:5

① Batch error (red)
② Load voltage (green)
③ Fuse (green)

Status and error displays by means of LEDs on power modules

The table below shows the status and error displays on the power module.

Event (LEDs)

SF PWR FSG

Cause Remedy

On No parameter assignment or incorrect

module plugged in. A diagnostic message is
pending.

Check the parameter assignment.
Evaluate the diagnostics.

Off There is no load voltage at the power

module.

Check the load voltage.

Off The fuse in the power module has tripped. Replace the fuse.

Diagnostics

3.2 Error types

Power module PM-E DC24..48V/AC24..230V (6ES7138-4CB11-0AB0)

14 Manual, 04/2007, A5E01120024-01

3.2 Error types

Power module error types

The diagnostic message is reported on channel 0 and applies to the entire module.
The table below shows the types of errors affecting power modules

Table 3-1 Power module error types

Error type Meaning Remedy

17D 10001: Encoder or load

voltage missing

Supply voltage not present
or too low.

Correct the process wiring. Check
the supply voltage.

18D 10010: Fuse is defective The fuse in the power

module has tripped.

Replace the fuse.

Power module PM-E DC24..48V/AC24..230V (6ES7138-4CB11-0AB0)
Manual, 04/2007, A5E01120024-01

15

Configuring

4

4.1 Configuring the address space

Address area for option handling and status byte

You can control and monitor option handling, and evaluate the status byte of the power
module using the control (PIO) and feedback interface (PII).

The address range of the control (PIO) and feedback interface (PII) depends on how the
corresponding entry in the configuration software is configured, or which entry has been
selected.

This table shows the PII feedback interface and the PIO control interface for different entries.

Table 4-1 PII feedback interface and PIO control interface

With STEP 7, HW Config

or COM PROFIBUS

or other configuration

software

PII feedback interface PIO control interface

Usual entry for the power
module

--- ---

Ends in ...S IBx Status byte --­Ends in ...O IBx

:::
IBx+7

Option handling

QBx
:::
QBx+7

Option handling

IBx
:::
IBx+7

Option handling

QBx
:::
QBx+7

Option handling

Ends in ...SO

IBx+8 Status byte QBx+8 Not applicable

Configuring

4.1 Configuring the address space

Power module PM-E DC24..48V/AC24..230V (6ES7138-4CB11-0AB0)

16 Manual, 04/2007, A5E01120024-01

Status byte for power modules

(%[





/RDGYROWDJHPLVVLQJ
/RDGYROWDJHSUHVHQW

'LDJQRVWLFELWVRIWKHSRZHUPRGXOHV

(QFRGHURUORDGYROWDJHPLVVLQJ
SUHVHQWIRUDOO30(SRZHUPRGXOHV

)XVHLVGHIHFWLYH

%LWQR

Figure 4-1 Assignment of status byte for power modules

Power module PM-E DC24..48V/AC24..230V (6ES7138-4CB11-0AB0)
Manual, 04/2007, A5E01120024-01

17

Index

B

Basic knowledge requirements, 3
Block diagram,

9

D

Disposal, 3

I

Internet

Service & Support,

4

M

Maximum configuration, 8

P

Parameters

For power modules,

11

Power modules,

13

Error types,

14

Parameters,

11

Properties,

7

R

Recycling, 3

S

Scope

Manual,

3

Service & Support,

4

T

Technical data, 10
Technical Support,

4

Terminal assignment,

8

Training center,

4

Index

Power module PM-E DC24..48V/AC24..230V (6ES7138-4CB11-0AB0)

18 Manual, 04/2007, A5E01120024-01