Page 1
DO NOT RETURN
THIS PRODUCT TO THE STORE!
Please read the following important information.
For Siemens Customer Care, product operation
information, or for problem resolution, call toll-free
1-888-777-0211
7 a.m. to 10 p.m. Central Standard Time EVERY DAY
www.icm.siemens.com
Visite nuestro sitio Web para obtener instrucciones en español.
Page 2
Gigaset 4210
Quick Start Guide
Basic Steps for Getting Started
For optimal performance of your system, please follow all of these steps.
For full details, see the User Manual.
Customer Care: 1-888-777-0211
Or visit our Website: www.icm.siemens.com
Visite nuestro sitio Web para obtener instrucciones en español.
PB4210QSG
Page 3
STEP 1
At the Base Station:
Base Station Setup
1 Insert small plug on cord into phone
jack. Place cord in base cable
channel. Insert power supply unit
into wall outlet.
2 Insert plug on telephone cord into
telephone jack on base unit (clicks
into place). Place cord in cable
channel on bottom of base. Insert
other end of plug into telephone
jack on wall.
IMPORTANT: For best reception, place the base in a high central
location, away from other electrical devices. The installation of
the base unit should allow at least 8-inches between the base and
persons to be in compliance with FCC RF exposure guidelines.
STEP 2
Handset Setup / Registration
At the Handset:
1 Remove protective plastic film from display.
2 Insert batteries as shown.
Power
supply unit
and cord
Bottom view of base
110 VAC
60 Hz
Telephone
jack and
cord
Page/
Registration
button
3 Place battery cover on back of handset
+
–
–
+
IMPORTANT: Charge batteries 12 to 14 hours before using the
handset for the first time.
Customer Care: 1-888-777-0211 or visit our Website: www.icm.siemens.com
Visite nuestro sitio Web para obtener instrucciones en español.
and push gently upward until it clicks into
place.
4 Be sure power
supply is
plugged into
wall outlet.
5 For auto registration
to base, press and
hold the END key to
turn handset off and
place in base station
with display facing
out for 1 minute.
Page 4
STEP 3
If you subscribe to Caller ID from your local telphone company, complete
the steps below. If you do not subscribe to Caller ID, skip this section.
To call back from the Call Log, you must enter and store the Local Area
Code for the area where your phone is installed. If your phone is
installed in an area with multiple area codes, you will also have to enter
and store the Extra Codes for that area.
STORING LOCAL AREA CODE
Area Codes
1 Open the Menu.
2 Scroll to Base Settings and press OK.
3 Scroll to Area Codes and press OK.
4 Scroll to Local Area Code and press OK.
5 Enter your area code and press OK.
STORING EXTRA AREA CODES
1 Open the Menu.
2 Scroll to Base Sett and press OK.
3 Scroll to Area Codes and press OK.
4 Scroll to Extra Codes and press OK.
5 To enter an extra area code, press Menu.
6 Enter an extra area code and press OK.
Repeat steps 5 and 6 above to enter additional area codes.
Customer Care: 1-888-777-0211 or visit our Website: www.icm.siemens.com
Visite nuestro sitio Web para obtener instrucciones en español.
Page 5
BASIC PHONE OPERATION
Making a Call 1 Dial desired number.
2 Press c or u speakerphone key.
3 Press a or place handset in base (or charger) to
hang up.
See Gigaset 4210 or 4215 User Manual for voice dialing instructions.
Answering Call Press c or u speakerphone key.
Intercom Call 1 Lift handset and select the handsets intercom number
F and press c.
2 Or, press the handset number, such as F,
3 Or, select Intercom Call and press c.
4 Or, select F,
Setting Volume 1 Open the Menu G.
« to call all handsets.
2 Scroll to Sound Settings D and
press OK.
3 Select Handset Volume and press OK.
You will hear the current volume of the speakerphone
and its level is displayed. Scroll to the desired volume
and press Save. You will hear and see in the display
the confirmation of the change.
4 To set earpiece volume, scroll down D, select
desired earpiece volume G, and press Save.
.
Language Setting 1 Open the Menu G .
2 Scroll to
H/Set Settings D and press
OK.
3 Scroll to Language and press OK.
4 Select the desired language and press OK.
A check mark appears next to the selected language.
Paging Handset Press the page button on the base bottom.
Customer Care: 1-888-777-0211 or visit our Website: www.icm.siemens.com
Visite nuestro sitio Web para obtener instrucciones en español.
Page 6
HANDSET NAVIGATIONAL OPERATION
Press the navigational (Navi) key H
to navigate through the handset options.
Navi Control Telephone Idle Action Lists and Menus Entry Field
E Hold down for Voice Dialing Upward Cursor up
D Open Directory Downward Cursor down
G Open Menu Select entry (OK) Cursor right
F List of internal/intercom users One menu level back (cancel) Cursor left
Display and Soft Keys
Signal strength:
Ðstrong
Ñmedium
Òweak
Date
Navigational (Navi) key
Ta lk ke y
In the Display:
Current functions
Ñ
05.20.01 10:30
Û
Int 2
MENURDL
××
Charging status:
Ý
battery empty
battery low when flashing
Ú
battery fully charged
Time
Soft keys:
Press the corresponding side
of the left or right soft key to
activate the function shown
in the display.
End call and On/Off key
Navigation Display Symbols
<>
Scroll to the left and right
when entering numbers or
messages.
Delete key (backspace):
Delete input from right to left.
X
Customer Care: 1-888-777-0211 or visit our Website: www.icm.siemens.com
Visite nuestro sitio Web para obtener instrucciones en español.
Page 7
DIRECTORY AND MEMORY DIALING
The handset Directory will store up to 200 telephone numbers.
STORING DIRECTORY ENTRIES
1 Open the Directory by pressing the Navi key on bottom D.
2 Scroll to New Entry and press OK.
3 Enter the telephone number and press OK.
4 Scroll and enter the name and press OK.
5 Press Menu G.
6 Save entry by pressing OK.
DIALING FROM DIRECTORY
1 Open the Directory by pressing the Navi key on bottom D.
2 Enter the first letter of the name as entered
(for example, press ^ 2 x for E, Eric).
3 Press the Talk cor Speakerphoneu key and the number is dialed.
The Memory dial list will store up to 9 telephone numbers. It is recommended that the 1
key be used for the answering machine or telephone company voice mail access.
STORING MEMORY ENTRIES
1 Press the Memory
C
key.
2 Scroll to New Entry and press OK.
3 Enter the telephone number and press OK.
Memory key
4 Using handset keypad, select a quick access key. Press the desired key
(2-9) and then enter the name (for example, to use quick access key 3
for Eric press ^ 4 x for 3, press ^ 2 x for E, press ¤ 3 x for
R, press ¡ 3 x for I, press 3 x for C).
5 Press OK.
6 Press Menu G.
7 Save entry by pressing OK.
DIALING FROM MEMORY
1 Press and hold the quick access key.
2 Press the Talk cor Speakerphoneu key and the number is dialed.
Customer Care: 1-888-777-0211 or visit our Website: www.icm.siemens.com
Visite nuestro sitio Web para obtener instrucciones en español.
Page 8
VOICE-OPERATED CONTROLS
Siemens GigaVoice voice-operated controls for the 4200 series allow users to place calls
or hear whos calling. The system recognizes up to 20 names and numbers from the
directory and up to four users may record the same name or number. Subscription to Caller
ID from your local telephone company is required.
RECORDING A VOICE-DIAL ENTRY
1 Open the Directory by pressing the Navi key on bottom.
2 Press Speech.
3 Select user 1-4 and press OK.
D
4 Scroll to New Entry and press OK.
5 Enter the telephone number.
6 Scroll to the name field and enter the name.
7 Press Record.
8 Press Begin to start recording and speak the name of the desired
entry (for example Anne) to record a voice pattern.
9 Repeat the name (for example Anne).
10 Press Save.
DIALING WITH YOUR VOICE
E
1 Press the Navi key on top.
2 At the prompt, speak the recorded voice pattern (for example Anne).
3 When the voice pattern is recognized, the name is played back from
the handset and the number is dialed.
VOICE-ANNOUNCED CALLER ID
If the Caller ID telephone number transmitted for an incoming call corresponds to a
voice-dial entry, the voice pattern is played back on the loudspeakers of the handset
or base station.
1 To turn on the Voice-Announced Caller ID feature, press Menu.
2 Scroll to Base Settings and press OK.
3 Scroll to Spec. Functions and press OK.
4 Scroll to Caller ID and press OK (checkmark indicates feature is on).
Customer Care: 1-888-777-0211 or visit our Website: www.icm.siemens.com
Visite nuestro sitio Web para obtener instrucciones en español.
Loading...