Page 1
KION
Service Manual – Addendum 1999-11-15
MTS-99-0011
Page 2
KION Service Manual – Addendum 1999-11-15
Contents
Spare parts ................................................................ 3
External connections/MIB Output port...................... 3
Calibration of MGM................................................... 3
D
UOVIEW – ISD software installation .......................... 4
Internal battery .......................................................... 4
Battery capacity indication......................................... 4
Troubleshooting ........................................................ 5
Maintenance.............................................................. 5
MTS-99-0011
Siemens-Elema AB
2
Page 3
KION Service Manual – Addendum 1999-11-15
Spare parts
For information regarding spare parts, please refer to
the KION Spare Parts List, Order No. 63 08 956 E392E.
As the assortment of spare parts is being revised as
the development of the product proceeds, revisions
to the above referenced spare parts list was published
in the July 29, 1999 EM EXPRESS titled ”LSS – Spare
Parts News”.
Additionally, the PC 1730 Control with CON-SW
V012.04 or lower is no longer available as spare part.
The new version (V012.05) of this board is part of the
mandatory ”KION Update 1999-09”-kit, which is to be
installed in all units ASAP. For further information,
see Update Instructions (UI) EM007/99/S.
Should this PC-board need to be replaced on a unit
that has not yet been subject to the aforesaid update,
the only possible solution is to perform the update.
The above referenced EM EXPRESS as well as the
Update Instructions (UI's) are available on the
TD Intranet Information Server.
External
connectionslabel
MIB2 MIB1 MIB1 MIB2
Incorrect version Correct version
External connections-label
External connections / MIB Output ports
A label indicating the function of the external connection ports is attached close to these ports. Due to a
printing error, the two MIB ports have been transposed
on older versions of this label.
Correct information is that:
• The port to the left is MIB1.
• The port to the right is MIB2.
Please note that the output data from these two ports
is identical. Thus the MIB Connector can be connected
to any one of the MIB ports.
The only way for a user to notice this error is to open
the ”Component log” in the KION Display. Equipment
connected to MIB1 (according to the misprinted label)
will be correctly indicated as connected to MIB2 in
the ”Component log”.
External connection labels with this printing error will
be replaced as a corrective action included in Update
1999-09.
MTS-99-0011
Calibration of MGM
A new version of the Calibration Instructions for
MULTIGAS and MULTIGAS + Modules is under
production. This will soon be published on the
TD Intranet Information Server.
Siemens-Elema AB
3
Page 4
KION Service Manual – Addendum 1999-11-15
DUOVIEW – ISD software installation
Download cable To COM1 on the PC
The version of installed ISD software is shown on the
DUOVIEW during the start-up sequence.
A PC with 3.5" floppy drive must be used when
updating the ISD software. The illustration shows how
to connect the download cable (55 96 502 E537U).
The ISD software in the DUOVIEW must be of the
same version as the KION Display-software.
DUOVIEW – ISD software installation setup
Internal battery
Internal batteries are not supplied as spare parts,
batteries must be purchased locally. A list of approved
batteries can be found in the KION – Service Manual
and on a label inside the battery drawer.
Please note that the VARTA Type accu-CF battery,
stated in the list of recommended batteries, is no
longer produced.
Battery capacity indication
The actual capacity of the internal battery is continously shown on the KION display by means of a
battery voltage bargraph. A fully charged battery is
thus indicated as ”100%” .
An internal battery discharge / recharge process will
automatically start e. g. when the KION System is
reconnected to mains power supply.
• During the discharge sequence (approx. 20 min),
the bargraph will show ”100%”.
• During the recharge sequence that follows (approx.
60 min), the bargraph will start at approx. ”50%”
and rise to ”100%”.
This is a normal function of the KION System and is
not an indication of battery error.
MTS-99-0011
Siemens-Elema AB
4
Page 5
KION Service Manual – Addendum 1999-11-15
Troubleshooting
The text below is a revised version of Recommended
actions if the ”Checking bellows level detector” test
fails. It replaces the corresponding text on page 5-13
in the KION – Service Manual, 1st English edition.
• Clean the bellows container and the ”window” on
the bellows position sensor.
• Check the bellows position sensor function
(KION System in Standby and the bellows in bottom
position):
– Connect a voltmeter between connector P46/Pin
C9 on PC 1750 Transducer and GND.
– If the voltmeter shows 0 V; replace PC 1750
Transducer.
– If the voltmeter shows +5 V:
– Cover the bellows position sensor ”window”
with a piece of white paper and check that the
voltage showed on the voltmeter drops to 0 V
or if possible
– Run the KION System and check that the voltage
showed on the voltmeter toggles between +5 V
(bellows in a lower position) and 0 V (bellows in
top position).
– If the voltage remains +5 V (constant) during
this test;
1. Replace PC 1750 Transducer
2. Replace PC 1766 Bellows position sensor
3. Replace the cable connecting PC 1766 /
PC 1733.
• Redo the ”Checking flow transducers” test after
each action.
• If the test is successfully passed, the fault was
located.
• If the test still fails, contact Siemens-Elema,
Technical Service Support.
MTS-99-0011
Maintenance
A limited number of early KION Systems was not
equipped with gas inlet filters in the Gas Distribution
Block and the design of this Block does not permit
subsequent fitting of filters in the gas inlet channels.
Thus, the ”I. Gas inlet filters“ included in the
”Maintenance kit 12 months for Kion” cannot be
used on these early KION Systems.
Siemens-Elema AB
5
Loading...