Siemens IP-Module, IP-Module CFVA-IP, IP-Module CVVA-IP User Manual
IP-Module
IP-Module CFVA-IP
IP-Module CVVA-IP
User manual
Issue 07/2005
Fire Safety & Security Products
Siemens Building Technologies
Equipment availability and technical specifications subject to change without notice.
Data and design subject to change without notice. Supply subject to availability.
© Copyright by
Siemens Building Technologies AG
Wir behalten uns alle Rechte an diesem Dokument und an dem in ihm dargestellten Gegenstand vor. Der Empfänger anerkennt diese
Rechte und wird dieses Dokument nicht ohne unsere vorgängige schriftliche Ermächtigung ganz oder teilweise Dritten zugänglich machen
oder außerhalb des Zweckes verwenden, zu dem es ihm übergeben worden ist.
We reserve all rights in this document and in the subject thereof. By acceptance of the document the recipient acknowledges these rights
and undertakes not to publish the document nor the subject thereof in full or in part, nor to make them available to any third party without our
prior express written authorization, nor to use it for any purpose other than for which it was delivered to him.
3
Siemens Building Technologies
Contents
1 Introduction .............................................................................................5
2 General Safety Precautions ...................................................................6
3 Ordering data...........................................................................................7
3.1 Ordering data for IP-Module CFVA-IP ......................................................7
3.2 Ordering data for IP-Module CVVA-IP......................................................7
4 Norms and Directives .............................................................................8
5 Technical data .........................................................................................9
5.1 Technical data for IP-Module CFVA-IP.....................................................9
5.2 Technical data for IP-Module CVVA-IP ..................................................10
6 Installing the IP-Module........................................................................11
6.1 Installing IP-Module type CFVA-IP .........................................................11
6.2 Installing IP-Module type CVVA-IP .........................................................12
7 Establishing initial communication with the device..........................14
7.1 Changing the IP address of the client PC...............................................14
7.2 Mapping a network route ........................................................................14
8 Checking device accessibility .............................................................16
9 Device homepage .................................................................................17
9.1 Calling up the device homepage.............................................................17
9.1.1 Calling up the device homepage using Microsoft Internet Explorer .......17
9.1.2 Calling up the device homepage using the Web-Cam IP Manager........17
9.2 Components of the device homepage ....................................................19
10 Configuring network settings .............................................................. 20
10.1 Changing the device IP address.............................................................21
9.1.1. Changing the device IP address via the device homepage....................21
9.1.2 Changing the IP address using the Web-Cam IP Manager....................22
11 Configuring image parameters............................................................ 24
11.1 Configuring general image parameters ..................................................24
11.2 Configuring text overlay ..........................................................................24
11.3 Configuring JPEG encoder settings........................................................ 25
12 Setting the date and time .....................................................................27
13 Configuring user names and passwords ...........................................28
14 Restarting the IP Module......................................................................29
15 Live video...............................................................................................31
15.1 Displaying live video ...............................................................................31
15.2 Setting live video resolution ....................................................................32
15.3 Storing still pictures.................................................................................32
16 Establishing access to the device via internet ..................................33
17 Embedding live video images in a dedicated HTML page................35
18 Service mode......................................................................................... 36
19 Index.......................................................................................................37
Fire Safety & Security Products
Introduction
1 Introduction
Thank you for deciding to buy this IP-Module.
We wish you every success in using this product. If you have any questions about
the product, please contact your local SIEMENS branch office.
This IP-Module allows you to display live video images from a dome camera on
your PC via an internet connection.
The live video images are transmitted via a TCP/IP based network and displayed
using an http browser (e.g. Netscape 7.0, Mozilla or Internet Explorer).
The image parameters and network settings of the dome camera can be
configured via the network.
About this manual
This user manual explains how to install and configure the IP-Module. Please read
the manual carefully to familiarize yourself with the device.
5
Siemens Building Technologies
Fire Safety & Security Products
General Safety Precautions
2 General Safety Precautions
Read these instructions carefully before connecting the camera and the IP-
Module in order to avoid damage caused by improper installation or use.
Installation may be done only by authorized personnel according to the local
safety regulations.
Operate the camera and the IP-Module only with the designated voltage.
Follow the safety instructions for the camera and for the IP-Module.
Never use the camera and the IP-Module for purposes other than those
designated.
Repairs and adjustments to the camera and the IP-Module may be done only by
authorized personnel.
If liquids or objects get into the housing, disconnect the camera and the IP-
Module from the power supply and have it checked by your authorized dealer
before using it again. (Danger of electric shock!)
This equipment has been tested and found to comply with the limits for a Class
B digital device. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment may generate, uses and can radiate radio frequency energy
and, if not installed and used according to instructions, may cause harmful
interference with radio communications.
Be aware that any modifications not explicitly approved in this manual may void
your equipment warranty.
The shielded interface cable recommended in this manual must be used with
this equipment in order to comply with the limits for a digital output device.
6
Siemens Building Technologies
Fire Safety & Security Products
Ordering data
3 Ordering data
3.1 Ordering data for IP-Module CFVA-IP
Type Item no. Description Weight
CFVA-IP 2GF1086-8AL IP-Module for 12 V DC / 24
V DC indoor fix dome
camera
0.40 kg
Extra accessories, not included in the standard
supply!
PSU230-12 2GF1800-8BE 12 V DC camera power
supply
0.12 kg
CAPA2410-P230 2GF1800-8BJ 24 V AC camera power
supply
0.30 kg
3.2 Ordering data for IP-Module CVVA-IP
Type Item no. Description Weight
CVVA-IP 2GF1185-8AG IP-Module for 12 V DC / 24
V DC vandal-proof fix dome
camera
0.62 kg
Extra accessories, not included in the standard
supply!
PSU230-12 2GF1800-8BE 12 V DC camera power
supply
0.12 kg
CAPA2410-P230 2GF1800-8BJ 24 V AC camera power
supply
0.30 kg
7
Siemens Building Technologies
Fire Safety & Security Products
Norms and Directives
4 Norms and Directives
EU Directive
The following applies for the device described in this manual:
The product satisfies the requirements of the EU Electromagnetic Compatibility
Directive 89/336/EEC. The EU declarations of conformity can be made available to
the relevant authorities by:
Siemens Building Technologies
Fire & Security Products GmbH & Co. oHG
Siemensallee 84
D-76187 Karlsruhe
Application in accordance with the Electromagnetic Compatibility Directive
The device has been designed for industrial use and satisfies the following
requirements:
Electromagnetic
emissions:
EN 61000-6-3
Electromagnetic
immunity:
EN 50130-4 +A2
8
Siemens Building Technologies
Fire Safety & Security Products
Technical data
5 Technical data
5.1 Technical data for IP-Module CFVA-IP
Electrical supply 12 V DC/24 V AC
Power requirement max. 6.0 W
Operating temperature range -10 – +45 °C, max. relative humidity 90%
Storage temperature range -20 – +60 °C
Dimensions (H x Ø) 35.5 x 140 mm
Weight 400 g
Material Aluminum
System requirements All systems, which feature TCP/IP network functions and
provide an http browser (Microsoft Internet Explorer from
version 5.5 with Java plug-in or Mozilla or Netscape from
version 7.0).
Protocols ARP, BOOTP/DHCP, TCP/IP, HTTP, ICMP, SNMP, FTP
and DNS
Installation IP address configurable via ARP, BOOTP/DHCP,
connection to twisted-pair RJ45 Ethernet.
Network connection 10BaseT Ethernet or 100BaseTX Fast Ethernet, auto-
sensing, full/half duplex
Image formats QCIF (176x144),
CIF (352x288),
4CIF (704x576) (interlaced).
Image transmission Motion JPEG (multipart/x-mixed-replace content type),
user configurable JPEG single image frame quality,
streaming up to 25 images per second with QCIF and
CIF or up to 10 images per second with 4CIF.
Security Separate passwords for image access and system
configuration.
Hardware 8 MB RAM, 16 MB flash ROM
9
Siemens Building Technologies
Fire Safety & Security Products
Technical data
5.2 Technical data for IP-Module CVVA-IP
Electrical supply 12 V DC/24 V AC
Power requirement max. 6.0 W
Operating temperature range -10 – +50 °C, max. relative humidity 90%
Storage temperature range -20 – +60 °C, max. relative humidity 70%
Dimensions (H x Ø) 48 x 135 mm
Weight 620 g
Material Aluminum
IP rating IP66
System requirements All systems, which feature TCP/IP network functions and provide an
http browser (Microsoft Internet Explorer from version 5.5 with Java
plug-in or Mozilla or Netscape from version 7.0).
Protocols ARP, BOOTP/DHCP, TCP/IP, HTTP, ICMP, SNMP, FTP and DNS
Installation IP address configurable via ARP, BOOTP/DHCP, connection to twisted-
pair RJ45 Ethernet.
Network connection 10BaseT Ethernet or 100BaseTX Fast Ethernet, auto-sensing, full/half
duplex
Image formats QCIF (176x144),
CIF (352x288),
4CIF (704x576) (interlaced).
Image transmission Motion JPEG (multipart/x-mixed-replace content type), user
configurable JPEG single image frame quality, streaming up to 25
images per second with QCIF and CIF or up to 10 images per second
with 4CIF.
Security Separate passwords for image access and system configuration.
Hardware 8 MB RAM, 16 MB flash ROM
10
Siemens Building Technologies
Fire Safety & Security Products
Installing the IP-Module
6 Installing the IP-Module
6.1 Installing IP-Module type CFVA-IP
Fig. 1 Exploded view of IP-Module CFVA-IP
IP-Module fixing
1. Use the drilling template to drill two holes in the ceiling/wall and insert the wall
plugs.
2. Mount the IP-Module to the ceiling/wall.
3. Connect the BNC cable (12) to the connector socket (4) in the IP-Module.
Installation and connection of the dome camera
4. Connect the video output from the dome camera to the BNC cable video input
(11).
5. Connect the electrical supply for the dome camera to connector socket (5).
6. Remove the dome from the camera body (illustration D).
11
Siemens Building Technologies
Fire Safety & Security Products
Installing the IP-Module
7. Place the camera body on the IP-Module and screw both units together using
the two screws supplied.
8. Connect the LAN cable to the RJ45 socket (7).
9. Connect the (12 V DC / 24 V AC) electrical supply (8).
WARNING
Ensure correct polarity if using a 12 V DC supply, as incorrect connection may
damage the dome camera or cause the unit to operate abnormally.
10. Establish communication with the device for the first time. See section 7:
Establishing initial communication with the device.
11. A test monitor can be connected to the BNC socket (6) when configuring the
camera.
12. Configure the dome camera as required. Refer to the dome camera manual for
set-up instructions.
13. Place the dome back on the camera and screw it in position.
Clean the dome after installation using a soft, lint-free cloth to remove dust and greasy finger marks.
6.2 Installing IP-Module type CVVA-IP
Fig. 2 Exploded view of IP-Module CVVA-IP
12
Siemens Building Technologies
Fire Safety & Security Products
Loading...