Siamp STORM 33A, COMPACT 99B Assembly Instructions Manual

SINGLE FLUSH VALVE STORM 33A
BOTTOM INLET VALVE COMPACT 99B

ASSEMBLY INSTRUCTIONS

PJH

2

DESCRIPTION

a

c

d

e

h

i

f

g

b

j

k

m

n

l

o

3

Tools required (not spplied):

• Slotted screwdriver and adjustable
spanner.

FITTINGS SUPPLIED

Advice:

• Before you Start

- Read these instructions carefully.

- Check the pack and make sure you have all the parts on the pack list.

- Remove all packaging from pottery and check for surface damage or defects.

- Prepare a firm working surface (e.g; floor or bench) for cistern assembly, covering work
surface with cloth to prevent scratching the glazed faces of the cistern.

• Care & Use

- Wipe clean with a soft damp cloth around the WC suite.

- Never use scourers or abrasives.

• Water connection

- Water connection should be made only with an approved tap connector (not supplied).
Preparatory sealing compounds should not be used.

• Maintenance

Your new product is designed to have a long life span, however under certain conditions
e.g. hard water, «water hammer», excessive water pressure or installation debris in the
water pipe, it is possible that the life span of the diaphragm washer will be reduced.
To ensure long lasting customer satisfaction, a spare diaphragm washer is included in
this pack.

Pushbutton (1)
Valve body (1)
Rubber Washer (1)
Fixing nut (1)
Sealing Gasket (1)
Inlet valve (1)
Inlet Rubber Washer (1)
Backnut (1)

a

b

c

d

e

f

g

h

PARTS SUPPLIED

Spanner (1)

Bolt (2)

Sealing washer (2)

Washer (4)

Nut (2)

Butterfly nut (2)

Spare Diaphragm Washer (1)

i

j

k

l

m

n

o

4

I - ASSEMBLING THE INLET VALVE

II - ASSEMBLING THE OUTLET VALVE

Place Inlet valve (F) through Inlet
hole with inlet Rubber Washer
(G) inside the cistern.

Secure with backnut (H) but
ensure float moves freely up
and down valve body.

NB : Manually screw the backnut
until it is in contact with the
ceramic. If necessary give an
extra quarter turn (maximum).
Excessive tightening can
damage the mechanism and
would not be covered by the
guarantee.

Slide bolt (J) through washer
(K) and sealing washer (L) then
place through cistern and secure
with washer (K) and nut (M)
using adjustable spanner.

Assemble the valve body
(B) through cistern with
rubber washer (C) on
inside of the cistern.

Secure Fixing nut (D).

NB : Manually screw the
flush valve nut until it is in
contact with the ceramic.
If necessary give an extra
quarter turn (maximum)
with the spanner (I).

Excessive tightening can
damage the mechanism
and would not be covered
by the guarantee.

1

2

3

1

2

An approved double check valve or some other no
less effective backflow prevention device shall be
fitted at the point of connection(s) between the
supply and the fitting.

Try the lid on the cistern to see if
the valve is too high or too low :

To adjust :

Remove clips (x2) (1)

Unclip rod (2)

Adjust to correct height

Replace clips (x2) (1)

Push down at point (3) and clip
rod in at (2).

III - ASSEMBLING CISTERN TO PAN

Slide sealing gasket (E) over fixing nut

Slide cistern onto W.C. backplate by
locating screws through W.C.

Secure using butterfly nut (N).

IV - ADJUSTMENT OF VALVE HEIGHT

4

5

Butterfly
nut (N)

Cistern

Pan

(3)

(2)

(1)

5

1

2

3

1

2

3

6

V - SETTING WATER LEVEL

Connect the supply to the inlet valve.

N.B. : Make connecting tightness with filter

seal.

WARNINGS:

1 - Do not overtight in any case.
2 - Do not use any sealing paste and/or

compound in any case

3 - Do not use connector handling the

internal part of the inlet valve.

SIAMP will be not responsible in case
these warnings are not respected.

Allow cistern to fill and by screwing
the grey bolt slide the float to set
water level to waterline.

Ensure movement of float is not
restricted.

VI - ASSEMBLING THE BUTTON

Screw the button down, without
pushing the central part.

1

2

3

1

7

THE FINISHED ASSEMBLY INSIDE THE CISTERN

MAINTENANCE

Servicing the valve

To access the valve, unscrew
the assembly as shown.

(2)

(1)

For further enquiries

Contact Customer Services PJH on 0161 703 3360

1

To change the diaphragm washer inside the inlet valve

Turn off the water supply to the inlet valve.

Unscrew the knurled nut at the top of the
inlet valve

Remove the black rubber diaphragm
washer

Insert the replacement washer

Screw the nut back onto the inlet valve,
ensuring that the lift arm is holding the
float valve correctly

Turn the water supply back on

1

2

3

4

5

6

3

4

4, quai Antoine 1er - BP 219 - MC 98007 MONACO Cedex

Tél. [phone] - Fax : [phone]

E-mail: [e-mail]

Site Internet : http//: www.siamp.com

Réf. 50 5292 00

SINGLE FLUSH VALVE STORM 33A
BOTTOM INLET VALVE COMPACT 99B