Operating instructions
Automated latch release
Window hardware
Door hardware
Sliding door hardware
Ventilation and building technology
Automatic door lock
Operating instructions
Contents
Intended use................................................................................................. 2
Automated latch release
ENGLISH
Improper use................................................................................................ 2
Safety notes.................................................................................................. 2
Switching the acoustic signal on and off........................................................ 3
Locking and unlocking the door..................................................................... 4
Operating the system with optional external devices.................................... 4
Programming............................................................................................... 5
Infra-red access keys.................................................................................... 6
Programming in the infra-red master key...................................................... 7
Programming in infra-red access keys.......................................................... 7
Deleting infra-red access keys....................................................................... 7
Replacing the batteries.................................................................................. 8
Disposing of batteries.................................................................................... 9
Malfunctions................................................................................................. 9
Technical specifications.................................................................................. 9
Liabilty............................................................................................10
1Last update: 01.08.2013
Automated latch release
Operating instructions
Intended use
UÊ The automated latch release is used in conjunction with automatic locking systems for unlocking doors by motor.
UÊ It is suitable for installation in timber, aluminium, steel and PVC front doors for residential and public buildings.
UÊ All assembly and electrical installation work must be carried out according to our assembly and installation instruc-
tions. Wiring the unit incorrectly can irreparably damage its electronic components.
UÊ The automated latch release can be connected to an external access control system (e.g. wireless, transponder or
fingerprint scanner system) via a voltage-free contact (switching time: min. 1 second).
UÊ Use the automated latch release only when it is in a technically sound condition. Do not modify the unit's components
in any way.
UÊ Use the automated latch release only with genuine KFV accessories.
Improper use
UÊ The automated latch release must not be installed in moisture-prone areas or areas with a corrosive atmosphere (e.g.
electroplating shops).
UÊ The length of the cable between the power supply and the automated latch release must not exceed 13 m.
Safety notes
UÊ Work on an 230 V AC mains power supply may only be performed by a qualified electrician.
UÊ All work on the 230 V AC mains power supply must be carried out in compliance with the current German VDE regu-
lations (e.g. VDE 0100) and any relevant country-specific requirements.
UÊ All-pole safety isolation should be used when fitting the power lead on-site.
UÊ Some external access control systems available on the market transmit a brief "open" signal when the operating
voltage is switched on. This can mean that the automated latch release will open the door following a power cut.
If in doubt, please contact the system manufacturer.
Warning
Where power supply cables are routed parallel to data cables (IDSN, DSL etc), interference can occur, eg: with
the data transfer speed.
2 Last update: 01.08.2013
Operating instructions
Automated latch release
Switching the acoustic signal on and off
In its "supplied" state, the automated latch release beeps as it draws the latch electrically into the changeover function.
It emits a constant beep for as long as terminal 4 receives an "open" signal. In some cases this constant beeping is undesirable, e.g. if the door needs to be kept unlocked to provide permanent access at certain times.
In this instance, the automated latch release can be prevented from beeping by programming it as described below.
1.) Retract all locking elements
2.) Open the door and hold it open
3.) Switch off the operating voltage
4.) Press and hold down the "open" button (terminal 2 (+) with terminal 4 ("open"))
5.) Switch on the operating voltage
6.) The automated latch release now switches to programming mode (a sequence of beeps is heard)
7.) Release the "open" button for about 1 s and press and hold it down once again
ENGLISH
8.) An sequence of beeps is generated to indicate that programming was successful
These programming steps can be followed any number of times in order to switch between the following two modes.
- Automated latch release beeps as the latch is drawn into the changeover function
- Automated latch release does not beep as the latch is drawn into the changeover function
Whichever mode is currently selected will remain active even if the power supply is interrupted.
3Last update: 01.08.2013
Automated latch release
Operating instructions
Locking and unlocking the door
Night mode
Locking the door: When the door clicks shut, the hookbolts in the additional lock cases automatically engage.
Unlocking the door: The door can be unlocked by turning the profile cylinder or the indoor lever handle, and
can be opened by the automated latch release.
Day mode
Locking the door: Using an optional device – the daytime unlocking mechanism – the hookbolts in the additi onal lock cases can be prevented from automatically engaging. In this case the door is
held shut by the latch only.
Unlocking the door: The door can be unlocked by turning the profile cylinder or the indoor lever handle, and
can be opened by the automated latch release.
Child safety lock
Locking the door: If the door is currently in night mode and was locked automatically, the deadbolt in the
main lock can be retracted by turning the profile cylinder. This places the lock in child
safety mode.
Unlocking the door: If the child safety lock is active, the door cannot be opened using the internal handle or
the automated latch release. To enable these actions, the child safety lock must first be
deactivated by turning the profile cylinder.
Operation with optional external devices
Handheld wireless transmitter Infra-red access key Transponder
Fingerprint scanner
- unlocking/opening - unlocking/opening- unlocking/opening- unlocking/opening
4 Last update: 01.08.2013
Operating instructions
Programming
Programming the handheld wireless transmitter
› Unscrew the cover on the receiver to access the programming button.
Automated latch release
L2
L3
12
345678910111213
ch1 ch2 ch3 ch4 ac / dc
01224
-++
14P115
P1
L1
› The green LED L1 lights up.
› Press down button P1 until the green LED L2 lights up.
› Press the required button on the handheld wireless transmitter.
› LED L2 flashes once and the relay is audibly activated.
› You have now programmed the button on the handheld wireless transmitter.
Note: If the red LED L3 lights up at the same time as the green LED L2, this indicates that the button on the handheld
wireless transmitter was already programmed, but has now been deleted.
ENGLISH
The other button on the handheld wireless transmitter can be assigned to the same wireless receiver or to a different
one, as required.
Deleting handheld wireless transmitters
If a handheld wireless transmitter has been lost or stolen, it cannot be deleted individually; all handheld wireless transmitters must be deleted at once.
› Press down button P1 until the green LED L2 lights up.
› Briefly release button P1, then press it down again until the red LED L3 and the green LED L2 light up three times.
› You have now deleted all handheld wireless transmitters. The remaining handheld wireless transmitters must be pro grammed in again.
Range between handheld wireless transmitter and receiver
Medium Range without aerial Range with aerial
Steel approx. 2 m approx. 5 m
Concrete approx. 10 m approx. 20 m
Timber, aluminium, PVC approx. 20 m approx. 30 m
Air approx. 30 m approx. 50 m
5Last update: 01.08.2013
Automated latch release
Infra-red access keys
Infra-red eye
In the infra-red eye there is a red LED which indicates whether the door is locked or open.
1 Solid light Door is open
2 Flashing Opening, or: fault (double speed)
3 Off Door is locked
123
Fig. 2 Determining whether the door is locked or unlocked
Operating instructions
Infra-red master key
The infra-red master key is needed for programming in
and deleting infra-red access keys. Before it can be
used for programming in infra-red access keys, it must
firstly be programmed in itself
UÊ Only one infra-red master key is permissible per F-
type automated latch release. However, any number
of F-type automated latch releases can be assigned to
a single infra-red master key.
UÊ The infra-red master key cannot be used to open the
door; it is for programming only.
Using infra-red access keys
For correct signal transmission, the infra-red access key
should be positioned between approx. 2 and 7 m from the
infra-red eye. The quality of the signal depends on the charge level of the batteries and the amount of sunlight. If the
infra-red eye is exposed to strong sunlight, the key should be
operated closer to the eye.
Unlocking/opening the door
› Press the "open" button. This will unlock the door. The
LED on the infra-red eye will light up.
Fig. 3: Infra-red master key
Important
UÊ For security reasons, if you lose the infra-red master key you should switch off the operating voltage on the automated
latch release until you have obtained a new infra-red master key from a specialist dealer and programmed it into the
system.
UÊ It is not possible to obtain information about opening sequences triggered by the integrated infra-red access control
system, as the automated latch release does not store this information.
UÊ For security reasons, all infra-red access keys must be programmed in individually.
UÊ The infra-red master key should always be kept under lock and key in order to prevent misuse.
6 Last update: 01.08.2013
Fig. 4 Infra-red access key
Operating instructions
Automated latch release
Programming in the infra-red master key
› Retract all locking elements.
› Open the door and hold it open.
› Switch off the operating voltage.
› Press and hold down the "open" button (terminal 2 (+24 V) with terminal 4 ("open"))
› Switch on the operating voltage.
› The red LED in the infra-red eye will flash.
› Hold the infra-red master key in front of the infra-red eye and press the button on it several times.
› The red LED in the infra-red eye will light up
› An acoustic signal is generated to indicate that programming was successful.
All infra-red access keys must now be activated once more.
Programming in infra-red access keys
ENGLISH
› Switch off the operating voltage. Wait for all LEDs to extinguish.
› Switch on the operating voltage.
› Hold the infra-red master key in front of the infra-red eye and press the button on it several times.
› The red LED will flash.
› Hold the access key in front of the infra-red eye and press any button on it.
› An affirmative sequence of beeps is generated to indicate that programming was successful.
› To check that programming was successful, press the "open" button on the infra-red access key once more.
› Switch on the operating voltage.
Deleting infra-red access keys
Important: The delete process always deletes all infra-red access keys.
› Retract all locking elements.
› Open the door and hold it open.
› Switch off the operating voltage.
› Press and hold down the "open" button (terminal 2 (+24 V) with terminal 4 ("open"))
› Switch on the operating voltage.
› The red LED in the infra-red eye will flash.
› Hold the infra-red master key in front of the infra-red eye and press the button on it several times.
› The red LED in the infra-red eye will light up.
› An acoustic signal is generated to indicate that programming was successful.
All infra-red access keys must now be programmed in again.
Setting up the fingerprint scanner
To set up the fingerprint scanner, please follow the instructions in the "Quick Reference" for the type F automated latch
release.
7Last update: 01.08.2013
Automated latch release
Replacing the batteries
Operating instructions
WARNING
- Batteries must be kept out of the reach of children due to a risk of swallowing. If they are swallowed, seek immediate
medical attention.
- Do not recharge, dismantle, heat up or burn batteries.
- Always wear protective gloves when handling spent or damaged batteries.
Risk of chemical burns from leaking battery acid
Handheld wireless transmitter
Note: Functions already programmed into the handheld wireless transmitter will remain unchanged following battery repla-
cement.
Fig. 4: Replacing the batteries in the handheld wireless transmitter
› Stack two CR 2016 batteries on top of one another with their positive terminals facing upwards, and place them in
the battery compartment.
Infra-red access keys
When the battery charge level has fallen to around 40%, the system will briefly beep three times at the end of the opening
sequence or the start of the programming sequence. These beeps serve as advance warning that the batteries need to be
replaced.
Note: Functions already programmed into the infra-red access key will remain unchanged following battery replacement.
Fig. 5: Replacing the batteries in infra-red access keys
› Stack two CR 2016 batteries on top of one another with their positive terminals facing upwards, and place them in
the battery compartment.
8 Last update: 01.08.2013
Operating instructions
Automated latch release
Disposing of batteries
The law requires that all spent standard and rechargeable batteries be returned to their manufacturer; they must not be
disposed of as household waste. Dispose of the batteries as required by the relevant authorities. Hand them in for recycling.
These batteries will be recycled as they may contain e.g. nickel oxide hydroxide and cadmium (Ni-Cd), lead (Pb), cadmium
(Cd) or mercury (Hg).
Malfunctions
Important: If the problem cannot be rectified as described below, do not open the automated latch release or attempt to
repair the system under any circumstances. Get the system repaired by a qualified specialist.
Malfunction Possible causes Action
The wireless receiver is not
receiving a signal
The door does not lock - Door is not fully closed
Door cannot be opened electrically
- Battery in handheld transmitter is too low
- Other systems (e.g. wireless headphones)
are transmitting signals of the same fre quency (433.92 MHz)
- Range too small
- Frame components are incorrectly positi oned
- Daytime unlocking mechanism is active
- Metal filings on release magnet
- Magnet is shielded by steel components
Circuit breaker in main fuse box has trip-
ped
Replace battery
Switch off other systems
(Fit wire aerial to wireless receiver)
Shut the door
Correct the Q adjustment
Deactivate daytime unlocking mechanism
Remove metal filings
Check recess for Q adjustment
Reset circuit breaker
ENGLISH
Technical specifications
Relative humidity
Ambient temperature in door
Dimensions Width 16 mm, length approx. 252 mm, depth 49 mm + width of face plate
Supply voltage
Cable types
Type LIYCY
Ambient temperature, non-fixed
Ambient temperature, fixed
20 % bis 80 %
-- 10 bis + 45 °C
24 V DC max. 500 mA
-- 5 bis + 50 °C
-- 20 bis + 70 °C
9Last update: 01.08.2013
Automated latch release
Operating instructions
Liability
Intended use
Any use of this product that is not in accordance with its intended use, or any adaptation of or modification to the product
and its associated components for which our express consent has not been obtained, is strictly prohibited. We accept no
liability whatsoever for any material losses or injury to people caused by failure to comply with this stipulation.
Product liability
Our products are guaranteed – subject to correct installation and proper use – for a period of one year from the date of receipt by a company (according to our general terms and conditions) or as otherwise agreed, and for a period of two years
for end consumers, in accordance with statutory provisions. As part of our ongoing improvements, we reserve the right to
replace individual components or entire products. Consequential losses resulting from defects are excluded from the warranty within the limits of the law. The warranty shall become void if modifications that are unauthorized by us or have not
been described in this documentation are performed on the product and/or individual components, or if the product and/or
individual components is/are dismantled or partly dismantled, and the defect is due to the changes made.
Exclusion of liability
The product and its components are subject to stringent quality controls. As a result, they function reliably and safely when
used correctly. Our liability for consequential losses and/or claims for damages is excluded, except in the case of wilful misconduct or gross negligence, or where we are responsible for injury to life, limb or health. Strict liability under the German
Product Liability Act (Produkthaftungsgesetz) remains unaffected. Liability for the culpable violation of significant contractual
obligations also remains unaffected; liability in this case is limited to losses that are specific to the contract and that could
have been foreseen. The above regulations do not imply a change in the burden of proof to the detriment of the consumer.
EU Declaration of Conformity
We, KFV KG, declare with full responsibility that this product complies with the provisions of Directives
2008/108/EC and 2006/95/EC of the Council of the European Union.
Environmental protection
Although our products do not fall within the scope of the German Electrical and Electronic Equipment Act (ElektroG), KFV
will continue to meet the requirements of this Act and will endeavour to completely eliminate the use of substances that are
hazardous to the environment as soon as this becomes technically feasible. Electrical products should not be disposed of as
household waste.
Feedback on documentation
We welcome your comments and suggestions on how to improve our documentation. Please send us your feedback by email to dokumentation@kfv.de.
10 Last update: 01.08.2013
Operating instructions
Automated latch release
ENGLISH
11Last update: 01.08.2013
KFV Karl Fliether GmbH & Co. KG
Siemensstraße 10
42551 Velbert
GERMANY
Telefon: +49 2051 278-0
Telefax: +49 2051 278-167
post@siegenia-aubi.com
www.siegenia-aubi.com
SIEGENIA-AUBI worldwide:
Austria Phone: +43 6225 8301
Belarus Phone: +375 17 312 1168
Benelux Phone: +32 9281 1312
China Phone: +86 316 5998198
France Phone: +33 38961 8131
Germany Phone: +49 271 3931-0
Great Britain Phone: +44 2476 622000
Contact your dealer:
Hungary Phone: +36 76 500810
Italy Phone: +39 02 935 3601
Poland Phone: +48 7744 77700
Russia Phone: +7 495 7211762
South Korea Phone: +82 31 7985590
Switzerland Phone: +41 33 346 10 10
Turkey Phone: +90 216 593 4151
Ukraine Phone: +380 44 4637979
H47.ELEKKFV0003EN/2013-08/0
Loading...