WIFI-2-Q379UWP1
Model
Standard
Rate
Band
Antenna
Power
WIFI-2-Q379UWP1
IEEE 802.11a/b/g/n/ac
866.7Mbps
2.4G/5G
Internal
Antennas
Design
5V
BT2.1+EDR/3.0+HS/4.2
3Mbps
2.4G
WiFi Module
Integrated Bluetooth 2.1+EDR/3.0+HS/4.2
Features：
Reserving System
IEEE Std. 802.11a
IEEE Std. 802.11b
IEEE Std. 802.11g
IEEE Std. 802.11n
IEEE Std. 802.11ac
AI-Link
Bluetooth 2.1+EDR/3.0+HS/4.2
Chip Solution
Qualcomm9379-7
Size
33.0mm x70.0mm x 6.0mm
Model Overview：
Sichuan AI-Link Technology Co.,Ltd.
Add: Anzhou,Industrial park,Mianyang,Sichuan
Web: http://www.changhong.com
AI-Link WIFI-2-Q379UWP1
QCA9379-7
Dixplexer
Dixplexer
Antenna0
Antenna1
48MHz
Antenna2
RFIO
RFIO
BT_
RFIO
Filter
IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/3.0+HS/4.2
1. Introduction
WIFI-2-Q379UWP1 module design is based on Qualcomm9379-7 solution, The QCA9379-7 is a
highly integrated single chip which has built in a 2x2 dual-band wireless LAN radio and Bluetooth radio.
It includes Bluetooth EDR and LE radio which complies with Bluetooth v2.1+EDR, v3.0+HS, and v4.2.
The Module is a highly integrated MAC/BBP and 2.4/5GHz PA/LNA single chip which supports a
866.7Mbps PHY rate. The Module is designed to support standard-based features in the areas of
security, quality of service, and international regulations, giving end users the greatest performance
anytime and in any circumstance. This documentation describes the engineering requirements
specification.
1.1 RF module Overview
The general HW architecture for the module is shown in Figure 1. This WLAN Module design is based
on Qualcomm QCA9379-7. It is a highly integrated single-chip MIMO(Multiple In Multiple Out) Wireless
LAN (WLAN) network interface controller complying with the 802.11 specification and Bluetooth over
USB interface. It combines a MAC, a 2T2R capable baseband, and RF in a single chip. An intelligent
Wi-Fi/Bluetooth coexistence algorithm is implemented to provide the best harmonized Wi-Fi and
Bluetooth radio performance.
5V INPUT
GPIO
WLAN USB2.0 Interface
BT USB1.1 Interface
2.4G TX0/RX0
WF_
WF_
5G TX0/RX0
2.4G TX1/RX1
5G TX1/RX1
BT TX2/RX2
Figure 1 WIFI-2-Q379UWP1 Block Diagram
Sichuan AI-Link Technology Co.,Ltd. page 2 of 14
AI-Link WIFI-2-Q379UWP1
Main Chipset
Qualcomm QCA9379-7
Operating Frequency
2.4G/5G
WiFi Standard
802.11a/b/g/n/ac (2x2)
Bluetooth
2.1+EDR/3.0+HS/4.2
Modulation
WIFI:11b: DBPSK, DQPSK and CCK and DSSS
11a/g: BPSK, QPSK, 16QAM, 64QAM and OFDM
11n: BPSK, QPSK, 16QAM, 64QAM and OFDM
11ac: BPSK, QPSK, 16QAM, 64QAM,256QAM and OFDM
BT: FHSS,GFSK,DPSK,DQPSK
Data rates
11b: 1, 2, 5.5 and 11Mbps
11a/g: 6, 9, 12, 18, 24, 36, 48 and 54 Mbps
11n: MCS0~15, up to 300Mbps
11ac: MCS0~9, Nss=2, up to 866.7Mbps
Form factor
13pins ,
Host Interface
USB 2.0 for WLAN and USB 1.1 for BT
PCB Stack
6-layers design
Dimension
Typical，33mm x 70mm x 6mm
Antenna
Internal Antennas Design
Operation Temperature
0℃ to +70℃
Storage Temperature
-15℃ to +45℃
Operation Voltage
5V +/-10%
IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/3.0+HS/4.2
1.2 Specification reference
This specification is based on additional references listed below.
_ IEEE Std. 802.11a
_ IEEE Std. 802.11b
_ IEEE Std. 802.11g
_ IEEE Std. 802.11n
_ IEEE Std. 802.11ac
_ Bluetooth 2.1+EDR/3.0+HS/4.2
1.3 System Functions
Table1: General Specification as below:
Sichuan AI-Link Technology Co.,Ltd. page 3 of 14
AI-Link WIFI-2-Q379UWP1
IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/3.0+HS/4.2
2. Mechanical Specification
2.1 Mechanical Outline Drawing
Typical Dimension (W x L ): 33.0mmx 70.0mm x 6.0mm
General tolerance: ±0.15mm
TOP VIEW BOTTOM VIEW
2.2 Product Picture
TOP VIEW BOTTOM VIEW
Sichuan AI-Link Technology Co.,Ltd. page 4 of 14
AI-Link WIFI-2-Q379UWP1
No
Define
description
1
WIFI_REG_ON
WLAN enable，active high
2
BT_HOST_WAKE
Bluetooth wakeup the host，active high
3
WL_VCC
WLAN 5V input
4
WI-FI DN
WIFI USB D-/DN
5
WIFI DP
WIFI USB D+/DP
6
GND
Ground
7
3D_SYNC
Frame sync signals from TV to sync with 3D glass via
Bluetooth
8
Reset
Bluetooth enable，active high
9
WLAN_DEV_WAKE
WIFI wakeup the host, active high
10
BT_VCC
BT 5V input
11
BTDN
BT USB D-/DN
12
BTDP
BT USB D-/DP
13
GND
Ground
IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/3.0+HS/4.2
2.3 Pin definition
Sichuan AI-Link Technology Co.,Ltd. page 5 of 14
AI-Link WIFI-2-Q379UWP1
Items
Contents
Specification
IEEE802.11g & IEEE802.11a
Mode
BPSK, QPSK, 16QAM, 64QAM and OFDM
Channel
CH1 to CH13 @ 11g
CH36 to CH165 @ 11a
Data rate
6, 9, 12, 18, 24, 36, 48, 54Mbps
TX Characteristics
Min.
Typ.
Max.
Unit
Remark
1. Power Levels
1) 14.5dBm Target (For Each antenna port)
@ 11g 54Mbps
12
14.5
16
dBm
2) 13.5dBm Target (For Each antenna port)
@ 11a 54Mbps
12
13.5
15
dBm
2. Spectrum Mask @ Target Power
1) at fc +/-11MHz
- - -20
dBr
2) at fc +/-20MHz
- - -28
dBr
3) at fc > +/-30MHz
- - -40
dBr
3. Constellation Error(EVM) @ Target Power
1) 6Mbps
- - -5
dB
2) 9Mbps
- - -8
dB
3) 12Mbps
- - -10
dB
4) 18Mbps
- - -13
dB
5) 24Mbps
- - -16
dB
6) 36Mbps
- - -19
dB
7) 48Mbps
- - -22
dB
8) 54Mbps
- - -25
dB
4. Frequency Error
1) IEEE802.11g
-25- 25
ppm
2) IEEE802.11a
-30
30
ppm
RX Characteristics
Min.
Typ.
Max.
Unit
5. Minimum Input Level Sensitivity(each chain)
1) 6Mbps (PER ≦10%)
- - -82
dBm
2) 9Mbps (PER ≦10%)
- - -81
dBm
3) 12Mbps (PER ≦10%)
- - -79
dBm
4) 18Mbps (PER ≦10%)
- - -77
dBm
5) 24Mbps (PER ≦10%)
- - -74
dBm
6) 36Mbps (PER ≦10%)
- - -70
dBm
7) 48Mbps (PER ≦10%)
- - -66
dBm
8) 54Mbps (PER ≦10%)
- - -65
dBm
6. Maximum Input Level (PER ≦10%)
1) IEEE802.11g
-20- -
dBm
2) IEEE802.11a
-30
dBm
IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/3.0+HS/4.2
3. Electrical Specification
This Specification is based-on conductive DVT testing result. The extreme condition include overall
temperature (0℃,+25℃,+40℃) and overall voltage (4.5V,5.0V,5.5V).
3. 1 IEEE 802.11g/a Section:
Sichuan AI-Link Technology Co.,Ltd. page 6 of 14
AI-Link WIFI-2-Q379UWP1
Items
Contents
Specification
IEEE802.11b
Mode
DBPSK, DQPSK and CCK and DSSS
Channel
CH1 to CH13
Data rate
1, 2, 5.5, 11Mbps
TX Characteristics
Min.
Typ.
Max.
Unit
Remark
1. Power Levels(Calibrated)
1) 17dBm Target (For Each antenna port)
@1Mbps~11Mbps
16
17.5
19
dBm
2. Spectrum Mask @ Target Power
1) fc +/-11MHz to +/-22MHz
- - -30
dBr
2) fc > +/-22MHz
- - -50
dBr
3. Constellation Error(EVM) @ Target Power
1) 1Mbps
- - -10
dB
2) 2Mbps
- - -10
dB
3) 5.5Mbps
- - -10
dB
4) 11Mbps
-
-20
-10
dB
4. Frequency Error
-25- 25
ppm
RX Characteristics
Min.
Typ.
Max.
Unit
5. Minimum Input Level Sensitivity(each chain)
1) 1Mbps (FER ≦8%)
-
-83
-76
dBm
2) 2Mbps (FER ≦8%)
-
-80
-76
dBm
3) 5.5Mbps (FER ≦8%)
-
-79
-76
dBm
4) 11Mbps (FER ≦8%)
-
-76
-76
dBm
6. Maximum Input Level (FER ≦8%)
-10- -
dBm
IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/3.0+HS/4.2
3.2 IEEE 802.11b Section:
Sichuan AI-Link Technology Co.,Ltd. page 7 of 14
AI-Link WIFI-2-Q379UWP1
Items
Contents
Specification
IEEE802.11n HT20 @ 2.4G
IEEE802.11n HT20 @ 5G
Mode
BPSK, QPSK, 16QAM, 64QAM and OFDM
Channel
CH1 to CH13 @ 2.4G
CH36 to CH165 @ 5G
Data rate (MCS index)
MCS0/1/2/3/4/5/6/7/8/9/10/11/12/13/14/15
TX Characteristics
Min.
Typ.
Max.
Unit
Remark
1. Power Levels
1) 14.5dBm Target (For Each antenna port)
@ 2.4G/MCS7
13
14.5
16
dBm
2) 13.5dBm Target (For Each antenna port)
@ 5G/MCS7
12
13.5
15
dBm
2. Spectrum Mask @ Target Power
1) at fc +/-11MHz
- - -20
dBr
2) at fc +/-20MHz
- - -28
dBr
3) at fc > +/-30MHz
- - -45
dBr
3. Constellation Error(EVM) @ Target Power
1) MCS0
- - -5
dB
2) MCS1
- - -10
dB
3) MCS2
- - -13
dB
4) MCS3
- - -16
dB
5) MCS4
- - -19
dB
6) MCS5
- - -22
dB
7) MCS6
- - -25
dB
8) MCS7
- - -28
dB
4. Frequency Error
1) IEEE802.11n HT20 @ 2.4G
-25- 25
ppm
2) IEEE802.11n HT20 @ 5G
-20- 20
ppm
RX Characteristics
Min.
Typ.
Max.
Unit
5. Minimum Input Level Sensitivity(each chain)
1) MCS0 (PER ≦10%)
- - -82
dBm
2) MCS1 (PER ≦10%)
- - -79
dBm
3) MCS2 (PER ≦10%)
- - -77
dBm
4) MCS3 (PER ≦10%)
- - -74
dBm
5) MCS4 (PER ≦10%)
- - -70
dBm
6) MCS5 (PER ≦10%)
- - -66
dBm
7) MCS6 (PER ≦10%)
- - -65
dBm
8) MCS7 (PER ≦10%)
- - -64
dBm
6. Maximum Input Level (PER ≦10%)
1) IEEE802.11n HT20 @ 2.4G
-20- -
dBm
2) IEEE802.11n HT20 @ 5G
-30- -
dBm
IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/3.0+HS/4.2
3.3 IEEE 802.11n HT20 Section:
Sichuan AI-Link Technology Co.,Ltd. page 8 of 14
AI-Link WIFI-2-Q379UWP1
Items
Contents
Specification
IEEE802.11n HT20 @ 2.4G
IEEE802.11n HT20 @ 5G
Mode
BPSK, QPSK, 16QAM, 64QAM and OFDM
Channel
CH3 to CH11 @ 2.4G
CH38 to CH163 @ 5G
Data rate (MCS index)
MCS0/1/2/3/4/5/6/7/8/9/10/11/12/13/14/15
TX Characteristics
Min.
Typ.
Max.
Unit
Remark
1. Power Levels (Calibrated)
1) 13.5dBm Target (For Each antenna port)
@ 2.4G/MCS7
12
13.5
15
dBm
2) 12.5dBm Target (For Each antenna port)
@ 5G/MCS7
11
12.5
14
dBm
2. Spectrum Mask @ Target Power
1) at fc +/-21MHz
- - -20
dBr
2) at fc +/-40MHz
- - -28
dBr
3) at fc > +/-60MHz
- - -45
dBr
3. Constellation Error(EVM) @ Target Power
1) MCS0
- - -5
dB
2) MCS1
- - -10
dB
3) MCS2
- - -13
dB
4) MCS3
- - -16
dB
5) MCS4
- - -19
dB
6) MCS5
- - -22
dB
7) MCS6
- - -25
dB
8) MCS7
- - -28
dB
4. Frequency Error
1) IEEE802.11n HT20 @ 2.4G
-25- 25
ppm
2) IEEE802.11n HT20 @ 5G
-20- 20
ppm
RX Characteristics
Min.
Typ.
Max.
Unit
5. Minimum Input Level Sensitivity(each chain)
1) MCS0 (PER ≦10%)
- - -79
dBm
2) MCS1 (PER ≦10%)
- - -76
dBm
3) MCS2 (PER ≦10%)
- - -74
dBm
4) MCS3 (PER ≦10%)
- - -71
dBm
5) MCS4 (PER ≦10%)
- - -67
dBm
6) MCS5 (PER ≦10%)
- - -63
dBm
7) MCS6 (PER ≦10%)
- - -62
dBm
8) MCS7 (PER ≦10%)
- - -61
dBm
6. Maximum Input Level(PER ≦10%)
1) IEEE802.11n HT20 @ 2.4G
-20- -
dBm
2) IEEE802.11n HT20 @ 5G
-30- -
dBm
IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/3.0+HS/4.2
3.4 IEEE 802.11n HT40 Section:
Sichuan AI-Link Technology Co.,Ltd. page 9 of 14
AI-Link WIFI-2-Q379UWP1
Items
Contents
Specification
IEEE802.11ac
Mode
BPSK, QPSK, 16QAM, 64QAM ,256QAM and OFDM
Channel
CH36 to CH165 VHT20
CH38 to CH163 VHT40
CH42 to CH157 VHT80
Data rate (MCS index)
MCS0/1/2/3/4/5/6/7/8/9
TX Characteristics
Min.
Typ.
Max.
Unit
Remark
1. Power Levels (Calibrated)
1) 12.5dBm Target (For Each antenna port)
@VHT20 MCS8
11
12.5
14
dBm
2) 10.5dBm Target (For Each antenna port)
@VHT40 MCS9
9
10.5
12
dBm
3) 9.5dBm Target (For Each antenna port)
@VHT80 MCS9
8
9.5
11
dBm
2. Spectrum Mask @ Target Power
1) at fc +/-11MHz /20MHz/30MHz
-
-
-20
dBr
2) at fc +/-21MHz /40MHz/60MHz
-
-
-28
dBr
3) at fc +/-41MHz /80MHz/120MHz
-
-
-40
dBr
3. Constellation Error(EVM) @ Target Power
1) MCS0- - -5dB
2) MCS1- -
-10
dB
3) MCS2- -
-13
dB
4) MCS3- -
-16
dB
5) MCS4- -
-19
dB
6) MCS5- -
-22
dB
7) MCS6- -
-25
dB
8) MCS7- -
-27
dB
9) MCS8
-30
dB
10) MCS9
-32
dB
4. Frequency Error
-10
-
10
ppm
RX Characteristics
Min.
Typ.
Max.
Unit
5. Minimum Input Level Sensitivity(each chain)
VHT20
VHT40
VHT80
1) MCS0 (PER ≦10%)
- - -82
-79
-76
dBm
2) MCS1 (PER ≦10%)
- - -79
-76
-73
dBm
3) MCS2 (PER ≦10%)
- - -77
-74
-71
dBm
4) MCS3 (PER ≦10%)
- - -74
-71
-68
dBm
5) MCS4 (PER ≦10%)
- - -70
-67
-64
dBm
6) MCS5 (PER ≦10%)
- - -66
-63
-60
dBm
7) MCS6 (PER ≦10%)
- - -65
-62
-59
dBm
8) MCS7 (PER ≦10%)
- - -64
-61
-58
dBm
9) MCS8 (PER ≦10%)
- - -59
-56
-53
dBm
10) MCS9 (PER ≦10%)
- - -57
-54
-51
dBm
6. Maximum Input Level(PER ≦10%)
-30
-
-
dBm
IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/3.0+HS/4.2
3.5 IEEE 802.11ac Section:
Sichuan AI-Link Technology Co.,Ltd. page 10 of 14
AI-Link WIFI-2-Q379UWP1
Items
Contents
Specification
BT2.1+EDR/4.2/5.0
Mode
FHSS,GFSK,DPSK,DQPSK
Number of Channel
79 Channels
Frequency Band
2.402 GHz ~2.480GHz
Min.
Typ.
Max.
Unit
Remark
1. Output Power
7.5 9 -
dBm
2.Gain step
2 4 8
dB
3. Receiver sensitivity (BER ≦0.1%)
-
-93.5
-80
dBm
4. Maximum usable signal (BER ≦0.1%)
-
-5
-
5. C/I co-channel (BER<0.1%)
- 4 11
dB
6. C/I 1MHz (BER<0.1%)
-
-14 0 dB
7. C/I 2MHz (BER<0.1%)
-
-42
-30
dB
8. C/I≥3MHz (BER<0.1%)
-
-49
-40
dB
9. C/I Image channel (BER<0.1%)
-
-25 -9dB
10. C/I Image 1MHz (BER<0.1%)
-
-50
-20
dB
11. Inter-modulation
-
-13 - dB
12. Out-of-band blocking
1). 30MHz to 2000MHz
-10- -
dBm
2). 2000MHz to 2399MHz
-27- -
dBm
3). 2498MHz to 3000MHz
-27- -
dBm
4). 3000MHz to 12.75GHz
-10- -
dBm
13. Modulation characteristics
1). Δf1avg
140
157
175
KHz
2). Δf2max (For at least 99.9% of all Δf2max)
115
140 - KHz
3). Δf1avg /Δf2avg
0.8
0.98 - KHz
14. ICFT
-75
±20
+75
KHz
15. Carrier frequency drift
1). One slot packet (DH1)
-25
±15
+25
KHz
2). Two slot packet (DH3)
-40
±15
+40
KHz
3). Five slot packet (DH5)
-40
±15
+40
KHz
4). Max drift rate
- 6 20
KHz/50us
16. TX output spectrum(20dB bandwidth)
-
922
1000
KHz
17. In-Band spurious emission
1). ±2MHz offset
-
-45
-20
dBm
2). ±3MHz offset
-
-48
-40
dBm
3). >±3MHz offset
-
-48
-40
dBm
IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/3.0+HS/4.2
3.6 Bluetooth Section:
Sichuan AI-Link Technology Co.,Ltd. page 11 of 14
AI-Link WIFI-2-Q379UWP1
Description
Average current（mA）
Wi-Fi Standby mode current
30mA
BT Standby mode current:
15mA
Power Saving Mode
2.2mA
Wi-Fi cont. TX mode
610mA
Wi-Fi cont. Rx mode
260mA
BT cont. TX mode
50mA
BT cont. Rx mode
25mA
IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/3.0+HS/4.2
4. Current consumption
5. Software Requirements
The driver supports the following operating systems: Linux, Microsoft Windows XP, Vista and Win7.
Mfg. software tool is QDART
Sichuan AI-Link Technology Co.,Ltd. page 12 of 14
AI-Link WIFI-2-Q379UWP1
IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/3.0+HS/4.2
6. Package
Pallet size：
Line of production
Sichuan AI-Link Technology Co.,Ltd. page 13 of 14
AI-Link WIFI-2-Q379UWP1
空托盘
共 层托盘30
IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/3.0+HS/4.2
Packing desrciption:
Pallet
15 layers
Other requirements are subject to the standard of hisense.
Sichuan AI-Link Technology Co.,Ltd. page 14 of 14
AI-Link WIFI-2-Q379UWP1
IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/3.0+HS/4.2
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, usesand can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does causeharmful interference to radio
or television reception, which can be determined by turning theequipment off and on, the user is
encouraged to try to correct the interference by one or more ofthe following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
The modular can be installed or integrated in mobile or fix devices only. This modular cannot be
installed in any portable device .
FCC Radiation Exposure Statement
This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter. This modular must be installed and operated with a minimum distance of 20 cm between the
radiator and user body.
If the FCC identification number is not visible when the module is installed inside another device,
then the outside of the device into which the module is installed must also display a label
referring to the enclosed module. This exterior label can use wording such as the following: “Contains
Transmitter Module FCC ID:2AOKI-WIFI2Q379UWP1 Or Contains FCC ID:2AOKI-WIFI2Q379UWP1”
When the module is installed inside
another device, the user manual of the host must contain below warning statements;
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause
undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
The devices must be installed and used in strict accordance with the manufacturer's instructions as
described in the user documentation that comes with the product.
Sichuan AI-Link Technology Co.,Ltd.
AI-Link WIFI-2-Q379UWP1
IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/3.0+HS/4.2
IC STATEMENT
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science
and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following
two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired
operation of the device
Cet appareil contient des émetteurs / récepteurs exemptés de licence conformes aux RSS (RSS)
d'Innovation, Sciences et Développement économique Canada. Le fonctionnement est soumis
aux deux conditions suivantes :
(1) Cet appareil ne doit pas causer d'interférences.
(2) Cet appareil doit accepter toutes les interférences, y compris celles susceptibles de
provoquer un fonctionnement indésirable de l'appareil.
IC Radiation Exposure Statement
The modular can be installed or integrated in mobile or fix devices only. This modular cannot
be installed in any portable device.
This modular complies with IC RF radiation exposure limits set forth for an uncontrolled environment.
This transmitter must not be co-located or operating in conjunction with any other antenna or t
ransmitter. This modular must be installed and operated with a minimum distance of 20 cm between the
radiator and user body. Cette modulaire doit être installé et utilisé à une distance minimum de 20cm
entre le radiateur et le corps de l'utilisateur.
If the IC number is not visible when the module is installed inside another device, then the outside
of the device into which the module is installed must also display a label referring to the
enclosed module. This exterior label can use wording such as the following:
"Contains IC: "
when the module is installed inside another device, the user manual of this device must contain
below warning statements;
1. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the
following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
2. Cet appareil contient des émetteurs / récepteurs exemptés de licence conformes aux RSS (RSS)
d'Innovation, Sciences et Développement économique Canada. Le fonctionnement est soumis aux
deux conditions suivantes :
( 1 ) Ce dispositif ne peut causer d'interférences ; et
( 2 ) Ce dispositif doit accepter toute interférence , y compris les interférences qui peuvent causer
un mauvais fonctionnement de l'appareil.
23460-WFQ379UWP1
The devices must be installed and used in strict accordance with the manufacturer's instructions
as described in the user documentation that comes with the product
Sichuan AI-Link Technology Co.,Ltd.
AI-Link WIFI-2-Q379UWP1
IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module&BT2.1+EDR/3.0+HS/4.2
NB Statement
Herby,Sichuan AI-Link Technology Co., Ltd.declares that this WiFi Module, WIFI-2-Q379UWP1 is
in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.
In accordance with Article 10(2) and Article 10(10), this product allowed to be used in all
EU member states.
Use the WiFi Module in the environment with the temperature between 0 and 60
Operation Frequency:
For BT/BLE:
2402MHz~2480MHz
For 2.4G WIFI:
2412MHz~2472MHz (802.11b/802.11g/802.11n(HT20))
2422MHz~2462MHz (802.11n(HT40))
For 5G WIFI:
5150MHz-5350MHz, 5470MHz-5725MHz, 5745MHz-5825MHz
Max output power:
BT: 0.0048W
BLE: 0.0008W
Wifi(2.4G): 0.0637W
Wifi(5G): 0.0596W
Manufacturer: Sichuan AI-Link Technology Co., Ltd.
Address: Anzhou, Industrial park, Mianyang, Sichuan, China
Tel: +86-0816-2438701
Fax: +86-0816-2438701
E-mail: caixia.hu@changhong.com
Sichuan AI-Link Technology Co.,Ltd.
Loading...