Sidchrome SCMTSA-1SHD Operation And Maintenance Manual

SCMTSA-1SHD
TABLE OF CONTENTS
Introduction 3 Speci cations 3 Safety Instructions 4
Getting Started 5 Tool Components 6 Contact Information 8
WARRANTY
Sidchrome air tools are warranted for TWO (2) years from the date of purchase, excluding normally wearing parts such as vanes, gaskets and o-rings;
1. Unless otherwise speci ed, this warranty does not cover: (a) modi ed, abused, neglected, accidentally damaged or excessively worn products, or products that have become
damaged or defective as a result of improper use; (b) repairs attempted or made by other than our regional repair centre or authorised warranty service centre; (c) conditions or malfunctions caused by the reasonable e ects of fair wear and tear or the malfunction of normally
wearing parts, which include but are not limited to: vanes, gaskets, o-rings, driver blades, bumpers, pistons and
piston rings; (Warranty non-transferrable)  is warranty is not transferrable beyond the original purchaser.
2. How to make a warranty claim Unless otherwise speci ed, the process for making a warranty claim is as follows:
(a) Any product subject to a warranty claim should be returned to the place of purchase for assessment by a
Sidchrome Australia distributor or representative. You are responsible for returning the product to the place of
purchase unless the cost of returning, removing or transporting the product is signi cant, in which case you
should contact Sidchrome Australia to make alternative arrangements. (b) You must present proof of purchase when making a warranty claim. (c)  e claim under this warranty (you may have additional rights under the Australian Consumer Law) will be
assessed by a Sidchrome Australia distributor or representative on the basis of their product knowledge and
reasonable judgment and will be accepted if: (i) a relevant defect is found; (ii) the warranty claim is made during the relevant warranty period (iii) none of the exclusions in cl 1. of this warranty apply. (d) Upon acceptance of a claim under this warranty, Sidchrome Australia will send you a replacement product or
arrange for your product to be repaired free of charge. (e) Any warranty related enquiries or claims may be directed to Sidchrome Australia at the address or contact details
listed below.
3. Repair notices Goods presented for repair may be replaced by refurbished goods of the same type rather than being repaired. Refurbished parts may be used to repair the goods.
 e repair of your goods may result in the loss of any user-generated data. Please ensure that you have made a copy of any data saved on your goods.
 e Consumer Guarantee Statement Our goods come with guarantees that cannot be excluded under Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Warranty related enquiries and claims may be directed to: Sidchrome Australia 82 Taryn Drive, Epping, Victoria 3076 http://www.sidchrome.com.au/contact
Australia Phone 1800 338 002
Fax 1800 080 898
New Zealand Phone 0800 4782 6539
Fax 0800 278 265
INTRODUCTION
 e
Sidchrome® SCMTSA-1SHD is a precision-built tool, designed for torque assembly and disassembly of threaded
fasteners.  is tool will deliver e cient, dependable service when used correctly and with care. As with any  ne power tool, for best performance the manufacturer’s instructions must be followed. Please study this manual before operating the tool and understand the safety warnings and cautions.  e instructions on installation, operation and maintenance should be read carefully, and the manuals kept for reference. NOTE: Additional safety measures may be required because of your particular application of the tool. Contact your
Sidchrome® representative or distributor with any questions
concerning the tool and its use.
Sidchrome®
82 Taryn Drive, Epping
Victoria, Australia 3076
1800 338 002
Sidchrome.com.au
SPECIFICATIONS
Twin-Hammer
Impact Mechanism
Multiple Position Power Regulator
3
Aluminum 2-pc Construction
Variable Speed
Trigger
Model #
Square
Drive
Blow
Rate
Breakaway
Torque
in bpm ft-lbs / Nm
SCMTSA-ϭSHD 1 720 3000 / 4068 103.4 3* 114.4 3* 103.0 3* 16.7 2.15**
Model #
Free
Speed
Average Air
Consumption
Working Pressure
Weight
rpm cfm / l/min psi / bar lbs / kg
SCMTSA-ϭSHD 4400 8.6 / 243 90 / 6.2 22.7 / 10.3
* = measurement uncertainty in dB(A) ** = measurement uncertainty in m/s²
SPECIFICATIONS
Noise Level
Vibration
Level
Pressure dB(A) Power dB(A) Pressure dB(C)
11.9 x 8.1 x 11.4 / 301 x 205 x 290
m/s²
Dimensions
in / mm
Loading...
+ 5 hidden pages