Sibeam Snap MOD6212, Snap MOD6213 Installation Manual
SiBEAM Snap™
OEM Module Installation Guide for
MOD6212/13
Module Installation Guide
USB3.0/2.0
I2C Tunnel
System
Host
MOD6212
USB3.0/2.0
I/O RST
USB devices
I2C peripherals
System controller
3.3V 3.3V
MOD6213
I2C D ebug
I/O RST
I2C D ebug
I2C Tunnel
Introduction
The Lattice Semiconductor MOD6212/13 Wireless module provides a data interface
compatible with USB device, which allows reception/transmission of various data rate
from/to any USB compliant device. OEM can develop a system equipped with this module to
wirelessly connect their high data sources to the target device.
The MOD6212/13 modules fit into a variety of industrial designs. No software needs to
initialize and to control the module to achieve the wired connectivity offered. The
MOD6212/13 module is a completely self-contained autonomous wireless sub-system that
connects to a system board that provides the wired connectivity from a single port to a full
featured multiport, multi-standard system. The advantage of this design is that the
complexity of the wireless system, radio performance, regulatory requirements, and
compliance to standards are all eliminated. This system interface carries data, power, and
control signals. The module is pre-certified and is fully tested for fast time-to-market.
MOD6212/13 Diagram
Figure 1. MOD6212/13 Transceiver Module Wireless connector principle
MOD6212/13 transceiver Features
• USB 3.0 and 2.0 connections: SS, HS, FS, LS.
• Up to 6Gbps full duplex data-rate
• I
• Fully automatic device detection and connection
• Close proximity operation
• Single chip IC, direct connector replacement
• Integrated antenna
• No software driver required
2 ©2017 SiBEAM, Inc., a Lattice Semiconductor company.
2
C tunneling for remote I2C connections
All rights reserved. CONFIDENTIAL
Module Installation Guide
MOD6212/13 Transceiver Module Dimensions
Figure 2. MOD6212/13 Transceiver Module Dimension (in mm)
3 ©2017 SiBEAM, Inc., a Lattice Semiconductor company.
All rights reserved. CONFIDENTIAL
Module Installation Guide
O.D.
Master; SB6211/SB6213 Connect to Slave
4
SDA
Digital
In/Out
O.D.
I2C
I2C Data, Tunneling port. SB6210/SB6212 Connect to Master;
SB6211/SB6213 Connect to Slave
required for normal operation.
O.D.
required for normal operation.
the GPO pin on the opposite side of an active wireless link.
12
VBUS_SENSE
Digital
Input
USB
USB VBUS status input , 3V3
14
GND
Power
Power
Ground
16
SSRX-
Analog
Input
USB
USB Super speed Neg Input
18
SSRX+
Analog
Input
USB
USB Super speed Pos Input
27
LEDO
Digital
Output
Config
LED output
29
GPO/INT
Digital
Output
GPIO
General purpose output. When a wireless link is active, the
of the wireless link. Also used as I2C tunnel interupt
MOD6212/13 Transceiver Module Pinout
Table 1. Signal pinout
Pin Name Type Dir Group Description
1 3V3 Power Input Power 3.3V +/-5% power supply
2 SCL Digital
3 3V3 Power Input Power 3.3V +/-5% power supply
5 3V3 Power Input Power 3.3V +/-5% power supply
6 SCL_DBG I2C Bi-Dir USB
7 GND Power Power Ground
8 SDA_DBG I2C
9 GND Power Power Ground
10 GPI Digital Input GPIO
In/Out
In/Out
I2C
Debug
I2C Clock, Tunneling port. SB6210/SB6212 Connect to
I2C Data, Debug port. Connection to debug controller not
I2C Data, Debug port. Connection to debug controller not
General purpose input. Status of this input is reflected on
11 WAKE_UP Digital Input Control
13 ATB_N Analog Output Debug Differential analog test bus - negative terminal
15 ATB_P Analog Output Debug Differential analog test bus - positive terminal
17 RST Digital Input Config Reset Input, active HIGH
19 ID_IN Digital Input USB USB ID Input
20 GND Power Power Ground
21 ID_VAL Digital Input USB USB ID Valid Input
22 SSTX+ Analog Output USB USB Super speed Pos Output
23 ID_OUT Digital Output USB USB ID Output
24 SSTX- Analog Output USB USB Super speed Neg Output
25 VBUS_EN Digital Output USB USB VBUS status output, 3V3
26 GND Power Power Ground
28 D+ Analog Bi-Dir USB USB High Speed/Full Speed/Low Speed Pos I/O
Force the link to W0 State. This is useful to bypass USB states,
when I2C tunnel or GPI signal needs to be used, while the link
is in low power states. Active High. Optional.
status of this output reflects the GPI pin on the opposite side
30 D- Analog Bi-Dir USB USB High Speed/Full Speed/Low Speed Neg I/O
4 ©2017 SiBEAM, Inc., a Lattice Semiconductor company.
All rights reserved. CONFIDENTIAL
Module Installation Guide
MOD6212/13 Transceiver Module Connector
The module is designed to be connected to the system board through a single board to board
connector:
On the module side:
The connector type is DF40 from Hirose
Part number: DF40C-30DP-0.4V (51)
Description: Dual row Board to Board Receptacle (Plug), 0.4 pitch, 50 pins
A=7.52mm, B=5.6mm, C =1.5mm
Figure 3. Module side connector.
5 ©2017 SiBEAM, Inc., a Lattice Semiconductor company.
All rights reserved. CONFIDENTIAL
Loading...