SIEMENS ER926SB90 User Manual

Assembly instructions

please keep

Einbauanleitung

bitte aufbewahren

Notice de montage

veuillez conserver

Instruçoes de montagem

por favor, guardar

Installatievoorschrift

s.v.p. bewaren

Montaj talimatlarý

lütfen saklayýnýz

Istruzioni di Montaggio

si prega di conservarle

Instrucciones de montaje

por favor, guardar

Руководство по монтажу

пожалуйста, сохраните данное руководство

~60

~31

10 a

Read the appliance's instructions before installing and using. The graphics in these Assembly instructions are given as a guide only.

The manufacturer is exempt from all liability if this manual's requirements are not complied with.

Safety instructions

All operations relating to installation, regulation and conversion to other types of gas must be carried out by an authorised installation engineer, respecting applicable regulations, standards and the specifications of the gas and electricity providers. Before you begin, turn off the appliance's electricity and gas supply. You are recommended to contact the Technical Assistance Service to convert to another type of gas.

This appliance has been designed for home use only, not for commercial or professional use. This appliance cannot be installed on yachts or in caravans. The warranty will only be valid if the appliance is used for the purpose for which it was designed. Before installing, you need to check that local distribution conditions (gas type and pressure) and the appliance's adjustment are compatible (see table I). The appliance's adjustment conditions are written on the label or the specifications plate. This appliance can only be installed in a well-ventilated place in accordance with existing regulations and ventilation specifications. The appliance must not be connected to a combustion product evacuation device. The supply cable must be attached to the unit to prevent it from touching hot parts of the oven or hob. Appliances with electrical supply must be earthed. Do not tamper with the appliance's interior. If necessary, call our Technical Assistance Service.

Before installing

This appliance is class 3 type, according to the EN 30-1-1 regulation for gas appliances: built-in appliance. The units next to the appliance must be made of non-flammable materials. The laminated covering and glue for adhering it must be heat resistant. This appliance cannot be installed above fridges, washing machines, dishwashers or similar. An oven must have a power cooling fan to install a hob above it. Check the oven's dimensions in its installation manual. If an extractor fan is installed, you must follow the installation manual's instructions, always keeping a minimum distance of 650 mm to the hob.

Preparation of kitchen unit (fig. 1-2)

Make an appropriate size cut in the work surface. If the hob is electric or mixed (gas and electricity) and there is no oven below, place a non-flammable separator (e.g. metal or plywood) 10 mm from the bottom of the hob. This will prevent access to the base of the hob. If the hob is gas, it is recommendable to place the separator at the same distance. On wood work surfaces, varnish the cutting surfaces with a special glue. This protects them from moisture which could collect under the work surface.

Installation of appliance

Note: Wear protective gloves to fit the hob. The clips and the adhesive seal (underside of the hob) are factory-fitted: do not under any circumstances remove them. The seal ensures that the entire work surface will be watertight, and prevents water seepage. In order to fit the appliance into the kitchen unit, first place the hob in the correct position then loosen each of the clips so that they all turn freely (it is not necessary to completely undo them). Insert and centre the hob. Press the sides of the hob until it is supported around its entire perimeter. Turn the clips and tighten them fully. Fig. 3

Removal of hob

Turn off the appliance's electricity and gas supply. Unscrew the clips and proceed in the reverse order to installation.

Gas connection (fig. 4)

The end of the inlet connection point of the gas hob has a 1/2” (20.955 mm) thread that allows for:

- fixed connection.

- connection using a flexible metal pipe (L min. 1 m - max. 3 m) create a conical connection, insert the accessory with number 427950 and the seal with number 034308 (if required, included in the scope of delivery or available from the after-sales service) between the gas hob inlet pipe and the gas supply. Fig. 4a. In this case, you must prevent the pipe from coming into contact with moving parts of the kitchen unit being inserted (for example, a drawer) and prevent access to any spaces which might become obstructed. If you need to connect the gas supply horizontally, our Technical Assistance Service can supply you with an L-tube (code 173018) and a seal (code

034308). Fig. 4b. Warning! If any connection is handled, check the seal. Danger of leaks. The manufacturer is not liable for any connection leaking, after being handled.

. If you want to

Electric connection (fig. 5)

Check that the voltage and power of the appliance are compatible with the electrical installation. The hobs are supplied with a power cable with or without a wall socket plug. Provide an omnipolar cut-off switch with a minimum contact separation of 3 mm (except for plug connections, if the user has access to it). Appliances with plugs must only be connected to sockets that have earth wires correctly installed. This appliance is type “Y”: the supply cable can only be changed by the Technical Assistance Service and not the user. The cable type and minimum cross-section must be respected.

Changing the gas type

If the country's regulations allow, this appliance can be adapted to other types of gas (see specifications plate). The components required for this are in the transformation kit supplied (depending on the model) available from our Technical Assistance Service. The following steps should be taken:

A) Changing the nozzles of the rapid, semi-rapid and auxiliary burners on the hob (fig. 6):

- Remove the pan supports, burner covers and diffusers.

- Change the nozzles using the spanner provided by our Technical Assistance Service (code 424699), taking special care to ensure that the nozzle does not fall when it is removed from the burner or when fitted. Ensure that it is completely tightened in order to guarantee the seal. Primary air adjustment is not necessary with these burners.

B) Changing the nozzles for doubleflame burners (fig. 7):

The glass panel and frame are fixed to the rest of the hob using a clip mounting system. The following steps must be taken to remove the glass panel and frame:

- Remove all the burner covers and pan supports. Fig. 7a.

- Release the front clip fixing the appliance to the kitchen unit by removing the screw. Fig. 7b.

- Loosen the screws on the burners, fig. 7c-7d, and remove the control knobs from their respective housings. Use the disassembly lever 483196 available from our Technical Assistance Service. To release the front clips, apply the lever in the area shown in figures 8 according to the hob model.

Never use the lever on glass edges which have no trim or frame!

- To release the rear clips, carefully raise the entire glass panel and frame, as in fig. 8a.

Changing the outer flame nozzle (fig. 9a):

- Loosen the clamp screw to release the bushing by moving it backwards to access the main nozzle easily. Fig. a1.

+ 14 hidden pages